prEN 507
(Main)Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet
Roofing and cladding products from metal sheet - Specification for fully supported products of aluminium sheet
This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2:-.
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Das vorliegende Dokument legt die Anforderungen an Dachdeckungs- und Wandbekleidungselemente fest, die für die Herstellung von Außen- und Innenwandbekleidungen sowie Eindeckungen von geneigten Dächern verwendet werden und aus Aluminiumblech mit oder ohne zusätzliche Oberflächenbehandlung (organische Beschichtungen oder Anodisierung) bestehen.
Dieses Dokument legt allgemeine Merkmale, Definitionen und Beschriftung der Elemente fest, sowie die Anforderungen an die Werkstoffe, aus denen die Elemente hergestellt werden können. Es ist dafür bestimmt, von Herstellern verwendet zu werden, um sicherzustellen, dass ihre Produkte den Anforderungen entsprechen, oder von Käufern, um zu überprüfen, ob die Produkte in Einklang mit den Anforderungen stehen, bevor sie das Werk verlassen. Es legt die Anforderungen fest, unter denen die Elemente allen üblichen Einsatzbedingungen gerecht werden. Bei den Dachdeckungselementen kann es sich um vorgefertigte oder halbfertige Elemente sowie um Blechstreifen, Band und Blech für die Verarbeitung auf der Baustelle (z. B. Stehfalzdächer) handeln.
Dieses Dokument gilt für alle überlappenden, vollflächig unterstützten Dachdeckungs- und Wandbekleidungselemente aus Aluminiumblech. Anforderungen an die Unterkonstruktion, die Konstruktion des Dachsystems sowie die Ausführung von Verbindungen und Zubehörteilen sind nicht Teil dieses Dokuments.
Dieses Dokument gilt nicht für selbsttragende Aluminiumbleche, die in EN 508 2:- behandelt werden.
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de couverture en tôle d'aluminium totalement supportés
Le présent document spécifie les exigences relatives aux produits de couverture et de bardage utilisés pour l'assemblage de couvertures, de bardages, de parements intérieurs et de toits en pente, fabriqués à partir de tôles d'aluminium, avec ou sans traitement de surface supplémentaire (revêtement organique ou anodisation).
Le présent document donne les caractéristiques générales, les définitions et l'étiquetage applicables aux produits, de même que les exigences relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Il est destiné à être utilisé soit par les producteurs, en vue de démontrer que leurs produits sont conformes aux exigences, soit par les acheteurs pour vérifier que les produits sont conformes avant leur expédition de l'usine. Il spécifie les exigences relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service. Les produits peuvent être des produits préfabriqués ou semi-formés, ainsi que des bandes, des bobines ou des tôles pour des applications de façonnage sur chantier (par exemple, les couvertures à joints debout).
Le présent document s'applique à tous les produits de couverture et de bardage posés en discontinu et totalement supportés réalisés à partir de tôles en aluminium. Il ne comporte aucune exigence relative à la construction des supports, à la conception de la couverture et à l’exécution des assemblages et des solins.
Le présent document ne traite pas des tôles d’aluminium autoportantes, qui sont couvertes par l’EN 508-2 :-.
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte proizvode iz aluminijske pločevine
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2025
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za povsem podprte
proizvode iz aluminijske pločevine
Roofing and cladding products from metal sheet - Specification for fully supported
products of aluminium sheet
Dachdeckungs- und Wandbekleidungselemente aus Metallblech - Festlegungen für
vollflächig unterstützte Bedachungselemente aus Aluminiumblech
Produits de couverture et bardage en tôle métallique - Spécification pour les produits de
couverture en tôle d'aluminium totalement supportés
Ta slovenski standard je istoveten z: prEN 507
ICS:
77.150.10 Aluminijski izdelki Aluminium products
91.060.20 Strehe Roofs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2025
ICS 91.060.20 Will supersede EN 507:2019
English Version
Roofing and cladding products from metal sheet -
Specification for fully supported products of aluminium
sheet
Produits de couverture et bardage en tôle métallique - Dachdeckungs- und Wandbekleidungselemente aus
Spécification pour les produits de couverture en tôle Metallblech - Festlegungen für vollflächig unterstützte
d'aluminium totalement supportés Bedachungselemente aus Aluminiumblech
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 128.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 507:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, symbols and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Symbols and abbreviations . 6
4 Requirements . 7
4.1 General. 7
4.2 Materials . 7
4.2.1 Aluminium . 7
4.2.2 Organic coatings . 8
4.2.3 Anodizing . 9
4.3 Products . 9
4.3.1 Flat products . 9
4.3.2 Formed (prefabricated) products . 9
4.3.3 Safety in case of fire. 9
5 Sampling and test methods . 10
5.1 Flat products . 10
5.2 Formed (prefabricated) products . 10
5.2.1 Sampling . 10
5.2.2 Testing . 10
6 Designation . 10
7 Marking, labelling and packaging . 10
7.1 Marking and labelling . 10
7.2 Packaging and any special ordering conditions . 11
7.3 Transport, storage and handling . 11
Bibliography . 12
European foreword
This document (prEN 507:2025) has been prepared by Technical Committee CEN/TC 128 “Roof
covering products for discontinuous laying and products for wall cladding”, the secretariat of which is
held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 507:2019.
