EN 4840-002:2023
(Main)Aerospace series - Heat shrinkable moulded shapes - Part 002: Index of product standards and product dimensions
Aerospace series - Heat shrinkable moulded shapes - Part 002: Index of product standards and product dimensions
This document lists the product standards, covered by technical specification EN 4840-001, for heat-shrinkable moulded shapes.
Luft-und Raumfahrt - Wärmeschrumpfende Formteile - Teil 002: Übersicht über die Produktnormen und Produktmaße
In diesem Dokument sind die Produktnormen für wärmeschrumpfende Formteile aufgeführt, die in EN 4840 001, Technische Lieferbedingungen, enthalten sind.
Série aérospatiale - Manchons thermorétractables - Partie 002 : Index des normes de produits et dimensions des produits
Le présent document répertorie les normes de produits couvertes par la spécification technique EN 4840-001 pour les manchons thermorétractables.
Aeronavtika - Toplotno skrčljive ulite forme - 002. del: Indeks standardov in dimenzij izdelkov
Ta dokument navaja standarde za izdelke, ki jih zajema tehnična specifikacija standarda EN 4840-001 za toplotno skrčljive ulite forme.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2024
Aeronavtika - Toplotno skrčljive ulite forme - 002. del: Indeks standardov in
dimenzij izdelkov
Aerospace series - Heat shrinkable moulded shapes - Part 002: Index of product
standards and product dimensions
Luft-und Raumfahrt - Wärmeschrumpfende Formteile - Teil 002: Übersicht über die
Produktnormen und Produktabmessungen
Série aérospatiale - Manchons thermorétractables - Partie 002 : Index des normes de
produits et dimensions des produits
Ta slovenski standard je istoveten z: EN 4840-002:2023
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 4840-002
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 29.035.20; 49.060
English Version
Aerospace series - Heat shrinkable moulded shapes - Part
002: Index of product standards and product dimensions
Série aérospatiale - Manchons thermorétractables - Luft-und Raumfahrt - Wärmeschrumpfende Formteile -
Partie 002 : Index des normes de produits et Teil 002: Übersicht über die Produktnormen und
dimensions des produits Produktabmessungen
This European Standard was approved by CEN on 30 October 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4840-002:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Index of product standards . 4
5 Product dimensions . 4
Bibliography . 29
European foreword
This document (EN 4840-002:2023) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by June 2024, and conflicting national standards shall be withdrawn at
the latest by June 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this document: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document lists the product standards, covered by technical specification EN 4840-001, for heat-
shrinkable moulded shapes.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
4 Index of product standards
EN 4840-001, Aerospace series — Heat-shrinkable moulded shapes — Part 001: Technical specification
EN 4840-101, Aerospace series — Heat-shrinkable moulded shapes — Part 101: Polyolefin, semi-rigid,
limited fire hazard — Temperature range –30 °C to 105 °C — Product standard
EN 4840-102, Aerospace series — Heat-shrinkable moulded shapes — Part 102: Elastomeric, semi-rigid,
temperature range –75 °C to 150 °C — Product standard
EN 4840-103, Aerospace series — Heat-shrinkable moulded shapes — Part 103: Fluoroelastomeric,
temperature range −55 °C to 200 °C — Product standard
5 Product dimensions
See Figure 1 to Figure 23 and Table 1 to Table 23.
Recovered As supplied
Detail X
Figure 1 — Style AA (small lipped bottle)
Table 1 — Style AA
Dimensions are in millimetres
Size code d d d l l l l S S S Mass g
1 2 3 1 2 3 4 1 2 3
b
Max.
Max. Max. a ± 10 % ref ref Max. ± 20 % ± 20 % ± 30 %
Min.
