FprEN ISO 11670
(Main)Lasers and laser-related equipment - Test methods for laser beam parameters - Beam spatial stability (ISO/FDIS 11670:2026)
- Status
- Not Published
- Publication Date
- 28-Mar-2027
- Technical Committee
- CEN/TC 123 - Lasers and photonics
- Current Stage
- 4599 - Dispatch of FV draft to CMC - Finalization for Vote
- Start Date
- 15-Oct-2026
- Completion Date
- 15-Oct-2026
FprEN ISO 11670 is a CEN draft standard for lasers and laser-related equipment. It specifies test methods for laser beam spatial stability, covering both positional stability and angular stability, so users can characterize how a beam moves over time. The document is written for testing and characterization of lasers and explains how to measure centroid motion, derive fluctuation widths, and report the results.
What does FprEN ISO 11670 specify?
FprEN ISO 11670 specifies methods for determining laser beam positional stability and angular stability. In practice, it tells users how to set up a measurement plane, capture beam motion over time, and convert those measurements into reported stability values.
The document is organized into clauses 1 to 9. It covers scope, normative references, terms and definitions, the coordinate system, test principles, measurement arrangement and equipment, test procedures, evaluation, and the test report.
What are the key requirements of FprEN ISO 11670?
FprEN ISO 11670 focuses on measuring beam centroid motion, then turning that motion into position and angle stability values. The practical result is a repeatable way to compare lasers under defined operating conditions.
Coordinate system and measurement plane
Clause 4 requires an x-y-z laboratory coordinate system, with the z-axis approximately aligned with the beam. The transverse axes and the z location of the measurement plane have to be specified, because the results can depend on where along the beam path the measurement is made.
Position fluctuation widths
Clause 5.1 and Clause 7.2 define the position method. The beam is measured directly in the plane of interest or indirectly through an image of that plane, and at least 1 000 momentary centroid measurements are taken over the selected interval - short-term, medium-term, long-term, or user-defined.
This matters because the reported position fluctuation width comes from the spread of those centroid positions. If an image plane is used, the magnification has to be applied so the result refers back to the actual measurement plane.
Angular fluctuation widths
Clause 5.2 and Clause 7.3 define the angular method. The beam is measured in the focal plane of an auxiliary focusing element placed after the measurement plane, and the position fluctuation width in that focal plane is converted to angular fluctuation width by dividing by the focal length.
This means angular stability is not measured directly in angle terms at the detector. Instead, the setup turns angular motion into spatial motion at the focal plane, so the focal length becomes part of the calculation.
Measurement arrangement and detector behavior
Clause 6 requires the laser beam and measuring optics to be coaxial, with the full beam accommodated and clipping kept very low. The laser and test equipment must be thermally equilibrated, and the setup should minimize systematic error from reflections, ambient radiation, turbulence, blooming, vibration, acoustic disturbance, electrical noise, and temperature drift.
Clause 6.3 also requires the detector system to follow ISO 11146-1 and EN 61040:1990. The detector response has to be linear, wavelength effects and non-uniformity need correction or calibration, and the detector must not be damaged by the beam.
Calibration and sampling
Clause 6.5 requires calibration of detector sensitivity to lateral beam displacement before measuring position fluctuation width. Clause 7.1 also requires the detector and electronics bandwidth to be high enough for the sampling interval, so fast beam motion is not missed.
Evaluation and reporting
Clause 8 sets out the calculation sequence: determine centroid coordinates, calculate the mean, derive the displacement distribution, and then calculate the fluctuation width. Clause 9 lists the test report items, including laser identification, operating conditions, test method, detector and optics used, and the reported position and angular stability results.
What terms does FprEN ISO 11670 define?
FprEN ISO 11670 defines the measurement language used to describe beam motion. These terms are central to reading the calculation steps and the report.
- Momentary beam centroid coordinates - the x and y centroid positions of the beam at one moment in time at a given z location.
- Distribution of momentary beam centroid coordinates - the set of centroid positions collected from repeated measurements at the same location.
- Mean beam centroid coordinates - the arithmetic mean of the centroid distribution, used as the stable reference position.
- Position fluctuation widths - the numerical measure of how widely the centroid positions spread in the measurement plane.
- Momentary beam direction angles - the beam direction at one moment, expressed as differential change in centroid position per propagation length.
- Angular fluctuation widths - the numerical measure of how widely the direction angles spread at a given location.
- Beam spatial change from cold start - the change in beam position and direction between turn-on after thermal equilibration and the later warmed-up state.
Who uses FprEN ISO 11670?
FprEN ISO 11670 is used by laser manufacturers, test laboratories, and organizations that characterize laser performance. It is also relevant to quality and engineering teams that need a defined method for checking beam stability under specified operating conditions.
