EN ISO 15792-1:2020

Welding consumables - Test methods - Part 1: Preparation of all-weld metal test pieces and specimens in steel, nickel and nickel alloys (ISO 15792-1:2020)

This document specifies the preparation of test pieces and specimens for all-weld metal tests in steel, nickel and nickel alloys.
The test pieces and specimens are used to determine the mechanical properties of all-weld metal where required by consumable classification standards or for other purposes, in arc welding of steel, nickel and nickel alloys.
This document is not applicable to single- or two-run welding or fillet welding. For these cases, ISO 15792‑2 and ISO 15792‑3 apply.

Schweißzusätze - Prüfverfahren - Teil 1: Herstellung von Schweißgutprüfstücken und -proben an Stahl, Nickel und Nickellegierungen (ISO 15792 1:2020)

Dieses Dokument legt die Herstellung von Prüfstücken und der Proben für Prüfungen reinen Schweißguts an Stahl, Nickel und Nickellegierungen fest.
Die Prüfstücke und Proben werden für die Bestimmung der mechanischen Eigenschaften des reinen Schweißgutes verwendet, wenn sie durch Normen zur Einteilung von Schweißzusätzen oder für andere Zwecke beim Lichtbogenschweißen von Stahl, Nickel und Nickellegierungen gefordert werden.
Dieses Dokument gilt nicht für Einlagen- oder Zweilagen-Schweißungen oder Kehlnaht-Schweißungen. Für diese Fälle gelten ISO 15792 2 und ISO 15792 3.

Produits consommables pour le soudage - Méthodes d'essai - Partie 1: Préparation des pièces d'essai et des éprouvettes de métal fondu hors dilution pour le soudage de l'acier, du nickel et des alliages de nickel (ISO 15792-1:2020)

Le présent document spécifie la préparation des pièces d'essai et des éprouvettes pour les essais de métal fondu hors dilution dans l'acier, le nickel et les alliages de nickel.
Les pièces d'essai et les éprouvettes sont utilisées pour déterminer les propriétés mécaniques du métal fondu hors dilution lorsque ces propriétés sont exigées par les normes de classification du produit consommable ou pour d'autres besoins rencontrés en soudage à l'arc de l'acier, du nickel et des alliages de nickel.
Le présent document ne s'applique pas au soudage en une ou deux passes, ni à l'exécution de soudures d'angle. Pour ces cas, l'ISO 15792-2 et l'ISO 15792-3 s'appliquent.

Dodajni in pomožni materiali za varjenje - Preskusne metode - 1. del: Priprava zvarnega spoja in preskušancev za čisti var na jeklu, niklju in nikljevih zlitinah (ISO 15792-1:2020)

General Information

• Status: Published
• Publication Date: 15-Sep-2020
• Withdrawal Date: 30-Mar-2021
• ICS: 25.160.20 - Welding consumables
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 3 - Welding consumables
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 16-Sep-2020
• Completion Date: 16-Sep-2020
• Ref Project: SIST EN ISO 15792-1:2020 - Welding consumables - Test methods - Part 1: Preparation of all-weld metal test pieces and specimens in steel, nickel and nickel alloys (ISO 15792-1:2020)

Relations

• Replaces: EN ISO 15792-1:2008 - Welding consumables - Test methods - Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys (ISO 15792-1:2000)
• Effective Date: 23-Sep-2020
• Replaces: EN ISO 15792-1:2008/A1:2011 - Welding consumables - Test methods - Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys (ISO 15792-1:2000/Amd 1:2011)
• Effective Date: 23-Sep-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2020
Nadomešča:
SIST EN ISO 15792-1:2008
SIST EN ISO 15792-1:2008/A1:2013
Dodajni in pomožni materiali za varjenje - Preskusne metode - 1. del: Priprava
zvarnega spoja in preskušancev za čisti var na jeklu, niklju in nikljevih zlitinah
(ISO 15792-1:2020)
Welding consumables - Test methods - Part 1: Preparation of all-weld metal test pieces
and specimens in steel, nickel and nickel alloys (ISO 15792-1:2020)
Schweißzusätze - Prüfverfahren - Teil 1: Herstellung von Schweißgutprüfstücken und -
proben an Stahl, Nickel und Nickellegierungen (ISO 15792 1:2020)
Produits consommables pour le soudage - Méthodes d'essai - Partie 1: Préparation des
pièces d'essai et des éprouvettes de métal fondu hors dilution pour le soudage de l'acier,
du nickel et des alliages de nickel (ISO 15792-1:2020
Ta slovenski standard je istoveten z: EN ISO 15792-1:2020
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15792-1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 15792-1:2008
English Version
Welding consumables - Test methods - Part 1: Preparation
of all-weld metal test pieces and specimens in steel, nickel
and nickel alloys (ISO 15792-1:2020)
Produits consommables pour le soudage - Méthodes Schweißzusätze - Prüfverfahren - Teil 1: Herstellung
d'essai - Partie 1: Préparation des pièces d'essai et des von Schweißgutprüfstücken und -proben an Stahl,
éprouvettes de métal fondu hors dilution pour le Nickel und Nickellegierungen (ISO 15792 1:2020)
soudage de l'acier, du nickel et des alliages de nickel
(ISO 15792-1:2020)
This European Standard was approved by CEN on 29 August 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-1:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15792-1:2020) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15792-1:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15792-1:2020 has been approved by CEN as EN ISO 15792-1:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 15792-1
Second edition
2020-08
Welding consumables — Test
methods —
Part 1:
Preparation of all-weld metal test
pieces and specimens in steel, nickel
and nickel alloys
Produits consommables pour le soudage — Méthodes d'essai —
Partie 1: Préparation des pièces d'essai et des éprouvettes de métal
fondu hors dilution pour le soudage de l'acier, du nickel et des alliages
de nickel
Reference number
ISO 15792-1:2020(E)
©
ISO 2020
ISO 15792-1:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 15792-1:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 1
5 Test plate material . 1
6 Preparation of test piece . 2
7 Welding conditions . 2
8 Heat treatment . 3
9 Position of test specimens and test specimen dimensions . 3
Bibliography . 4
ISO 15792-1:2020(E)
Foreword
ISO (the International Organiza
...