01 5,2 1,5 9 20 4 6,6 0,8 0,35 0,8 0,6 1,5
02 5,8 1,2 10 19 11 4,5 1,5 0,5 0,8 0,5 1,5
03 5,5 2 9 25 14 5 2 1 1 0,7 1,5
04 7 3 12 25 14 7,5 2 1 1,1 0,7 1,5
05 8 3,5 17 30 19 10 2 1 1,3 0,7 1,5
06 6,9 3,0 17 29 14 11 2 1 1,3 0,7 1,5
07 6,9 3,0 17 39 24 11 2 1 1,3 0,7 1,5
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual
manufacturer for details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual manufacturer
for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
Recovered As supplied
Detail X As supplied
(size code 02 only)
Figure 2 — Style A (lipped short bottle with short body)
Table 2 — Style A
Dimensions are in millimetres
d d d l l l l S S S b
Size code
1 2 3 1 2 3 4 1 2 3 Mass g Max.
a
Max. Max. ± 10 % ref ref Max. ± 20 % ± 20 % ± 30 %
Min.
c
01 10,5 6,0 24,0 26,0 9,0 10,0 1,6 1,6
c
02 14,0 3,5 25,0 40,0 13,0 16,0 1,8 3,3
03 14,0 6,0 30,0 43,0 20,0 13,0 1,0 1,8 4,5
04 18,0 7,0 31,0 47,0 15,0 18,0 1,8 5,5
1,0
05 22,5 8,5 36,0 60,0 22,0 20,0 3,3 2,0 10,0
06 28,0 10,0 43,0 60,0 21,0 20,0 1,7 2,2 12,7
07 35,0 16,0 60,0 90,0 32,0 38,0 1,7 3,2 1,5 29,5
08 45,0 17,0 66,0 130,0 50,0 50,0 2,0 3,8 2,0 71,5
09 58,0 27,0 82,0 137,0 37,0 62,0 2,0 3,8 3,8 100,0
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual manufacturer for exact
dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
c
For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm.
Recovered As supplied
Detail X As supplied
(size code 02 only)
Figure 3 — Style B (lipped straight bottle with medium body)
Table 3 — Style B
Dimensions are in millimetres
d d d l l l b l S S S c
Size code
1 2 3 1 2 3 l 5 1 2 3 Mass g Max.
a
Max. Max. ± 10 % ref ref ± 10 % ± 20 % ± 20 % ± 30 %
Min.
Max.
d
01 10,5 6,0 24,0 38,0 21,0 10,0 12,0 1,6 2,8
d
02 14,0 3,5 25,0 55,0 28,0 16,0 14,0 1,8 4,4
03 14,0 6,0 30,0 55,0 32,0 13,0 12,0 1,0 1,8 5,5
04 18,0 7,0 31,0 67,0 35,0 18,0 1,8 8,3
1,0
05 22,5 8,5 36,0 80,0 42,0 20,0 3,3 2,0 14,5
06 28,0 10,0 43,0 79,0 41,0 20,0 1,7 2,2 18,0
20,0
07 35,0 16,0 60,0 110,0 52,0 38,0 1,7 3,2 1,5 41,0
08 45,0 17,0 66,0 150,0 70,0 50,0 2,0 3,8 2,0 87,0
09 58,0 27,0 82,0 158,0 58,0 62,0 2,0 3,8 3,8 121,0
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual manufacturer for exact
dimensions.
b
The innermost lip is optional.
c
The values of mass may be higher for some material types. Refer to the individual manufacturer.
d
For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm.
Recovered As supplied
Detail X
Figure 4 — Style C (lipped straight bottle with long body)
Table 4 — Style C
Dimensions are in millimetres
d d d l l l l b S S S
Size l b Mass g
1 2 3 1 2 3 4 l 1 2 3
c
code
Max.
a
Max. Max. ± 10 % ref ref Max. ± 20 ± 20 % ± 30 %
± 10
Min.
± 10 %
%
%
01 28,0 10,0 43,0 99,0 61,0 20,0 1,7 2,2 1,0 24,5
02 35,0 16,0 60,0 130,0 72,0 38,0 20,0 1,7 3,2 1,5 50,0
3,3 20,0
03 45,0 17,0 66,0 171,0 90,0 50,0 2,0 3,8 2,0 103,0
04 58,0 27,0 82,0 213,0 113,0 62,0 37,0 2,0 3,8 3,8 184,0
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual manufacturer for exact
dimensions.
b
The innermost lip is optional.
c
The values of mass may be higher for some material types. Refer to the individual manufacturer.
