EN 15895:2011/FprA1

Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools

This European standard covers safety requirements for cartridge operated fixing and hard marking tools which operate with an intermediate member (piston). This European standard deals with all significant hazards, hazardous situations and events relevant to cartridge operated fixing and hard marking tools, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). It deals with the significant hazards in the different operating modes and intervention procedures as referred to in EN ISO 12100-1:2003, 5.3. Although the safe use of cartridge operated tools depends to an important extent on the use of appropriate cartridges and fasteners, this standard is not formulating requirements for the cartridges and fasteners to be used with the tools (see Clause 7). This European Standard applies to tools designed for use with cartridges with casings made of metal or plastic and with solid propellant and containing a minor quantity of primer with a composition different from that of the main propellant. The fixing tools in the scope are those intended for use with fasteners made from metal. NOTE Information about cartridges can be found in the publication of the Permanent International Commission for the Proof of Small Arms (C.I.P.). This European standard is not applicable to cartridge operated fixing and hard marking tools which are manufactured before the date of its publication as EN.

Kartuschenbetriebene handgehaltene Werkzeuge - Sicherheit - Befestigungs- und Markierwerkzeuge

Outils portatifs à charge propulsive - Exigences de sécurité - Outils de scellement et de marquage

Ročna orodja z nabojnim delovanjem - Varnostne zahteve - Pritrjevalniki in označevalniki

General Information

• Status: Not Published
• ICS: 25.140.99 - Other hand-held tools
• Technical Committee: CEN/TC 213 - Cartridge operated hand-held tools - Safety
• Drafting Committee: CEN/TC 213/WG 1 - Cartridge Operated Fixing and Hard Marking tools
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 20-Apr-2017
• Completion Date: 20-Apr-2017
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 15895:2011/kFprA1:2017 - Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools

Relations

• Merged Into: EN 15895:2011+A1:2018 - Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools
• Effective Date: 18-Jan-2023
• Amends: EN 15895:2011 - Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools
• Effective Date: 11-May-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15895:2011/kFprA1:2017
01-april-2017
5RþQDRURGMD]QDERMQLPGHORYDQMHP9DUQRVWQH]DKWHYH3ULWUMHYDOQLNLLQ
R]QDþHYDOQLNL
Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools
Kartuschenbetriebene handgehaltene Werkzeuge - Sicherheit - Befestigungs- und
Markierwerkzeuge
Outils portatifs à charge propulsive - Exigences de sécurité - Outils de scellement et de
marquage
Ta slovenski standard je istoveten z: EN 15895:2011/FprA1
ICS:
25.140.99 'UXJDURþQDRURGMD Other hand-held tools
SIST EN 15895:2011/kFprA1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 15895:2011/kFprA1:2017

---------------------- Page: 2 ----------------------

SIST EN 15895:2011/kFprA1:2017


FINAL DRAFT
EUROPEAN STANDARD
EN 15895:2011
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
January 2017
ICS 25.140.99
English Version

Cartridge operated hand-held tools - Safety requirements -
Fixing and hard marking tools
Outils portatifs à charge propulsive - Exigences de Kartuschenbetriebene handgehaltene Werkzeuge -
sécurité - Outils de scellement et de marquage Sicherheit - Befestigungs- und Markierwerkzeuge
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 213.

This draft amendment A1, if approved, will modify the European Standard EN 15895:2011. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15895:2011/FprA1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 15895:2011/kFprA1:2017
EN 15895:2011/FprA1:2017 (E)
European foreword
This document (EN 15895:2011/FprA1:2017) has been prepared by Technical Committee CEN/TC 213
“Cartridge operated hand-held tools - Safety”, the secretariat of which is held by SNV.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
2

---------------------- Page: 4 ----------------------

SIST EN 15895:2011/kFprA1:2017
EN 15895:2011/FprA1:2017 (E)
1 Modification to the Introduction
Replace
"EN ISO 12100"
with
"EN ISO 12100:2010".
2 Modification to the Scope
Replace
"EN ISO 12100-1:2003, 5.3"
with
"EN ISO 12100:2010, 5.4, 5.5, 5.6."
3 Modification to Clause 2, Normative references
Replace
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)"
and
"EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical
principles (ISO 12100-2:2003)"
with
"EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
(ISO 12100:2010)".
4 Modifications to Clause 3, Terms and definitions
Replace
"EN ISO 12100-1:2003"
with
"EN ISO 12100:2010"
In 3.3.3, NOTE
replace
"6.3.2"
with
"6.4.2".
5 Modifications to Clause 4
In Table 1, No. 2.3, last column,
add
"5.3.4"
3

---------------------- Page: 5 ---
...