iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN/TS 15053:2005

(Main)

Non-destructive testing - Recommendations for discontinuities-types in test specimens for examination

Non-destructive testing - Recommendations for discontinuities-types in test specimens for examination

This Technical Specification is established to consider and define discontinuities-types to be exhibited in test specimens for use in practical Non Destructive Testing examinations. According to EN 473:2000, Clause 7.1.3.3, the discontinuities contains in the test specimens may be natural, artificial or implanted.
Acoustic Emission Testing, Infrared Thermography Testing and Leak Testing need not define discontinuity-type, due to their specific approach (e.g. replaced in AT by artificial sources).

Zerstörungsfreie Prüfung - Empfehlungen für Arten von Inhomogenitäten in Prüfungsstücken für Prüfungen

Dieses Dokument legt Arten von Inhomogenitäten fest, die Prüfungsstücke für die Verwendung in Qualifizierungsprüfungen von ZfP-Personal aufweisen müssen. Nach EN 473:2000, 7.1.3.3, dürfen die Inhomogenitäten in Prüfungsstücken natürlich sein, künstlich erzeugt oder eingebracht werden.
Wegen ihres spezifischen Vorgehens brauchen für die Schallemissionsprüfung, für die Infrarotthermografieprüfung und für die Dichtheitsprüfung Arten von Inhomogenitäten nicht festgelegt zu werden (z. B. bei AT Ersatz durch künstliche Quellen).

Essais non destructifs - Recommandations relatives aux types de discontinuités présentes dans les échantillons d'essai utilisés pour les examens

La présente Spécification technique est établie pour prendre en compte et définir les types de discontinuités que doivent comporter les échantillons utilisés lors des épreuves pratiques d'examens en Contrôle non destructifs. Conformément à l'EN 473:2000, paragraphe 7.1.3.3, les discontinuités contenues dans l'échantillon peuvent être naturelles, artificielles ou induites.
Compte-tenu de la spécificité des méthodes d'émission acoustique, de thermographie infrarouge et d'étanchéité, il est possible de ne pas définir de discontinuités-types (par exemple, sources artificielles utilisées en émission acoustique).

Neporušitveno preskušanje – Priporočila za vrste nezveznosti v preskusnih vzorcih

General Information

Status
Withdrawn
Publication Date
02-Aug-2005
Withdrawal Date
18-Feb-2020
ICS
19.100 - Non-destructive testing
Technical Committee
CEN/TC 138 - Non-destructive testing
Drafting Committee
CEN/TC 138 - Non-destructive testing
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
19-Feb-2020
Ref Project
SIST-TS CEN/TS 15053:2005 - Non-destructive testing - Recommendations for discontinuities-types in test specimens for examination

Buy Standard

TS CEN/TS 15053:2005TS CEN/TS 15053:2005
PreviousNext
Technical specification
TS CEN/TS 15053:2005
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 15053:2005
01-november-2005
1HSRUXãLWYHQRSUHVNXãDQMH±3ULSRURþLOD]DYUVWHQH]YH]QRVWLYSUHVNXVQLK
Y]RUFLK
Non-destructive testing - Recommendations for discontinuities-types in test specimens
for examination
Zerstörungsfreie Prüfung - Empfehlungen für Arten von Inhomogenitäten in
Prüfungsstücken für Prüfungen
Essais non destructifs - Recommandations relatives aux types de discontinuités
présentes dans les échantillons d'essai utilisés pour les examens
Ta slovenski standard je istoveten z: CEN/TS 15053:2005
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST-TS CEN/TS 15053:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 15053:2005

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 15053:2005
TECHNICAL SPECIFICATION
CEN/TS 15053
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
August 2005
ICS 19.100

English Version
Non-destructive testing - Recommendations for discontinuities-
types in test specimens for examination
Essais non destructifs - Recommandations relatives aux Zerstörungsfreie Prüfung - Empfehlungen für Arten von
types de discontinuités présentes dans les échantillons Inhomogenitäten in Prüfungsstücken für Prüfungen
d'essai utilisés pour les examens
This Technical Specification (CEN/TS) was approved by CEN on 7 May 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15053:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 15053:2005
CEN/TS 15053:2005 (E)
Contents
Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4

