iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15091:2006/AC:2007

(Corrigendum)

Sanitary tapware - Electronic opening and closing sanitary tapware

Sanitary tapware - Electronic opening and closing sanitary tapware

TC - Table 11, 2nd column, 2nd row - Correction of test pressure

Sanitärarmaturen - Sanitäramaturen mit elektronischer Öffnungs- und Schließfunktion

Robinetterie sanitaire - Robinet sanitaire à ouverture et fermeture électroniques

Sanitarne armature - Elektronsko odpiranje in zapiranje sanitarnih armatur

General Information

Status
Withdrawn
Publication Date
23-Oct-2007
Withdrawal Date
10-Dec-2013
ICS
91.140.70 - Sanitary installations
Technical Committee
CEN/TC 164 - Water supply
Drafting Committee
CEN/TC 164/WG 8 - Sanitary tapware
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
11-Dec-2013
Completion Date
11-Dec-2013
Ref Project
SIST EN 15091:2007/AC:2008 - Sanitary tapware - Electronic opening and closing sanitary tapware

Relations

Replaced By
EN 15091:2013 - Sanitary tapware - Electronic opening and closing sanitary tapware
Effective Date
18-Dec-2013
Corrects
EN 15091:2006 - Sanitary tapware - Electronic opening and closing sanitary tapware
Effective Date
08-Jun-2022

Buy Standard

EN 15091:2007/AC:2008EN 15091:2007/AC:2008
PreviousNext
Corrigendum
EN 15091:2007/AC:2008
English, French and German language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitary tapware - Electronic opening and closing sanitary tapwareSanitarne armature - Elektronsko odpiranje in zapiranje sanitarnih armaturRobinetterie sanitaire - Robinet sanitaire a ouverture et fermeture électroniquesSanitärarmaturen - Sanitäramaturen mit elektronischer Öffnungs- und SchließfunktionTa slovenski standard je istoveten z:EN 15091:2006/AC:2007SIST EN 15091:2007/AC:2008en,fr,de91.140.70Sanitarne napraveSanitary installationsICS:SLOVENSKI
STANDARDSIST EN 15091:2007/AC:200801-januar-2008

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15091:2006/ACOctober 2007Octobre 2007Oktober 2007ICS 91.140.70English versionVersion FrançaiseDeutsche FassungSanitary tapware - Electronic opening and closing sanitary tapwareRobinetterie sanitaire - Robinet sanitaire àouverture et fermeture électroniquesSanitärarmaturen - Sanitäramaturen mitelektronischer Öffnungs- undSchließfunktionThis corrigendum becomes effective on 24 October 2007 for incorporation in the three officiallanguage versions of the EN.Ce corrigendum prendra effet le 24 octobre 2007 pour incorporation dans les trois versionslinguistiques officielles de la EN.Die Berichtigung tritt am 24.Oktober 2007 zur Einarbeitung in die drei offiziellen Sprachfassungen derEN in Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier auxmembres nationaux du CEN.Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind weltweit den nationalen Mitgliedernvon CEN vorbehalten.Ref. No.:EN 15091:2006/AC:2007 D/E/F

English version
In 5.3.4, Table 11, column concerning Type 1, second row, the test pressure for measuring the flow rate of taps for system Type 1 is not convenient.
Replace the test pressure "(0,1 + 0,01) MPa [(1,0 + 0,1 bar)]" with "(0,3 + 0,02) MPa [(3,0 + 0,2 bar)]".
In column 2, row 4, replace "Mpa" with "MPa" to read as follows:
Table 11 — Flow rates and test pressures according to application Supply system Taps for s
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 817:2024(Main)
Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications
SIST EN 817:2024

This document specifies:
a)   the field of application for mechanical mixing valves for use in a supply system of Type 1 (see Figure 1);
b)   the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance, corrosion resistance of the surface of the product, sequence of testing and acoustic characteristics with which sanitary tapware products including their components (flexible hose, pull out spray) need to comply where applicable;
c)   test methods to verify the characteristics.
The tests described in this document are type tests (laboratory tests) and not quality control or factory production control (FPC) tests carried out during manufacture.
This document applies to draw-off taps (mechanical mixing valves) for use with sanitary appliances installed in rooms used for personal hygiene (cloakrooms, bathrooms, etc.) and for food preparation (kitchens), i.e. for use with baths, wash basins, bidets, showers and sinks.
The conditions of use and classifications are given in Table 1.
[Table 1]
Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar].
[Figure 1]
Final materials included in the product are not covered by this document.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15091:2024(Main)
Sanitary tapware - Electronic opening and closing sanitary tapware
SIST EN 15091:2024

The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.
The conditions of use for the supply system type are specified in Table 2:
[Table 2]
Annex B lists possible consequences of using a product outside its recommended operating range.
[Figure 1]
[Figure 2]

