EN ISO 16610-1:2015
(Main)Geometrical product specifications (GPS) - Filtration - Part 1: Overview and basic concepts (ISO 16610-1:2015)
Geometrical product specifications (GPS) - Filtration - Part 1: Overview and basic concepts (ISO 16610-1:2015)
ISO 16610-1:2015 defines the basic terminology for GPS filtration and the framework for the fundamental procedures used in GPS filtration.
Geometrische Produktspezifikation (GPS) - Filterung - Teil 1: Überblick und grundlegende Konzepte (ISO 16610-1:2015)
Spécification géométrique des produits (GPS) - Filtrage - Partie 1: Vue d'ensemble et concepts de base (ISO 16610-1:2015)
L'ISO 16610-1:2015 définit la terminologie de base et la structure des principales méthodes utilisées pour le filtrage GPS.
Specifikacija geometrijskih veličin izdelka (GPS) - Filtriranje - 1. del: Pregled in osnovni pojmi (ISO 16610-1:2015)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16610-1:2015
01-julij-2015
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 )LOWULUDQMHGHO 3UHJOHGLQ
RVQRYQLSRMPL ,62
Geometrical product specifications (GPS) - Filtration - Part 1: Overview and basic
concepts (ISO 16610-1:2015)
Geometrische Produktspezifikation (GPS) - Filterung - Teil 1: Überblick und
grundlegende Konzepte (ISO 16610-1:2015)
Spécification géométrique des produits (GPS) - Filtrage - Partie 1: Vue d'ensemble et
concepts de base (ISO 16610-1:2015)
Ta slovenski standard je istoveten z: EN ISO 16610-1:2015
ICS:
17.040.20 Lastnosti površin Properties of surfaces
SIST EN ISO 16610-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16610-1:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 16610-1:2015
EUROPEAN STANDARD
EN ISO 16610-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2015
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Filtration - Part 1:
Overview and basic concepts (ISO 16610-1:2015)
Spécification géométrique des produits (GPS) - Filtrage - Geometrische Produktspezifikation (GPS) - Filterung - Teil
Partie 1: Vue d'ensemble et concepts de base (ISO 16610- 1: Überblick und grundlegende Konzepte (ISO 16610-
1:2015) 1:2015)
This European Standard was approved by CEN on 14 February 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16610-1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16610-1:2015
EN ISO 16610-1:2015 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16610-1:2015
EN ISO 16610-1:2015 (E)
Foreword
This document (EN ISO 16610-1:2015) has been prepared by Technical Committee ISO/TC 213 “Dimensional
and geometrical product specifications and verification” in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2015, and conflicting national standards shall be withdrawn at
the latest by October 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16610-1:2015 has been approved by CEN as EN ISO 16610-1:2015 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16610-1:2015
---------------------- Page: 6 ----------------------
SIST EN ISO 16610-1:2015
INTERNATIONAL ISO
STANDARD 16610-1
First edition
2015-04-
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.