EN ISO 19063-1:2015

Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19063-1:2015)

ISO 19063-1:2015 establishes a system of designation for impact-resistant polystyrene (PS-I) moulding and extrusion materials, which may be used as the basis for specifications.
The types of impact-resistant polystyrene plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties:
a)    Vicat softening temperature;
b)    melt mass-flow rate;
c)    Charpy notched impact strength;
d)    flexural modulus;
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19063 is applicable to all impact-resistant polystyrene plastics with a two-phase polymer system comprised of a continuous phase, consisting of polystyrene and/or a copolymer of styrene with an alkyl-substituted styrene, and a dispersed elastomeric phase based on butadiene.
It applies to materials ready for normal use, unmodified or modified by colorants, additives, fillers, etc.
ISO 19063-1:2015 does not apply to expandable materials.
It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19063 does not provide engineering data, performance data, or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 2897‑2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).

Kunststoffe - Schlagzähe Polystyrol (PS-I)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 19063-1:2015)

Der vorliegende Teil von ISO 19063 legt ein System für die Bezeichnung von schlagzähen Polystyrol (PS I)-Form¬massen fest, das als Grundlage für Spezifikationen angewendet werden darf.
Die Typen schlagzäher Polystyrol-Formmassen werden mit Hilfe eines Einteilungssystems voneinander unter¬schieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften
a)   Vicat-Erweichungstemperatur;
b)   Schmelze-Massefließrate;
c)   Charpy-Kerbschlagzähigkeit;
d)   Biegemodul;
und auf Informationen über die Zusammensetzung, vorgesehene Anwendung und/oder Ver¬ar¬bei¬tungs¬ver-fahren, wichtige Eigenschaften, Additive (Zusatzstoffe), Farbstoffe, Füll- und Verstärkungsstoffe beruht.
Dieser Teil von ISO 19063 gilt für alle schlagzähen Polystyrol-Kunststoffe mit einem zweiphasigen Polymer¬system, bestehend aus einer kontinuierlichen Phase auf Basis von Polystyrol und/oder eines Copolymers des Styrols mit alkylsubstituiertem Styrol und einer dispersen elastomeren Phase auf Basis von Butadien.
Er gilt für gebrauchsfertige Formmassen, die unmodifiziert oder mit Farbstoffen, Zusatzstoffen, Füllstoffen usw. modifiziert sind.
Dieser Teil von ISO 19063 gilt nicht für schäumbare Formmassen.
Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise das Gleiche leisten. Dieser Teil von ISO 19063 enthält keine technischen Daten, Leistungsangaben oder Angaben zu Ver¬¬arbeitungsbedingungen, die notwendig sein können, um eine Formmasse für eine bestimmte Anwen-dung und/oder Verarbeitungsart zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, werden sie nach den in ISO 2897-2 festgelegten Prüfverfahren, soweit geeignet, bestimmt.
Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine re¬pro¬du-zier¬bare Verarbeitung sicherzustellen, dürfen im Datenblock 5 (siehe 3.1) zusätzliche Anforderungen gestellt werden.

Plastiques - Polystyrènes résistants au choc (PS-I) pour moulage et extrusion - Partie 1 : Système de désignation et base de spécification (ISO 19063-1:2015)

ISO 19063-1:2015 établit un système de désignation des matériaux polystyrène résistants au choc (PS-I) pour moulage et extrusion, qui peut être utilisé comme base pour les spécifications.
Les types de plastiques polystyrène résistants au choc sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés de propriétés de désignation:
a)    température de ramollissement Vicat;
b)    indice de fluidité à chaud en masse;
c)    résistance au choc Charpy sur éprouvette entaillée;
d)    module de flexion;
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en ?uvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renforcement.
La présente partie de l'ISO 19063 est applicable à tous les plastiques polystyrènes résistants au choc présentant un système polymère à deux phases dans lequel la phase continue est constituée par du polystyrène et/ou du copolymère de styrène et de styrène substitué d'alcohyle, et une phase élastomérique dispersée ayant pour base le butadiène.
Elle s'applique aux matériaux prêts à l'emploi normal, non modifiés ou modifiés par des colorants, additifs, charges, etc.
ISO 19063-1:2015 ne s'applique pas aux matériaux extensibles.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 19063 ne comporte pas de données sur la conception, la performance ou les conditions de mise en ?uvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en ?uvre particulière.
Si de telles caractéristiques additionnelles sont nécessaires, elles seront déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 2897‑2, si appropriée.
Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en ?uvre reproductible, des exigences additionnelles peuvent être codées dans le bloc de données 5 (voir 3.1).