The standard is useful when a project needs comparable measurements of beam drift, beam direction change, or warm-up behavior. It supports product development, verification testing, and documentation for laser systems in optoelectronics and related fields.
What changed in FprEN ISO 11670 from the previous edition?
FprEN ISO 11670 cancels and replaces ISO 11670:2003. The document states that the main changes are a revised title, terms and definitions, and main text using the new term “Beam positional stability,” removal of rarely used terms and definitions, inclusion of new Figures 1 to 3, updated normative references, and removal of Annexes A and B.
Which standards are used with FprEN ISO 11670?
FprEN ISO 11670 relies on three named references.
- ISO 11145 - provides vocabulary and symbols for optics and laser-related equipment.
- ISO 11146-1 - gives the beam-width and divergence test framework that Clause 6.3 uses for detector-related provisions.
- EN 61040:1990 - provides the detector and instrument requirements for laser radiation measurement used in Clause 6.3.
What does the FprEN ISO 11670 document contain?
FprEN ISO 11670 contains definitions, a coordinate-system section, test principles, measurement arrangements, and step-by-step procedures for measuring spatial stability. It includes direct and indirect position measurement methods and an indirect angular method using a focusing element.
The document also includes three figures showing the direct position setup, the indirect position setup, and the angular setup. Clause 9 gives the reporting structure for test conditions, test equipment, and results, so the outcome can be documented in a consistent way.
Relations
- Consolidated By
ISO/FDIS 11670 - Lasers and laser-related equipment — Test methods for laser beam parameters — Beam spatial stability - Effective Date
- 12-Feb-2026
- Effective Date
- 04-Oct-2023
- Effective Date
- 04-Oct-2023
Frequently Asked Questions
FprEN ISO 11670 is a draft published by the European Committee for Standardization (CEN). Its full title is "Lasers and laser-related equipment - Test methods for laser beam parameters - Beam spatial stability (ISO/FDIS 11670:2026)". This standard covers: Lasers and laser-related equipment - Test methods for laser beam parameters - Beam spatial stability (ISO/FDIS 11670:2026)
Lasers and laser-related equipment - Test methods for laser beam parameters - Beam spatial stability (ISO/FDIS 11670:2026)
FprEN ISO 11670 is classified under the following ICS (International Classification for Standards) categories: 31.260 - Optoelectronics. Laser equipment. The ICS classification helps identify the subject area and facilitates finding related standards.
FprEN ISO 11670 has the following relationships with other standards: It is inter standard links to ISO/FDIS 11670, EN ISO 11670:2003/AC:2004, EN ISO 11670:2003. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
FprEN ISO 11670 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2025
Laserji in laserska oprema - Preskusne metode za parametre laserskega žarka -
Prostorska stabilnost žarka (ISO/DIS 11670:2025)
Lasers and laser-related equipment - Test methods for laser beam parameters - Beam
spatial stability (ISO/DIS 11670:2025)
Laser und Laseranlagen - Prüfverfahren für Laserstrahlparameter - Strahllagestabilität
(ISO/DIS 11670:2025)
Lasers et équipements associés aux lasers - Méthodes d'essai des paramètres du
faisceau laser - Stabilité de visée du faisceau (ISO/DIS 11670:2025)
Ta slovenski standard je istoveten z: prEN ISO 11670
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 11670
ISO/TC 172/SC 9
Lasers and laser-related
Secretariat: DIN
equipment — Test methods for
Voting begins on:
laser beam parameters — Beam
2025-05-09
spatial stability
Voting terminates on:
ICS: 31.260
2025-08-01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 11670:2025(en)
DRAFT
ISO/DIS 11670:2025(en)
International
Standard
ISO/DIS 11670
ISO/TC 172/SC 9
Lasers and laser-related
Secretariat: DIN
equipment — Test methods for
Voting begins on:
laser beam parameters — Beam
spatial stability
Voting terminates on:
ICS: 31.260
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 11670:2025(en)
ii
ISO/DIS 11670:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Coordinate system . 4
5 Test principles . 5
5.1 Position fluctuation widths .5
5.2 Angular fluctuation widths .5
6 Measurement arrangement, test equipment and auxiliary devices . 5
6.1 Preparation .5
6.2 Control of environment .6
6.3 Detection system .6
6.4 Optical attenuators, beam splitters, imaging optics, focusing elements .6
6.5 Calibration of detector sensitivity to lateral beam displacement .7
7 Test procedures . 7
7.1 General .7
7.2 Position fluctuation widths .7
7.3 Angular fluctuation widths .8
8 Evaluation . 9
8.1 Position fluctuation width .9
8.2 Angular fluctuation widths .9
9 Test report . 9
iii
ISO/DIS 11670:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 9,
Laser and electro-optical systems.
