EN ISO 15245-1:2001
(Main)Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification (ISO 15245-1:2001)
Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification (ISO 15245-1:2001)
This International Standard specifies definitions, dimensions and tolerances of parallel screw threads of nominal diameter 30 mm (designated M30), 25 mm (designated M25) and 18 mm (designated M18), for the connection of valves to medical and industrial gas cylinders. This standard does not cover the connection requirements for: - mechanical tightness; - gas tightness; - capability of repeated assembly and dismounting operation. Note: This aspect is covered in ISO 13341.
Ortsbewegliche Gasflaschen - Zylindrische Gewinde für den Anschluss von Ventilen an Gasflaschen - Teil 1: Spezifikation (ISO 15245-1:2001)
Dieser Teil von ISO 15245 legt Begriffe, Maße und Toleranzen für zylindrische Gewinde mit einem Nenndurchmesser von 30 mm (Bezeichnung M30), 25 mm (Bezeichnung M25) und 18 mm (Bezeichnung M18) für den Anschluss von Ventilen an Gasflaschen für den medizinischen und industriellen Gebrauch fest.
Dieser Teil von ISO 15245 enthält keine Anforderungen an die Verbindung hinsichtlich
¾ der mechanischer Festigkeit;
¾ der Gasdichtheit;
¾ der Fähigkeit, eine Reihe von Montagen und Demontagen unbeschadet zu überstehen ).
Bouteilles à gaz - Filetages parallèles pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécifications (ISO 15245-1:2001)
La présente partie de l'ISO 15245 spécifie les définitions, les dimensions et les tolérances des filetages parallèles d'un diamètre nominal de 30 mm (désigné 30P), de 25 mm (désigné 25P) et de 18 mm (désigné 18P) raccordant les robinets sur les bouteilles à gaz médicales ou industrielles. La présente partie de l'ISO 15245 ne comporte pas d'exigences de raccordement pour : - la résistance mécanique; - l'étanchéité au gaz; - la capacité à répéter les opérations de montage et de démontage.
Plinske jeklenke - Cilindrični navoji za priključitev ventilov na jeklenke - 1. del: Specifikacija (ISO 15245-1:2001)
Ta del standarda ISO 15245 določa definicije, mere in odstopanja cilindričnih navojev nominalnega premera 30 mm (označeni s 30P), 25 mm (označeni s 25P) in18 mm (označeni z 18P) za priključitev ventilov na jeklenke za medicinske in industrijske pline. Ta del standarda ISO 15245 ne določa zahtev za priključitev za:
– mehansko trdnost;
– neprepustnost za pline;
– zmožnost večkratnega sestavljanja in razstavljanja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15245-1:2002
01-maj-2002
3OLQVNHMHNOHQNH&LOLQGULþQLQDYRML]DSULNOMXþLWHYYHQWLORYQDMHNOHQNHGHO
6SHFLILNDFLMD ,62
Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1:
Specification (ISO 15245-1:2001)
Ortsbewegliche Gasflaschen - Zylindrische Gewinde für den Anschluss von Ventilen an
Gasflaschen - Teil 1: Spezifikation (ISO 15245-1:2001)
Bouteilles a gaz - Filetages paralleles pour le raccordement des robinets sur les
bouteilles a gaz - Partie 1: Spécifications (ISO 15245-1:2001)
Ta slovenski standard je istoveten z: EN ISO 15245-1:2001
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN ISO 15245-1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15245-1:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 15245-1:2002
EUROPEAN STANDARD
EN ISO 15245-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2001
ICS 23.020.30
English version
Gas cylinders - Parallel threads for connection of valves to gas
cylinders - Part 1: Specification (ISO 15245-1:2001)
Bouteilles à gaz - Filetages parallèles pour le raccordement Ortsbewegliche Gasflaschen - Zylindrische Gewinde für
des robinets sur les bouteilles à gaz - Partie 1: den Anschluss von Ventilen an Gasflaschen - Teil 1:
Spécifications (ISO 15245-1:2001) Spezifikation (ISO 15245-1:2001)
This European Standard was approved by CEN on 5 October 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15245-1:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15245-1:2002
EN ISO 15245-1:2001 (E)
CORRECTED 2002-10-09
Foreword
This document (EN ISO 15245-1:2001) has been prepared by Technical Committee ISO/TC
58 "Gas cylinders" in collaboration with Technical Committee CEN/TC 23 "Transportable gas
cylinders", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by April 2002, and conflicting national
standards shall be withdrawn at the latest by April 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of ISO 15245-1:2001 has been approved by CEN as EN ISO 15245-1:2001 without
any modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15245-1:2002
EN ISO 15245-1:2001 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 286-1 1988 ISO system of limits and fits - EN 20286-1 1993
Part 1: Bases of tolerances,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.