The list of aluminium alloys suitable for roofing and cladding products has been extended.
These changes or additions can be found in the following sections: 4.2.1.
Introduction
Figure 1 indicates the position of this document in the CEN framework of standards concerning roofing
and cladding products of metal sheet.
Roofing and cladding products
of metal sheet
Self supporting Fully supported products
products
EN 14783
EN 14782
Zinc Stainless steel Copper Steel Aluminium
EN 501 EN 502 EN 504 EN 505 EN 507
References regarding
Materials
Quality
assurance
Figure 1 — Framework of standards
In this document the performance of the product has been defined in terms of a number of type tests.
The performance of a roof or cladding constructed with these products depends not only on the
properties of the product as it is required by this document, but also on the design, construction and
performance of the roof or the cladding as a whole in relation to the environment and conditions of use.
Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn,
folded, roll-formed without difficulty within the given limits of the properties listed in the respective
material specifications.
Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but
minimum bend radius, design of forming tools, process temperature etc are chosen according to
material properties.
1 Scope
This document specifies requirements for roofing and cladding products used for assembly into
coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without
additional surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together
with requirements for the materials from which the products can be manufactured. It is intended to be
used either by manufacturers to ensure that their products comply with the requirements or by
purchasers to verify that the products comply before they are despatched from the factory. It specifies
the requirements for products which enable them to meet all normal service conditions. Products can
be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications
(e.g. standing seam roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products
made of aluminium sheets. No requirements for supporting construction, design of roof system and
execution of connections and flashings are included.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2:—.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 485-1, Aluminium and aluminium alloys — Sheet, strip and plate — Part 1: Technical conditions for
inspection and delivery
EN 485-2, Aluminium and aluminium alloys — Sheet, strip and plate — Part 2: Mechanical properties
EN 485-4, Aluminium and aluminium alloys — Sheet, strip and plate — Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 1396, Aluminium and aluminium alloys — Coil coated sheet and strip for general applications —
Specifications
EN 10204, Metallic products — Types of inspection documents
EN ISO 7599, Anodizing of aluminium and its alloys — General specifications for anodic oxidation coatings
on aluminium (ISO 7599)
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 485-1 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
NOTE Wherever the term aluminium is used it is meant unalloyed or alloyed aluminium.
3.1.1
fully supported
installation conditions such that the bottom flat portions of the products are supported by a continuous
construction
3.1.2
temper
material conditions after a production stage, for example mechanical treatment and/or heat treatment,
intended to give the material physical and/or metallurgical properties
[SOURCE: EN 508-2:—, definition 3.2.1]
3.1.3
organic coated aluminium sheet
painted, post coated, laminated or coil coated (continuously organic coated) aluminium on one or on
both sides
[SOURCE: EN 508-2:—, definition 3.2.2]
3.1.4
anodised aluminium sheet
aluminium with an anodic coating, produced by an electrolytic oxidation process in which the surface of
the aluminium is converted to a mainly oxide coating having protective, decorative or functional
properties
3.2 Symbols and abbreviations
For the purposes of this document, the following symbols and abbreviations apply.
AK indicating alkyd paint coating
AY indicating acrylic paint coating
EN AW symbols for aluminium sheets identical to the alloy symbols given in Table 2
EP epoxy paint coating for use within a building
H the aluminium temper symbol
PMD indicating polyamid coated
PUR polyurethane paint coating
PUR-PA polyamide-modified polyurethane paint coating
PVDF indicating polyvinylidenefluoride paint coating
PVF(F) indicating polyvinylfluoride film coating
SP indicating polyester paint coating
SP-PA polyamid-modified polyester paint coating
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.