EN ISO 7053:2011
(Main)Hexagon washer head tapping screws (ISO 7053:2011)
Hexagon washer head tapping screws (ISO 7053:2011)
ISO 7053:2011 specifies hexagon washer head tapping screws with thread sizes from ST 2,2 to ST 8 inclusive.
Sechskant-Blechschrauben mit Bund (ISO 7053:2011)
Diese Internationale Norm legt die Eigenschaften von Sechskant-Blechschrauben mit Bund mit Gewindegrößen
von ST 2,2 bis einschließlich ST 8 fest.
Vis à tôle à tête hexagonale à embase plate (ISO 7053:2011)
L'ISO 7053:2011 spécifie les caractéristiques des vis à tôle à tête hexagonale à embase plate, de diamètre de filetage ST 2,2 à ST 8 inclus.
Samorezni vijak s šestrobo glavo s podložko (ISO 7053:2011)
Ta evropski standard določa samorezne vijake s šestrobo glavo in podložko in križno zarezo od ST 2,2 do vključno ST 8.
Ta dokument je revizija že obstoječega ISO 7053.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7053:2011
01-november-2011
Samorezni vijak s šestrobo glavo s podložko (ISO 7053:2011)
Hexagon washer head tapping screws (ISO 7053:2011)
Sechskant-Blechschrauben mit Bund (ISO 7053:2011)
Vis à tôle à tête hexagonale à embase plate (ISO 7053:2011)
Ta slovenski standard je istoveten z: EN ISO 7053:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 7053:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7053:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 7053:2011
EUROPEAN STANDARD
EN ISO 7053
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2011
ICS 21.060.10
English Version
Hexagon washer head tapping screws (ISO 7053:2011)
Vis à tôle à tête hexagonale à embase plate (ISO Sechskant-Blechschrauben mit Bund (ISO 7053:2011)
7053:2011)
This European Standard was approved by CEN on 1 July 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7053:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7053:2011
EN ISO 7053:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7053:2011
EN ISO 7053:2011 (E)
Foreword
This document (EN ISO 7053:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn
at the latest by February 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 7053:2011 has been approved by CEN as a EN ISO 7053:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 7053:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 7053:2011
INTERNATIONAL ISO
STANDARD 7053
Second edition
2011-08-01
Hexagon washer head tapping screws
Vis à tôle à tête hexagonale à embase plate
Reference number
ISO 7053:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 7053:2011
ISO 7053:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 74
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.