Recovered As supplied
Figure 5 — Style D (non-lipped straight bottle)
Table 5 — Style D
Dimensions are in millimetres
Size d d d l l l S b
1 2 3 1 2 3 1 Mass g Max.
code
Max. Max. a ± 10 % ref ref ± 20 %
Min.
01 8,0 3,8 16,0 25,4 14,2 6,0 1,3 1,2
02 10,5 5,6 23,0 38,1 22,0 9,5 1,5 3,3
03 14,5 6,6 28,0 52,5 27,0 15,0 1,8 4,3
04 18,0 7,5 31,0 66,0 37,0 18,0 1,8 7,7
05 24,5 8,6 36,0 73,7 42,0 17,0 1,8 13,6
06 28,5 9,9 42,0 97,0 58,0 21,0 2,0 21,7
07 35,5 16,0 51,0 127,0 65,0 41,0 3,2 54,5
08 44,5 20,3 66,0 160,5 91,0 48,0 3,8 105,0
09 57,5 27,0 81,0 210,0 115,0 61,5 4,2 199,0
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the
individual manufacturer for details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual
manufacturer for exact dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
Recovered As supplied
Detail X
Figure 6 — Style E (lipped straight bottle with long tail)
Table 6 — Style E
Dimensions are in millimetres
d d d d l l l l S S S b
Size
1 2 3 4 1 2 3 4 1 2 3 Mass g Max.
code
a
Max. Max. Min. ± 10 % ref ref Max. ± 20 % ± 20 % ± 30 %
Min.
01 12,0 6,5 22,0 22,0 76,0 57,0 3,3
c
1,5
02 13,0 2,0 19,0 6,0 60,0 38,0 4,1
03 15,0 7,5 25,5 25,5 83,0 60,0 4,4
c
19,0 2,5 26,0 7,5 74,0 12,0 45,0 1,0 5,7
05 19,0 8,5 29,0 29,0 89,0 63,0 6,5
1,8 1,1
06 23,0 10,0 34,0 34,0 102,0 73,0 8,0
c
26,0 3,0 34,0 9,5 84,0 51,0 10,0
3,3
08 30,0 11,0 37,0 37,0 108,0 14,0 72,0 2,1 12,0
c
34,0 3,5 43,5 11,5 100,0 12,0 58,0 1,8 10,0
1,7
10 34,0 12,0 43,5 43,5 114,0 15,0 74,0 2,0 14,0
11 41,0 14,5 50,0 50,0 118,0 15,0 73,0 2,3 22,0
12 47,0 18,0 62,5 62,5 121,0 71,0 28,0
1,4
13 60,0 20,0 69,0 69,0 127,0 16,0 67,0 2 2,5 38,0
14 67,0 23,0 81,5 81,5 133,0 69,0 47,0
These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for
details.
a
Shapes made from some material types may be supplied with a reduced d diameter. Refer to the individual manufacturer for exact
dimensions.
b
The values of mass may be higher for some material types. Refer to the individual manufacturer.
c
These sizes have a stepped “as supplied” profile i.e. d is larger than d
3 4.
Recovered As supplied
Detail X
Figure 7 — Style F (lipped right-angle boot)
Table 7 — Style F
Dimensions are in millimetres
Size d d d l l l l l S S S Mass g
1 2 3 1 2 3 4 5 1 2 3
code b
Max.
Max. Max. a ± 20 % ref ref Max. ref ± 20 % ± 20 % ± 30 %
Min.
01 10,5 6,0 24,0 32,0 25,0 19,0 10,0 1,3 0,6 2,2
02 14,0 6,0 30,0 41,0 27,0 20,0 12,0 1,5 0,8 3,3
1,0
03 18,0 7,0 31,0 51,0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.