4 Product sectors.4
5 Minimum size of discontinuity .6
6 Surface conditions.8
7 Number of discontinuities in each sample.8
8 Radiographic interpretation test (radiographs) .8
9 Master report .9
Annex A (informative) Discontinuities in castings.10
Annex B (informative) Discontinuities in welds .11
Annex C (informative) Discontinuities in wrought products.12
Annex D (informative) Discontinuities in forgings.13
Annex E (informative) Discontinuities in tubes and pipes .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 5580:2023(Main)
Non-destructive testing - Industrial radiographic illuminators - Minimum requirements (ISO 5580:2023)
SIST EN ISO 5580:2024

The function of an industrial radiographic illuminator is to provide sufficient diffuse light for viewing of developed radiographic films (radiographs).
This document specifies the minimum requirements for industrial radiographic illuminators used for viewing radiographs.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7963:2022(Main)
Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)
SIST EN ISO 7963:2023

This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18563-1:2022(Main)
Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2022)
SIST EN ISO 18563-1:2022

This document specifies the functional characteristics of multi-channel ultrasonic phased array instruments used for array probes and provides methods for their measurement and verification.
This document is also applicable to ultrasonic phased array instruments in automated systems; but other tests can be needed to ensure satisfactory performance. When the phased array instrument is a part of an automated system, the acceptance criteria can be modified by agreement between the parties involved.
This document also can partly be applicable to FMC instruments and TFM instruments.
This document gives the extent of the verification and defines acceptance criteria within a frequency range of 0,5 MHz to 10 MHz.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17391:2022(Main)
Non-destructive testing - Acoustic emission testing - In-service acoustic emission monitoring of metallic pressure equipment and structures - General requirements
SIST EN 17391:2022

This document specifies general requirements for in-service acoustic emission (AE) monitoring. It relates to detection, location and grading of AE sources with application to metallic pressure equipment and other structures such as bridges, bridge ropes, cranes, storage tanks, pipelines, wind turbine towers, marine applications, offshore structures. The monitoring can be periodic, temporary or continuous, on site or remote-controlled, supervised or automated. The objectives of AE monitoring are to define regions which are acoustically active as a result of damage or defect evolution.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17501:2022(Main)
Non-destructive testing - Thermographic testing - Active thermography with laser excitation
SIST EN 17501:2022

This document specifies a method and establishes guidelines for non-destructive testing using active thermography with laser excitation.
Active thermography with laser excitation is mainly applicable, but not limited, to different materials (e.g. composites, metals, ceramics) and to:
- the detection of surface-breaking discontinuities, particularly cracks;
- the detection of discontinuities located just below the surface or below coatings with an efficiency that diminishes rapidly with a few mm depth;
- the detection of disbonds and delamination parallel to the examined surface;
- the measurement of thermal material properties, like thermal diffusivity;
- the measurement of coating thickness.
The requirements for the equipment, for the verification of the system, for the surface condition of the test object, for the scanning conditions, for the recording, the processing and the interpretation of the results are specified. This document does not apply to the definition of acceptance criteria.
Active thermography with laser excitation can be applied in industrial production as well as in maintenance and repair (vehicle parts, engine parts, power plant, aerospace, etc.).

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9712:2022(Main)
Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2021)
SIST EN ISO 9712:2022

