Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 5: Derivation of Test Specifications

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4.
NOTE   To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particular has to be considered for the determination of the test intensity.

Transportbelastungen - Messen und Auswerten von mechanisch-dynamischen Belastungen - Teil 5: Ableitung von Prüfvorschriften

Diese Norm enthält Leitlinien für die Ableitung von Prüfvorschriften aufgrund der nach EN 15433-2, EN 15433-3 und EN 15433-4 erfassten Daten.
ANMERKUNG   Zur Simulation von Transportbelastungen sind standardisierte Lastannahmen hilfreich, die auf den nach EN 15433-2 bis EN 15433-4 ermittelten Belastungen beruhen. Die Ableitung von Prüfvorschriften beruht grundsätzlich auf Überlegungen zur Schadensnachbildung, wobei insbesondere die zeitgeraffte Lebensdauersimulation bei der Bestimmung der Prüfintensität zu berücksichtigen ist.

Charges de transport - Mesurage et analyse des charges mécaniques dynamiques - Partie 5: Dérivation des spécifications d'essai

La présente norme donne des directives relatives à la dérivation des spécifications d’essai de données acquises conformément à l’EN 15433-2, l’EN 15433-3 et l’EN 15433-4.
NOTE   Pour simuler les charges de transport, il est utile de travailler avec des hypothèses de charges normalisées qui sont basées sur les charges réelles obtenues selon les normes EN 15433-2 à EN 15433-4. La dérivation des spécifications d’essai est surtout basée sur des considérations relatives à la reproduction des dommages, au moyen de laquelle la simulation de fatigue due à la compression du temps en particulier doit être prise en compte pour la détermination de l’intensité de l’essai.

Obremenitve pri transportu - Merjenje in analiza dinamično mehanskih obremenitev - 5. del: Izpeljava specifikacij preskušanja

General Information

Status
Published
Publication Date
04-Dec-2007
Withdrawal Date
29-Jun-2008
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
02-Dec-2023
Completion Date
02-Dec-2023

Buy Standard

Standard
EN 15433-5:2008
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Transportation loads - Measurement and evaluation of dynamic-mechanical loads - Part 5: Derivation of Test SpecificationsNLKCharges de transport - Mesurage et évaluation des charges mécaniques dynamiques - Partie 5 : Dérivation des spécifications d’essaiTransportbelastungen - Messen und Auswerten von mechanisch-dynamischen Belastungen - Teil 5: Ableitung von PrüfvorschriftenTa slovenski standard je istoveten z:EN 15433-5:2007SIST EN 15433-5:2008en,de55.180.01ICS:SLOVENSKI
STANDARDSIST EN 15433-5:200801-februar-2008







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15433-5December 2007ICS 55.180.01 English VersionTransportation loads - Measurement and evaluation of dynamicmechanical loads - Part 5: Derivation of Test SpecificationsCharges de transport - Mesurage et analyse des chargesmécaniques dynamiques - Partie 5: Dérivation desspécifications d'essaiTransportbelastungen - Messen und Auswerten vonmechanisch-dynamischen Belastungen - Teil 5: Ableitungvon PrüfvorschriftenThis European Standard was approved by CEN on 28 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15433-5:2007: E



EN 15433-5:2007 (E) 2 Contents
Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Derivation of test conditions.5 4 Parameters for the derivation of test conditions.5 5 Derivation procedure.6 6 Derivation of test spectra for failure mechanisms.6 Annex A (informative)
Numerical example for the determination of a test spectrum for one road category and one load factor only.24 Bibliography.26



EN 15433-5:2007 (E) 3 Foreword This document (EN 15433-5:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



EN 15433-5:2007 (E) 4
Introduction This standard was originally prepared
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.