EN ISO 3451-4:2024
(Main)Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:2024)
Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:2024)
This document specifies methods for determination of the ash of polyamides, both filled and unfilled. It follows the general procedures given in ISO 3451-1.
Kunststoffe - Bestimmung der Asche - Teil 4: Polyamide (ISO 3451-4:2024)
Dieses Dokument legt Verfahren zur Bestimmung der Asche von Polyamiden sowohl mit als auch ohne Füllstoff fest. Es befolgt die in ISO 3451 1 angegebenen allgemeinen Verfahren.
WARNUNG — Dieses Dokument kann gefährliche Chemikalien, Werkstoffe und Verfahren beinhalten. Dieses Dokument beansprucht nicht, die mit dessen Anwendung verbundenen Sicherheitsprobleme zu behandeln. Es liegt in der Verantwortung des Anwenders, angemessene Maßnahmen in Bezug auf den Gesundheits- und Arbeitsschutz zu ergreifen und alle geltenden gesetzlichen Beschränkungen vor der Anwendung zu bestimmen.
Plastiques - Détermination du taux de cendres - Partie 4: Polyamides (ISO 3451-4:2024)
Le présent document spécifie les méthodes de détermination du taux de cendres des polyamides chargés et non chargés. Il suit les modes opératoires généraux indiqués dans l’ISO 3451-1.
Polimerni materiali - Določevanje pepela - 4. del: Poliamidi (ISO 3451-4:2024)
Ta dokument določa metode za ugotavljanje pepela iz poliamidov, tako polnjenih kot nepolnjenih. Upošteva splošne postopke iz standarda ISO 3451-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2024
Polimerni materiali - Določevanje pepela - 4. del: Poliamidi (ISO 3451-4:2024)
Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:2024)
Kunststoffe - Bestimmung der Asche - Teil 4: Polyamide (ISO 3451-4:2024)
Plastiques - Détermination du taux de cendres - Partie 4: Polyamides (ISO 3451-4:2024)
Ta slovenski standard je istoveten z: EN ISO 3451-4:2024
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3451-4
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2024
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 3451-4:2000
English Version
Plastics - Determination of ash - Part 4: Polyamides (ISO
3451-4:2024)
Plastiques - Détermination du taux de cendres - Partie Kunststoffe - Bestimmung der Asche - Teil 4:
4: Polyamides (ISO 3451-4:2024) Polyamide (ISO 3451-4:2024)
This European Standard was approved by CEN on 18 February 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3451-4:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3451-4:2024) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2024, and conflicting national standards
shall be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3451-4:2000.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 3451-4:2024 has been approved by CEN as EN ISO 3451-4:2024 without any
modification.
International
Standard
ISO 3451-4
Third edition
Plastics — Determination of ash —
2024-02
Part 4:
Polyamides
Plastiques — Détermination du taux de cendres —
Partie 4: Polyamides
Reference number
ISO 3451-4:2024(en) © ISO 2024
ISO 3451-4:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 3451-4:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
4.1 General .1
4.2 Unfilled materials .1
4.3 Filled and glass-fibre reinforced materials .2
4.4 Flame-retardant materials reinforced with glass fibre .2
5 Reagents (method C or method A in the presence of DBB) . 2
6 Apparatus . 2
7 Procedure . 3
7.1 General .3
7.2 Test portion .3
7.3 Unfilled materials .3
7.4 Filled and glass-fibre reinforced materials .3
7.5 Materials reinforced with glass fibre containing flame-retardant antimony trioxide
and/or other volatilizable additives .3
8 Expression of results . 4
9 Precision . 4
10 Test report . 5
iii
ISO 3451-4:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 5, Physical-
chemical properties, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC249, Plastics, in accordance with the Agreement on technical cooperation between ISO
and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 3451-4:1998), which has been technically
revised.
The main changes are as follows:
— automatic device method (method D) has been added according to align with the revised ISO 3451-1:2019.
A list of all parts in the ISO 3451 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 3451-4:2024(en)
Plastics — Determination of ash —
Part 4:
Polyamides
WARNING — This document can involve hazardous chemicals, materials and operations. This
document does not purport to address the safety problems associated with its use. It is the
responsibility of the user to establish proper safety and health practices and determine any
applicable regulatory limitations prior to use.
1 Scope
This document specifies methods for determination of the ash of polyamides, both filled and unfilled. It
follows the general procedures given in ISO 3451-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 3451-1:2019, Plastics — Determination of ash — Part 1: General methods
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Principle
4.1 General
For unfilled materials, method A and method D or method C of ISO 3451-1:2019 is used.
For fill
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.