EN 12663-2:2010/FprA1
(Amendment)Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons
Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons
Revised Annex ZA
Bahnanwendungen - Festigkeitsanforderungen an Wagenkästen von Schienenfahrzeugen - Teil 2: Güterwagen
Applications ferroviaires - Prescriptions de dimensionnement des structures de véhicules ferroviaires - Partie 2 : Wagons de marchandises
Železniške naprave - Konstrukcijske zahteve za grode železniških vozil - 2. del: Tovorni vagoni - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12663-2:2011/oprA1:2021
01-september-2021
Železniške naprave - Konstrukcijske zahteve za grode železniških vozil - 2. del:
Tovorni vagoni - Dopolnilo A1
Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight
wagons
Bahnanwendungen - Festigkeitsanforderungen an Wagenkästen von
Schienenfahrzeugen - Teil 2: Güterwagen
Applications ferroviaires - Prescriptions de dimensionnement des structures de véhicules
ferroviaires - Partie 2 : Wagons de marchandises
Ta slovenski standard je istoveten z: EN 12663-2:2010/prA1
ICS:
45.060.20 Železniški vagoni Trailing stock
SIST EN 12663-2:2011/oprA1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 12663-2:2011/oprA1:2021
SIST EN 12663-2:2011/oprA1:2021
DRAFT
EUROPEAN STANDARD
EN 12663-2:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2021
ICS 45.060.20
English Version
Railway applications - Structural requirements of railway
vehicle bodies - Part 2: Freight wagons
Applications ferroviaires - Prescriptions de Bahnanwendungen - Festigkeitsanforderungen an
dimensionnement des structures de véhicules Wagenkästen von Schienenfahrzeugen - Teil 2:
ferroviaires - Partie 2 : Wagons de marchandises Güterwagen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 256.
This draft amendment A1, if approved, will modify the European Standard EN 12663-2:2010. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12663-2:2010/prA1:2021 E
worldwide for CEN national Members.
SIST EN 12663-2:2011/oprA1:2021
EN 12663-2:2010/ prA1:2021 (E)
Contents Page
European foreword . 3
1 Modification to Clause 1, “Scope” . 4
2 Modification to Clause 2, “Normative references” . 4
3 Modification to 5.2.1, “General” . 4
4 Modification to 5.2.4.1, “Load cases for body to bogie connection” . 4
5 Modification to 6.1, “General” . 4
6 Modification to 6.3, “Design validation link to crashworthy buffer “ . 4
7 Modification to 7.1, “General” . 4
8 Modification to 8.2.1, “General” . 4
9 Modification to 8.2.4 Table 26, “Conditions for preliminary tests and serial buffing
tests” . 4
10 Changes Annex ZA, Relationship between this European Standard and the Essential
Requirements of EU Directive 2016/797/EC . 5
Annexe ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2016/797/EC . 6
SIST EN 12663-2:2011/oprA1:2021
EN 12663-2:2010/prA1:2021 (E)
European foreword
This document (EN 12663-2:2010/prA1:2021) has been prepared by Technical Committee CEN/TC 256
“Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN enquiry.
This document has been prepared under a standardization request addressed to CEN by the European
Commission, and it aims to support essential or other requirements of EU Directive(s) or Regulation(s).
For relationship with EU Directive(s) or Regulation(s), see informative Annex ZA which is an integral part
of this document.
SIST EN 12663-2:2011/oprA1:2021
EN 12663-2:2010/ prA1:2021 (E)
1 Modification to Clause 1, “Scope”
Replace “EN 12663-1” with the following: “EN 12663-1:2010+A1:2014”
2 Modification to Clause 2, “Normative references”
Replace the curre
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.