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 200:2023(Main)
Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
SIST EN 200:2024

This document specifies:
a)   the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:
1)   a supply system of Type 1 (see Figure 1) with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar];
2)   a supply system of Type 2 (see Figure 2) with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar];
b)   the dimensional, leak tightness, pressure resistance, hydraulic performance, mechanical strength, endurance, corrosion resistance of the surface of the product, sequence of testing and acoustic characteristics with which sanitary tapware products including their components (flexible hose, pullout spray) need to comply where applicable;
c)   test methods to verify the characteristics.
The tests described in this document are type tests (laboratory tests) and not quality control or factory production control (FPC) tests carried out during manufacture.
This document is applicable to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for personal hygiene (cloakrooms, bathrooms etc.) and for food preparation (kitchens), i.e. for use with baths, basins, bidets, showers and sinks.
This document applies to sanitary draw-off taps of nominal size 3/8”, 1/2", 3/4" and 1” (PN 10).
The conditions of use and classifications are given in Table 1.
Table 1 - Conditions of use
[ table not reproduced here ]
[ figure not reporduced here ]
Figure 1- Supply system of Type 1 with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar]
[ figure not reporduced here ]
Figure 2 - Supply system of Type 2 with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar]
NOTE   Components which are part or can be delivered with sanitary tapware products are listed in Annex C.
Final materials included in the product are not covered by this document.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 246:2021(Main)
Sanitary tapware - General specifications for aerators
SIST EN 246:2022

This document specifies:
- the dimensional, mechanical, hydraulic and acoustic characteristics with which sanitary tapware aerators (with and without flow regulation) should comply;
- the procedures for testing these characteristics.
This document is applicable to:
- Sanitary tapware aerators intended to be mounted on tapware used with sanitary appliances in toilets, bathrooms and kitchens (e.g. single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
- Sanitary tapware aerators used under the following pressure and temperature conditions (see Table 1).
[Table 1: Conditions for the use of aerators]
NOTE 1   Sanitary tapware aerators can only be connected downstream of the obturator of the sanitary tapware product.
NOTE 2   For the purposes of brevity, sanitary tapware aerators will be detailed only as aerators in the rest of this document.
NOTE 3   The tests described in this document are type tests (laboratory tests) and not quality control tests carried out during manufacture.
NOTE 4   Aerator swivels are to be tested in combination with a specific aerator only and are therefore considered to be sanitary tapware accessories. (Testing of the stand-alone swivels is therefore not covered by the scope of this document. Where swivels are used they are considered to be part of the tapware constructions, e.g. for bidet taps).

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1287:2017(Main)
Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification
SIST EN 1287:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature - 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilet and cloakrooms) and bathrooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve, controlling a shower, bath, basin and/or, bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 816:2017(Main)
Sanitary tapware - Automatic shut-off valves PN 10
SIST EN 816:2017

This European Standard is applicable to single and mixer taps with automatic shut-off for use with sanitary appliances installed in washrooms.
It does not apply to urinal or WC flushing valves or valves which open automatically.
The purpose of this standard is to specify the marking, identification, chemical/hygiene, dimensional, leaktightness, pressure resistance, hydraulic, mechanical endurance, and acoustical characteristics of automatic shut-off tapware.
The tests described in all the standard are type tests (laboratory tests) and not quality control tests carried out during manufacture
The following conditions of pressure and temperature apply:
Table 1 - Conditions for the use of self closing tapware
(The pressures given are flow pressures)

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1111:2017(Main)
Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
SIST EN 1111:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature approximately 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilets and cloakrooms) and bath rooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve controlling a shower, bath, basin and/or bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1113:2015(Main)
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
SIST EN 1113:2015

This European Standard specifies:
-   the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply;
-   the procedures for testing these characteristics.
This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers.
This European Standard applies to shower hoses connected downstream of the obturator of the tapware.
Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard.
Details of pressures and temperatures are given in Table 1.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16146:2012+A1:2014(Main)
Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
SIST EN 16146:2013+A1:2015

This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard.
This European Standard specifies:
-   the dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets shall comply;
-   the procedures for testing these characteristics.
Details of pressures and temperatures are given in Table 1.
(...)

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16145:2012(Main)
Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification
SIST EN 16145:2013

This European Standard specifies:
-   the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply;
-   the procedures for testing these characteristics.
It applies to extractable outlets made from any material which is intended for equipping and supplementing sanitary tapware for sinks and wash-basins used for culinary or ablutionary purposes. Such extractable outlets shall only be connected downstream of the obturator of the tapware.
Extractable outlets with total closing device fitted after the obturator of the tapware are not covered by this standard. Such products will be tested in accordance with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
The conditions of use and classification are specified in Table 1.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day