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz polistirena, odpornega proti udarcem (PS-I) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 19063-1:2015)

Ta del standarda ISO 19063 določa sistem označevanja materialov za oblikovanje in ekstrudiranje iz polistirena, odpornega proti udarcem (PS-I), ki jih je mogoče uporabiti kot podlago za specifikacije.
Vrste polimernih materialov iz polistirena, odpornega proti udarcem, se ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti:
a) temperaturi zmehčišča po Vicatu;
b) prostorninskem pretoku taline;
c) zarezni udarni žilavosti po Charpyju;
d) upogibnih modulih;
ter na informacijah o sestavi, nameravani uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje. Ta del standarda ISO 19063 velja za vse polimerne materiale iz polistirena, odpornega proti udarcem, ki imajo dvofazni polimerni sistem, sestavljen iz neprekinjene faze, sestavljene iz polistirena in/ali kopolimera stirena s stirenom, zamenjanim z alkilom, ter razpršene elastomerne faze, ki temelji na butadienu. Uporablja se za materiale, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, aditivi, polnili itd. Ta del standarda ISO 19063 se ne uporablja za razširljive materiale. Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 19063 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so lahko potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave.
Če so take dodatne lastnosti zahtevane, bodo določene v skladu s preskusnimi metodami iz standarda ISO 2897-2, če je to primerno. Da bi se določil termoplastični material za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, se lahko v podatkovnem bloku 5 navedejo dodatne zahteve (glej točko 3.1).

General Information

• Status: Published
• Publication Date: 01-Dec-2015
• Withdrawal Date: 29-Jun-2016
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 02-Dec-2015
• Completion Date: 02-Dec-2015
• Ref Project: SIST EN ISO 19063-1:2016 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19063-1:2015)

Relations

• Replaces: EN ISO 2897-1:1999 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997)
• Effective Date: 09-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2016
1DGRPHãþD
SIST EN ISO 2897-1:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]SROLVWLUHQD
RGSRUQHJDSURWLXGDUFHP36,GHO6LVWHPR]QDþHYDQMDLQSRGODJH]D
VSHFLILNDFLMH,62
Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1:
Designation system and basis for specifications (ISO 19063-1:2015)
Kunststoffe - Schlagzähe Polystyrol (PS-I)-Formmassen - Teil 1: Bezeichnungssystem
und Basis für Spezifikationen (ISO 19063-1:2015)
Plastiques - Polystyrènes résistants au choc (PS-I) pour moulage et extrusion - Partie 1:
Système de désignation et base de spécification (ISO 19063-1:2015)
Ta slovenski standard je istoveten z: EN ISO 19063-1:2015
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19063-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 2897-1:1999
English Version
Plastics - Impact-resistant polystyrene (PS-I) moulding
and extrusion materials - Part 1: Designation system and
basis for specifications (ISO 19063-1:2015)
Plastiques - Polystyrènes résistants au choc (PS-I) pour Kunststoffe - Schlagzähe Polystyrol (PS-I)-Formmassen
moulage et extrusion - Partie 1 : Système de - Teil 1: Bezeichnungssystem und Basis für
désignation et base de spécification (ISO 19063- Spezifikationen (ISO 19063-1:2015)
1:2015)
This European Standard was approved by CEN on 26 September 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19063-1:2015 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 19063-1:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 2897-1:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19063-1:2015 has been approved by CEN as EN ISO 19063-1:2015 without any
modification.
INTERNATIONAL ISO
STANDARD 19063-1
First edition
2015-11-15
Plastics — Impact-resistant
polystyrene (PS-I) moulding and
extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Polystyrènes résistants au choc (PS-I) pour moulage
et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 19063-1:2015(E)
©
ISO 2015
ISO 19063-1:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 19063-1:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Designation system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 2
3.4 Data block 3 . 3
3.5 Data block 4 . 4
3.5.1 Vicat softening temperature . 4
3.5.2 Melt mass-flow rate . 4
3.5.3 Charpy notched impact strength. 5
3.5.4 Flexural modulus . 5
3.6 Data block 5 . 5
4 Examples of designations . 6
ISO 19063-1:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19063-1 cancels and replaces ISO 2897-1:1997, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 2897-1. If the existing ISO 2897-1 would be replaced by the new designation system, these
documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 2897-1 to ISO 19063-1, any designation system according
to ISO 2897-1 is to be phased out in 5 to 10 years. During this period, ISO 2897-2 will effectively be Part
2 of this International Standard.
ISO 19063 consists of the following parts, under the general title Plastics — Impact-resistant polystyrene
(PS-I) moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
iv © ISO 2015 – All rights reserved

ISO 19063-1:2015(E)
Introduction
ISO 2897-1 is complex and does not fit with daily practice anymore. In practice, ISO 1043 (all parts)
and ISO 11469 are, in combination, “improperly” being used as a designation system for, e.g. marking.
The aim of this International Standard is to simplify the data block system and to connect more to
ISO 1043 (all parts) and ISO 11469, where the first two blocks are used for generic identification and
marking of products.
INTERNATIONAL STANDARD ISO 19063-1:2015(E)
Plastics — Impact-resistant polystyrene (PS-I) moulding
and extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
This part of ISO 19063 establishes a system of designation for impact-resistant polystyrene (PS-I)
moulding and extrusion materials, which may be used as the basis for specifications.
The types of impact-resistant polystyrene plastic are differentiated from each other by a classification
system based on appropriate levels of the designatory properties:
a) Vicat softening temperature;
b) melt mass-flow rate;
c) Charpy notched impact strength;
d) flexural modulus;
and on information about composition, intended application and/or method of processing, important
properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19063 is applicable to all impact-resistant polystyrene plastics with a two-phase
polymer system comprised of a continuous phase, consisting of polystyrene and/or a copolymer of
styrene with an alkyl-substituted styrene, and a dispersed elastomeric phase based on butadiene.
It applies to materials ready for normal use, unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 19063 does not apply to expandable materials.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 19063 does not provide engineering data, perf
...