iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 932-6:1999

(Main)

Tests for general properties of aggregates - Part 6: Definitions of repeatability and reproducibility

Tests for general properties of aggregates - Part 6: Definitions of repeatability and reproducibility

This European Standard gives definitions of repeatability and reproducibility adapted form ISO 5725-1 to the specific situation of sampling and testing aggregates. These adjustments have been made because test portions or test specimens of aggregates are usually not identical to each other as specified in ISO 5725-1.

Prüfverfahren für allgemeine Eigenschaften von Gesteinskörnungen - Teil 6: Definitionen von Wiederholpräzision und Vergleichpräzision

Diese Europäische Norm definiert Begriffe fu(r Wiederholpra(zision und Vergleichpra(zision, angepaßt von ISO 5725-1 and die spezifische Situation der Probenahme und Prüfung von Gesteinskörnungen. Die Anpassungen wurden durchgefu(hrt, da in Abweichung zur Festlegung in ISO 5725-1 Meßproben oder Einzelmeßproben von Gesteinskörnungen u(blicherweise nicht identisch sind.

Essais pour déterminer les propriétés générales des granulats - Partie 6: Définitions de la répétabilité et de la reproductibilité

La présente norme européenne donne les définitions de la répétabilité et de la reproductibilité, adaptées de l'ISO 5725-1 pour le cas spécifique de l'échantillonnage et des essais de granulats. Cette adaptation a été faite du fait que les prises d'essai et les éprouvettes de granulats ne sont généralement pas identiques ` celles spécifiées dans l'ISO 5725-1.

Preskusi splošnih lastnosti agregatov - 6. del: Definicije ponovljivosti in primerljivosti

General Information

Status
Published
Publication Date
18-May-1999
Withdrawal Date
30-Nov-2003
ICS
01.040.91 - Construction materials and building (Vocabularies)
91.100.15 - Mineral materials and products
Technical Committee
CEN/TC 154 - Aggregates
Drafting Committee
CEN/TC 154/SC 6 - Test methods
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
21-Oct-2020
Ref Project
SIST EN 932-6:1999 - Tests for general properties of aggregates - Part 6: Definitions of repeatability and reproducibility

Relations

Child
EN 932-5:1999 - Tests for general properties of aggregates - Part 5: Common equipment and calibration
Effective Date
22-Dec-2008

Buy Standard

EN 932-6:1999EN 932-6:1999
PreviousNext
Standard
EN 932-6:1999
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskusi splošnih lastnosti agregatov - 6. del: Definicije ponovljivosti in primerljivostiPrüfverfahren für allgemeine Eigenschaften von Gesteinskörnungen - Teil 6: Definitionen von Wiederholpräzision und VergleichpräzisionEssais pour déterminer les propriétés générales des granulats - Partie 6: Définitions de la répétabilité et de la reproductibilitéTests for general properties of aggregates - Part 6: Definitions of repeatability and reproducibility91.100.1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12670:2019(Main)
Natural stone - Terminology
SIST EN 12670:2019

This document defines the recommended terminology covering scientific and technical terms, test methods, products, and the classification of Natural Stones. This document does not cover roofing slate, for roofing slate see EN 12326-1 and EN 12326-2.

  • Standard
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12440:2017(Main)
Natural stone - Denomination criteria
SIST EN 12440:2018

This European Standard establishes the criteria for the designation of natural stone from raw material to finished products.

  • Standard
    106 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14618:2009(Main)
Agglomerated stone - Terminology and classification
SIST EN 14618:2009

This document specifies the terminology and classification of the agglomerated stone products. Agglomerated stone products are industrial products mainly made of hydraulic cement, resin or mixture of both, stones and other additions. They are industrially manufactured in geometrical shapes at fixed plants by moulding techniques. They are put on the market in the form of rough blocks, rough slabs, slabs, tiles, dimensional stone works, and any other cut to size products.
All other agglomerated stones products not intended to be used for flooring, wall finishes and assimilated uses (like drainage channels, structural elements, etc.) are excluded from the field of this standard.
This European Standard is not applicable to terrazzo tiles covered by EN 13748-1 [1] and EN 13748-2 [2].

