EN ISO 3037:2022
(Main)Corrugated fibreboard - Determination of edgewise crush resistance (non-waxed edge method) (ISO 3037:2022)
Corrugated fibreboard - Determination of edgewise crush resistance (non-waxed edge method) (ISO 3037:2022)
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.
This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard.
It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
Wellpappe - Bestimmung des Kantenstauchwiderstandes (Verfahren für ungewachste Kanten) (ISO 3037:2022)
Dieses Dokument legt ein Verfahren für ungewachste Kanten für die Bestimmung des Kantenstauch-widerstandes von Wellpappe fest. Die Kraft wird in der Richtung der Wellenachse aufgebracht.
Dieses Verfahren ist für einwellige (doppelseitige), zwei- und dreiwellige Wellpappe anwendbar.
Es ist für alle Wellenarten anwendbar, wenn während der Messung kein Beulen und/oder Kippen auftritt. Dieses Verfahren ist auch für Durchschnittsproben anwendbar, die von Wellkisten und anderen verarbeiteten Produkten entnommen wurden.
Carton ondulé - Détermination de la résistance à la compression sur chant (méthode sans enduction de cire) (ISO 3037:2022)
Le présent document spécifie une méthode sans enduction de cire permettant de déterminer la résistance à la compression sur chant du carton ondulé. La force est appliquée dans le sens de l’axe des cannelures.
Cette méthode est applicable au carton ondulé simple cannelure (double face), double cannelure et triple cannelure.
Elle concerne toutes les sortes de cannelures de cartons ondulés lorsque aucun flambage ni aucun basculement ne se produit au cours du mesurage, ainsi aux échantillons pour essai prélevés sur les caisses de carton ondulé et d’autres produits transformés.
Valoviti karton - Določanje robne odpornosti (metoda ECT) (ISO 3037:2022)
Ta dokument določa metodo nevoskanega roba za določanje robne odpornosti valovitega kartona. Sila deluje v smeri osi žlebiča.
Ta metoda se uporablja za enoplasten (dvoslojni), dvoplasten in triplasten valoviti karton.
Uporablja se za vse vrste žlebičev valovitega kartona, če pri merjenju ne pride do uklona in/ali nagiba. Ta metoda se uporablja tudi za preskusne vzorce valovite embalaže in drugih predelanih proizvodov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2023
Nadomešča:
SIST EN ISO 3037:2013
Valoviti karton - Določanje robne odpornosti (metoda ECT) (ISO 3037:2022)
Corrugated fibreboard - Determination of edgewise crush resistance (non-waxed edge
method) (ISO 3037:2022)
Wellpappe - Bestimmung des Kantenstauchwiderstandes (Verfahren für ungewachste
Kanten) (ISO 3037:2022)
Carton ondulé - Détermination de la résistance à la compression sur chant (méthode
sans enduction de cire) (ISO 3037:2022)
Ta slovenski standard je istoveten z: EN ISO 3037:2022
ICS:
85.060 Papir, karton in lepenka Paper and board
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3037
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 85.080.30 Supersedes EN ISO 3037:2013
English Version
Corrugated fibreboard - Determination of edgewise crush
resistance (non-waxed edge method) (ISO 3037:2022)
Carton ondulé - Détermination de la résistance à la Wellpappe - Bestimmung des
compression sur chant (méthode sans enduction de Kantenstauchwiderstandes (Verfahren für
cire) (ISO 3037:2022) ungewachste Kanten) (ISO 3037:2022)
This European Standard was approved by CEN on 25 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3037:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3037:2022) has been prepared by Technical Committee ISO/TC 6 "Paper, board
and pulps" in collaboration with Technical Committee CEN/TC 172 “Pulp, paper and board” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3037:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 3037:2022 has been approved by CEN as EN ISO 3037:2022 without any modification.
INTERNATIONAL ISO
STANDARD 3037
Sixth edition
2022-11
Corrugated fibreboard —
Determination of edgewise crush
resistance (non-waxed edge method)
Carton ondulé — Détermination de la résistance à la compression sur
chant (méthode sans enduction de cire)
Reference number
ISO 3037:2022(E)
ISO 3037:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 3037:2022(E)
Contents Page
Foreword .iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Abbreviated terms . 2
4 Principle . 2
5 Apparatus . 2
6 Sampling . 2
7 Conditioning . 3
8 Preparation of test pieces .3
9 Procedure .4
10 Calculation . 4
11 Precision . 5
12 Test report . 5
Annex A (informative) Examples of suitable cutting devices . 6
Annex B (informative) Precision data . 7
Bibliography . 9
iii
ISO 3037:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee
SC 2, Test methods and quality specifications for paper and board, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 172, Pulp, paper and board, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This sixth edition cancels and replaces the fifth edition (ISO 3037:2013), which has been technically
revised.
The main changes are as follows:
— the title has been changed from "Corrugated fibreboard - Determination of edgewise crush
resistance (unwaxed edge method)" to "Corrugated fibreboard - Determination of edgewise crush
resistance (non-waxed edge method)";
— the introduction has been updated to highlight the impact of edge effects and the incomparability of
different test methods;
— information about the corrugated fibreboard grades has been added to the scope;
— Clause 3 has been updated;
— Clause 6 has been revised;
— Clause 9 has been updated and a constant feed rate has been added;
— Clause 11 has been added to refer to precision data in Annex B;
— Clause 12 has been updated;
— Annex A has been revised;
— the bibliography has been updated.
iv
ISO 3037:2022(E)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
ISO 3037:2022(E)
Introduction
A variety of methods for the determination of edgewise crush resistance are in use in different parts of
the world. These can be classified into four groups as follows:
a) Those in which a carefully cut rectangular test piece is tested without any special treatment or
modification (e.g. this document).
b) Those in which the edges of the test piece to which the force is applied are waxed, to prevent the
test result being influenced by edge effects (e.g. ISO 13821).
c) Those in which the test piece edges are not waxed but the shape of the test piece is such that the
length is substantially reduced at a point midway between the loaded edges, in order to induce the
failure to occur away from those edges (e.g. JIS Z 0403-2).
d) Those in which carefully cut rectangular test pieces are tested with edges clamped to prevent the
result from being influenced by edges effects (e.g. TAPPI T 839).
The dimensions of the test piece vary from on
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.