This third edition cancels and replaces the second edition (ISO 11670:2003), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Title, Terms and definitions and main text were revised using the new term “Beam positional stability”
— Rarely used terms and definitions have been removed
— New Figures 1 – 3 were included;
— standard was updated to new normative references.
— Annexes A and B have been removed
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/DIS 11670:2025(en)
Introduction
The centre of a laser beam in a plane perpendicular to the direction of propagation is defined as the centroid or
first-order spatial moment of the irradiance (fluence) distribution. The current propagation axis of a beam is
then the straight line connecting two centroids measured at two different planes simultaneously in a uniform,
homogeneous medium. Beam axis instabilities may be characterized by transverse position displacements
and by angular direction displacements that are either monotonic, periodic, or stochastic in time.
The magnitude of the transverse position fluctuations in a plane is quantified by the position displacement
width. A smaller position displacement width is equivalent to greater beam positional stability.
The magnitude of the angular fluctuations in a plane is quantified by the angular fluctuation width. A
smaller angular fluctuation width is equivalent to greater beam directional stability.
If the magnitude of the transverse fluctuations in an application plane is not significantly smaller than the
(instantaneous) beam diameter there, then, at longer exposure times, the laser radiation will be distributed
over a larger area as would be expected based on the beam diameter alone, leading to an increased effective
beam diameter and reducing the time-averaged energy density.
In the same manner angular fluctuations can increase the effective divergence of a laser beam.
The positional stability of the beam and the angular stability of the beam are referred to together as the
spatial stability of the beam.
This document provides general principles for the measurement of the positional und angular beam stability.
In addition, definitions of terminology and symbols to be used in referring to them are provided.
v
DRAFT International Standard ISO/DIS 11670:2025(en)
Lasers and laser-related equipment — Test methods for laser
beam parameters — Beam spatial stability
1 Scope
This document specifies methods for determining laser beam positional as well as angular stability. The test
methods given in this document are intended to be used for the testing and characterization of lasers.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 11145, Optics and optical instruments — Lasers and laser-related equipment — Vocabulary and symbols
ISO 11146-1, Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles and
beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams
EN 61040:1990, Power and energy measuring detectors, instruments and equipment for laser radiation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 61040, ISO 11145 and ISO 11146-1
and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
momentary beam centroid coordinates
xz() , yz()
first order moments of the momentary irradiance (fluence) of a fluctuating beam at location z measured
along the laboratory coordinates x and y of a beam propagating approximately in z direction
∫∫xE⋅ ()xy,,zx⋅ddy
xz =
()
∫∫Ex,,yz ⋅ddxy
()
∫∫ yE⋅ ()xy,,zx⋅ddy
yz() =
∫∫Ex(),,yz ⋅ddxy
Note 1 to entry: In general, since fluctuations are assumed, the irradiance (fluence) distribution as well as the
momentary beam centroid coordinates will vary from moment to moment (i.e., from measurement to measurement).
3.2
distribution of momentary beam centroid coordinates
xz() , yz()
ii
set of momentary beam centroid coordinates measured at different moments (times) at the same location z
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
ISO/DIS 11670:2025(en)
3.3
mean beam centroid coordinates
xz() ,yz()
MM
arithmetical mean of a distribution of momentary beam centroid coordinates at location z
N
xz()= xz()
M i
∑
N
i=1
N
yz()= yz()
M ∑ i
N
i=1
Note 1 to entry: If the number of measurements N of each set is sufficiently large, different sets measured on the same
beam at the same location z will results in approximately the same mean beam centroid coordinates. Thus, the mean
beam centroid coordinates may be considered as the (stable) beam centroid position at location z.
3.4
momentary position displacement
δδδxz ,δ yz
() ()
deviation of the momentary beam centroid coordinates from the mean beam centroid coordinates at location z
δxz()=xz()−xz()
M
δyz = yz − yz
() () ()
M
3.5
position displacement distributions
δδδxz() ,δ yz()
ii
set of momentary position displacements at location z
δxz =xz −xz
() () ()
ii M
δ yz()= yz()− yz()
ii M
Note 1 to entry: If N measurements have been made, the index i runs from 1 to N.
Note 2 to entry: If the number of measurements N is large enough, two independently measured position displacement
distributions of the same beam measured at the same location z, will have approximal the same extent, although the
distributions may not be identical.
3.6
position fluctuation widths
ΔΔΔxz() ,Δy()z
quantitative measures for the extent of a measured position displacement distribution at location z
N
δxz()
i
∑
i=1
Δxz =4
()
N−1
N
δ yz()
∑ i
i=1
Δy()z =4
N−1
Note 1 to entry: In general, the position fluctuation widths of a real beam will vary under free propagation through a
homogeneous medium. Thus, there will be indeed a dependency on the location z (in contrast to the angular fluctuation
width, see clause 3.12).
...



