EN 13445-3:2014/A5:2018
(Amendment)Unfired pressure vessels - Part 3: Design
Unfired pressure vessels - Part 3: Design
This Part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1:2009 and constructed of steels in accordance with EN 13445-2:2009. EN 13445-5:2009, Annex C specifies requirements for the design of access and inspection openings, closing mechanisms and special locking elements. NOTE This Part applies to design of vessels before putting into service. It may be used for in service calculation or analysis subject to appropriate adjustment.
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Dieser Teil 3 der Europäischen Norm legt die Anforderungen an die Konstruktion von unbefeuerten Druckbehältern
nach EN 13445-1:2014 und hergestellt aus Stählen nach EN 13445-2:2014 fest.
EN 13445-5:2014 gibt im Anhang C Bedingungen für die Konstruktion von Zugangs- und Besichtigungsöffnungen,
von Verschlüssen und besonderen Verschlusselementen.
ANMERKUNG Dieser Teil gilt für Konstruktion und Berechnung von Behältern vor der Inbetriebnahme. Er kann auch, mit
entsprechenden Anpassungen, für Berechnungen oder analytische Nachweise im Betrieb verwendet werden.
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Cette partie de la présente norme européenne spécifie les exigences relatives à la conception des récipients sous
pression non soumis à la flamme couverts par l’EN 13445-1:2014 et construits en aciers conformes à
l’EN 13445-2:2014.
L’Annexe C de l’EN 13445-5:2014 spécifie les exigences relatives à la conception des ouvertures d’accès et
d’inspection, des mécanismes de fermeture et des éléments de verrouillage spéciaux.
NOTE Cette partie s'applique à la conception des récipients avant mise en service. Elle peut être utilisée pour les calculs
ou l'analyse en service sous réserve d'apporter les ajustements appropriés.
Neogrevane (nekurjene) tlačne posode - 3. del: Konstruiranje - Dopolnilo A5
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13445-3:2014/A5:2018
01-december-2018
1HRJUHYDQH QHNXUMHQH WODþQHSRVRGHGHO .RQVWUXLUDQMH'RSROQLOR$
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Ta slovenski standard je istoveten z: EN 13445-3:2014/A5:2018
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
SIST EN 13445-3:2014/A5:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13445-3:2014/A5:2018
---------------------- Page: 2 ----------------------
SIST EN 13445-3:2014/A5:2018
EN 13445-3:2014/A5
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2018
EUROPÄISCHE NORM
ICS 23.020.30
English Version
Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Partie 3 : Conception
This amendment A5 modifies the European Standard EN 13445-3:2014; it was approved by CEN on 4 June 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-3:2014/A5:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13445-3:2014/A5:2018
EN 13445-3:2014/A5:2018 (E)
Contents Page
European foreword . 3
1 Modification to 5.4.2, Vessels of all testing groups, pressure loading predominantly
of non-cyclic nature . 4
2 Modifications to Clause 6, Maximum allowed values of the nominal design stress for
pressure parts . 4
3 Modifications to 17.1, Purpose . 5
4 Modifications to 17.2, Specific definitions . 5
5 Modification to 17.3, Specific symbols and abbreviations . 7
6 Modifications to 17.4, Conditions of applicability . 9
7 Modification to 17.5, General . 10
8 Modifications to 17.6, Determination of allowable number of pressure cycles . 16
9 Modifications to 17.9, Testing . 23
10 Addition of a new Annex U (informative), Guidance on negligibility of additional
thermal cycles in fatigue and ratcheting assessment . 23
2
---------------------- Page: 4 ----------------------
SIST EN 13445-3:2014/A5:2018
EN 13445-3:2014/A5:2018 (E)
European foreword
This document (EN 13445-3:2014/A5:2018) has been prepared by Technical Committee CEN/TC 54
“Unfired pressure vessels”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.