EN 1517:2020
(Main)Surfaces for sports areas - Determination of resistance to impact
Surfaces for sports areas - Determination of resistance to impact
This document specifies a method for the determination of resistance to impact of sports floor systems. It is primarily designed to be used on surfaces intended for use in indoor sports halls. The test can be undertaken in the laboratory or on site.
When undertaking tests on site, it is important to note that permanent damage to the sports floor can be caused.
Sportböden - Bestimmung der Schlagfestigkeit
Dieses Dokument legt ein Verfahren zur Bestimmung der Schlagfestigkeit von Sportbodensystemen fest. Es ist hauptsächlich für Oberflächen entwickelt, die für die Verwendung in Sporthallen vorgesehen sind. Die Prüfung kann im Labor oder vor Ort durchgeführt werden.
Es ist wichtig darauf hinzuweisen, dass bei der Durchführung von Prüfungen vor Ort ein Dauerschaden am Sportboden verursacht werden kann.
Sols sportifs - Détermination de la résistance au choc
Le présent document spécifie une méthode permettant de déterminer la résistance au choc de certains systèmes sols sportifs. Cette méthode est principalement conçue pour être utilisée sur des sols destinés aux salles de sport. L'essai peut être réalisé en laboratoire ou sur site.
Lorsque les essais sont réalisés sur site, il est important de noter que le sol sportif peut subir des dommages permanents.
Podloge za športne dejavnosti - Ugotavljanje odpornosti proti udarcu
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN 1517:2002
Podloge za športne dejavnosti - Ugotavljanje odpornosti proti udarcu
Surfaces for sports areas - Determination of resistance to impact
Sportböden - Bestimmung der Schlagfestigkeit
Sols sportifs - Détermination de la résistance au choc
Ta slovenski standard je istoveten z: EN 1517:2020
ICS:
97.220.10 Športni objekti Sports facilities
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 1517
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 97.220.10 Supersedes EN 1517:1999
English Version
Surfaces for sports areas - Determination of resistance to
impact
Sols sportifs - Détermination de la résistance au choc Sportböden - Bestimmung der Schlagfestigkeit
This European Standard was approved by CEN on 2 March 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1517:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 4
6 Test specimen . 5
7 Conditioning . 5
8 Procedure. 6
9 Test report . 6
European foreword
This document (EN 1517:2020) has been prepared by Technical Committee CEN/TC 217 “Surfaces for
sports areas”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards shall
be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1517:1999.
The main changes compared to the previous edition are listed below:
— enhanced description of test apparatus,
— more defined procedure for assessing cracking, delamination or permanent indentation,
— procedure for on-site tests.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.