This document specifies requirements for the qualification and certification of personnel who perform industrial non-destructive testing (NDT) in the following methods.
a) acoustic emission testing;
b) eddy current testing;
c) leak testing (hydraulic pressure tests excluded);
d) magnetic testing;
e) penetrant testing;
f) radiographic testing;
g) strain gauge testing;
h) thermographic testing;
i) ultrasonic testing;
j) visual testing (direct unaided visual tests and visual tests carried out during the application of another NDT method are excluded).
The system specified in this document is also applicable to other NDT methods or to NDT techniques within an established NDT method, provided a comprehensive scheme of certification exists and the NDT method or NDT technique is covered by international, regional or national standards or the NDT method or the NDT technique has been demonstrated to be effective to the satisfaction of the certification body.
NOTE 1    The term "industrial" implies the exclusion of applications in the field of medicine.
NOTE 2    CEN/TR 14748 provides guidance on the methodology for qualification of non-destructive tests.
NOTE 3    This document specifies requirements for what are, in effect, third party conformity assessment schemes. These requirements do not directly apply to conformity assessment by second or first parties, but relevant parts of this document can be referred to in such arrangements.
NOTE 4    The term “direct unaided visual testing” implies where there is an uninterrupted optical path from the observer’s eye to the test area and the observer uses no tools or devices (e.g. mirror, endoscope, fibre optic).
NOTE 5    Calculations of strain based on other NDT methods are excluded.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13477-2:2021(Main)
Non-destructive testing - Acoustic emission testing - Equipment characterisation - Part 2: Verification of operating characteristics
SIST EN 13477-2:2021

This document specifies test routines for the periodic verification of the performance of acoustic emission (AE) test equipment, i.e. sensors, pre-amplifiers, signal processors, external parametric inputs.
It is intended for use by qualified personnel to implement an automated verification process.
Verification of the measurement characteristics is advised after purchase of equipment, in order to obtain reference data for later verifications. Verification is also advised after repair, modifications, use under extraordinary conditions, or if one suspects a malfunction.
The procedures specified in this document do not exclude other qualified methods, e.g. verification in the frequency domain. These procedures apply in general unless the manufacturer specifies alternative equivalent procedures.
Safety aspects of equipment for use in potentially explosive zones are not considered in this document.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17290:2021(Main)
Non-destructive testing - Ultrasonic testing - Examination for loss of thickness due to erosion and/or corrosion using the TOFD technique
SIST EN 17290:2021

This document specifies the application of the time-of-flight diffraction (TOFD) technique in testing of metals for quantifying loss of thickness due to erosion and/or corrosion.
This document applies to all types of corrosion and/or erosion damage, particularly those defined in EN ISO 16809.
This document applies to unalloyed or low-alloyed steels.
It applies to components with a nominal thickness ≥ 6 mm. For smaller thicknesses, feasibility tests are performed to validate the test technique.
For other materials, feasibility tests are essential, too.
The TOFD technique can be used as a stand-alone technique or in combination with other non-destructive testing techniques, for in-service testing, in order to detect material loss caused by erosion and/or corrosion.
This technique is based on analysis of TOFD images using reflected and/or diffracted ultrasonic signals.
This document does not specify acceptance levels.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3452-2:2021(Main)
Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials (ISO 3452-2:2021)
SIST EN ISO 3452-2:2021

This document specifies the technical requirements and test procedures for penetrant materials for their type testing and batch testing. This document covers the temperature range from 10 °C to 50 °C. Additional tests in ISO 3452-5 or ISO 3452-6 can be required outside this range.
On-site control tests and methods are detailed in ISO 3452‑1.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3452-1:2021(Main)
Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2021)
SIST EN ISO 3452-1:2021

This document specifies a method of penetrant testing used to detect discontinuities, e.g. cracks, laps, folds, porosity and lack of fusion, which are open to the surface of the material to be tested using white light or UV-A (365 nm) radiation. It is mainly applied to metallic materials, but can also be performed on other materials, provided that they are inert to the test media and not excessively porous (castings, forgings, welds, ceramics, etc.)
This document also includes requirements for process and control testing, but is not intended to be used for acceptance criteria. It gives neither information relating to the suitability of individual test systems for specific applications nor requirements for test equipment.
NOTE 1   Methods for determining and monitoring the essential properties of penetrant testing products to be used are specified in ISO 3452-2 and ISO 3452-3.
NOTE 2   The term "discontinuity" is used in this document in the sense that no evaluation concerning acceptability or non-acceptability is included.
NOTE 3   CEN/TR 16638 addresses penetrant testing using actinic blue light.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day