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15167-1:2006(Main)
Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria
SIST EN 15167-1:2006

This European Standard specifies requirements for the chemical and physical properties as well as quality control procedures for ground granulated blastfurnace slag for use as a type II addition in the production of concrete, including in particular cast-in-situ or prefabricated structural concrete conforming to EN 206-1. Ground granulated blastfurnace slag conforming to this European Standard may also be used in mortars and grouts.
Ground granulated blastfurnace slag containing any added materials other than grinding aids, is not within the scope of this European Standard. It is also not within the scope of this European Standard to specify provisions governing the practical application of ground granulated blastfurnace slag in the production of concrete, mortar or grout, i.e. requirements concerning composition, mixing, placing, curing etc. As regards such provisions, reference should be made to other European or national standards, such as EN 206-1.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12299:2024(Main)
Railway applications - Ride comfort for passengers - Measurement and evaluation
SIST EN 12299:2024

The purpose of this document is to provide methods for quantifying the ride comfort of a passenger in a rail vehicle in response to the track sections it is operated over.
The methods aim to quantify the effects of vehicle body motions on ride comfort and to make the assessment of passenger comfort predictable, repeatable, objective and meaningful.
The methods and comfort scales are validated for people of good health.
This document applies to passengers in rail vehicles operating on heavy rail networks.
This document applies to measurements of motions. It also applies to simulated motions. Guidance is provided on:
-   which method described within the document should be used for different scenarios;
-   typical values for different comfort levels;
-   the application of simulation.
This document excludes health and safety issues, non-passenger carrying vehicles, vehicle homologation and safety, limit values, motion sickness, discomfort caused by accelerating and braking, design guidelines and measurement technology.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-4:2024(Main)
Paints and varnishes - Wettability - Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension (ISO 19403-4:2024)
kSIST FprEN ISO 19403-4:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids from an interfacial tension with optical methods. The method can be applied for the characterization of liquid coating materials, especially if drying effects occur during alternative measurement. If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17966:2024(Main)
Fire protection equipment - Carbon dioxide extinguishing systems for use on premises - Design and installation (ISO 6183:2022, modified)
SIST EN 17966:2024

This document specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of fixed carbon dioxide firefighting systems in buildings, plants or other structures. It is not applicable to extinguishing systems on ships, in aircraft, on vehicles or on mobile fire appliances, or to below ground systems in the mining industry; nor does it apply to carbon dioxide pre-inerting systems.
Design of systems where unclosable opening(s) of the protected volume exceed a specified area and where the opening(s) can be subject to the effect of wind is not specified, although general guidance on the procedure to be followed in such cases is given (see 7.4.3.2).

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TR 15235:2024(Main)
Preparation of steel substrates before application of paints and related products - Collected information on the effect of levels of water-soluble salt contamination (ISO/TR 15235:2001)
kSIST-TP FprCEN ISO/TR 15235:2024

This Technical Report provides information on the effect of water-soluble chloride and sulfate contamination levels on steel surfaces, before the application of paint or related products to surfaces prepared in accordance with standard mechanical or blast-cleaning surface preparation methods.
NOTE The tolerance for water-soluble salt contamination may be different for different paint types.
This information may be used when evaluating the adequacy of surface preparation prior to painting.
This document is concerned only with measured levels of salt contamination based upon either laboratory or field testing. The levels of soluble chloride and sulfate discussed in this document are to be compared using soluble surface densities of the species as determined after extraction in accordance with ISO 8502-6 (the Bresle method), or other methods giving equivalent results. Total soluble-salt contamination may be determined by conductometric testing, but such testing will not determine the nature and concentration of the specific salts present, e.g. whether chloride or sulfate is present, or its concentration.
This document does not define specific levels of cleanliness or methods of salt removal.

  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 509:2024(Main)
Decorative fuel-effect gas appliances
kSIST FprEN 509:2024

This document specifies the requirements and test methods for the construction, safety, and marking of decorative fuel effect gas appliances not exceeding a nominal heat input of 20 kW (based on the net calorific value), thereafter referred to as appliances.
This document is applicable to appliances that are designed to simulate a solid fuel fire and incorporate a natural draught burner with or without an ignition burner, that uses one or more combustible gases of the three gas families at the pressures stated in EN 437:2021. The appliances are for decorative purposes only and are not heating appliances.
This document is applicable to type BAS, as described in 4.2, decorative fuel effect gas appliances that are designed to be installed within a non-combustible builder's opening or a non-combustible fireplace recess.
NOTE 1   This document specifies special national conditions in Annex C for appliances of category I2E+, marketed in Belgium.
NOTE 2   This document specifies special A-deviations in Annex D for appliances in Switzerland which require additional requirements for subclauses 6.6 and 6.7.
This document includes additional requirements for Type BBS appliances which are specified in Annex F.
In addition, this document is applicable to decorative fuel-effect gas appliances that are designed to be installed under a non-combustible canopy which is independent or integral with a flue box, for which additional requirements are specified in Annex A.
The use of toxic gases is not covered.
This document is not applicable to:
-   catalytic combustion appliances;
-   appliances in which the supply of combustion air and/or the evacuation of products of combustion is achieved by mechanical means.
NOTE 3   Requirements concerning the rational use of energy have not been included in this document, because the appliances are for decorative purposes.

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day