iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 11403-2:2022

(Main)

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)

Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)

This document specifies test procedures for the acquisition and presentation of multipoint data on the following thermal and processing properties of plastics:
—    enthalpy/temperature curve;
—    linear-expansion/temperature curve;
—    melt shear viscosity.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 2: Thermische und Verarbeitungseigenschaften (ISO 11403-2:2022)

Dieses Dokument legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunkt-Kennwerten für folgende thermische Eigenschaften und Verarbeitungseigenschaften von Kunststoffen fest:
   Enthalpie-Temperatur-Diagramm;
   Längenausdehnung-Temperatur-Diagramm;
   Schmelz-Scherviskosität.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 2: Propriétés thermiques et caractéristiques relatives à la mise en oeuvre (ISO 11403-2:2022)

Le présent document spécifie des modes opératoires d’essai en vue de l’acquisition et de la présentation de données multiples relatives aux propriétés thermiques et de mise en œuvre suivantes des plastiques:
—    courbe enthalpie/température;
—    courbe dilatation linéique/température;
—    viscosité en cisaillement du matériau fondu.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 2. del: Toplotne lastnosti in lastnosti pri predelavi (ISO 11403-2:2022)

Ta dokument določa preskusne postopke za pridobitev in predstavitev podatkov, dobljenih pri različnih pogojih,
o naslednjih toplotnih lastnostih in lastnostih pri predelavi za polimerne materiale:
– krivulja entalpije/temperature;
– krivulja linearnega raztezanja/temperature;
– strižna viskoznost taline.

General Information

Status
Published
Publication Date
02-Aug-2022
ICS
83.080.01 - Plastics in general
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
03-Aug-2022
Completion Date
03-Aug-2022
Ref Project
SIST EN ISO 11403-2:2022 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)

Relations

Replaces
EN ISO 11403-2:2012 - Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
Effective Date
10-Aug-2022

Buy Standard

EN ISO 11403-2:2022EN ISO 11403-2:2022
PreviousNext
Standard
EN ISO 11403-2:2022
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-2:2022
01-september-2022
Nadomešča:
SIST EN ISO 11403-2:2014
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 2. del: Toplotne lastnosti in lastnosti pri predelavi (ISO 11403-
2:2022)
Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal
and processing properties (ISO 11403-2:2022)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
2: Thermische und Verarbeitungseigenschaften (ISO 11403-2:2022)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 2:
Propriétés thermiques et caractéristiques relatives à la mise en oeuvre (ISO 11403-
2:2022)
Ta slovenski standard je istoveten z: EN ISO 11403-2:2022
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11403-2:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 11403-2:2022


EN ISO 11403-2
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2022
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 11403-2:2012
English Version

Plastics - Acquisition and presentation of comparable
multipoint data - Part 2: Thermal and processing
properties (ISO 11403-2:2022)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von
multiples comparables - Partie 2: Propriétés vergleichbaren Vielpunkt-Kennwerten - Teil 2:
thermiques et caractéristiques relatives à la mise en Thermische und Verarbeitungseigenschaften (ISO
oeuvre (ISO 11403-2:2022) 11403-2:2022)
This European Standard was approved by CEN on 23 July 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-2:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11403-2:2022
EN ISO 11403-2:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11403-2:2022
EN ISO 11403-2:2022 (E)
European foreword
This document (EN ISO 11403-2:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2023, and conflicting national standards
shall be withdrawn at the latest by February 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-2:2012.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 22007-1:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)
SIST EN ISO 22007-1:2024

This document describes the background to methods for the determination of the thermal conductivity and thermal diffusivity of polymeric materials. Different techniques are available for these measurements and some can be better suited than others for a particular type, state and form of material. This document provides a broad overview of these techniques. Standards specific to these techniques, as referenced in this document, are used to carry out the actual test method.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22007-4:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 4: Light flash method (ISO 22007-4:2024)
SIST EN ISO 22007-4:2024

This document specifies a method for the determination of the thermal diffusivity of a thin solid disc of plastics in the thickness direction by the light flash method. This method is based upon the measurement of the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front face.
The method is applicable to homogeneous solid plastics as well as composites having an isotropic or orthotropic structure. In general, it covers materials having a thermal diffusivity, α, in the range 1 × 10−7 m2⋅s−1 < α < 1 × 10−4 m2⋅s−1. Measurements can be carried out in gaseous and vacuum environments over a temperature range from −100 °C to +400 °C.
NOTE          For inhomogeneous specimens, the measured values can be specimen thickness dependent.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8256:2023(Main)
Plastics - Determination of tensile-impact strength (ISO 8256:2023)
SIST EN ISO 8256:2024

1.1     This document specifies two methods (method A and method B) for the determination of the tensile-impact strength of plastics under defined conditions. The tests can be described as tensile tests at relatively high strain rates. These methods can be used for rigid materials (as defined in ISO 472), but are especially useful for materials too flexible or too thin to be tested with impact tests conforming to the ISO 179 series or ISO 180.
1.2     These methods are used for investigating the behaviour of specified specimens under specified impact velocities, and for estimating the brittleness or the toughness of specimens within the limitations inherent in the test conditions.
1.3     These methods are applicable both to specimens prepared from moulding materials and to specimens taken from finished or semi-finished products (for example mouldings, laminates, or extruded or cast sheets).
1.4     Results obtained by testing moulded specimens of different dimensions are not necessarily the same. Equally, it is possible that specimens cut from moulded products will not give the same results as specimens of the same dimensions moulded directly from the material. Test results obtained from specimens prepared from moulding compounds cannot be applied directly to mouldings of any given shape, because values may depend on the design of the moulding and the moulding conditions. Results obtained by method A and method B can or can not be comparable.
1.5     These methods are not suitable for use as a source of data for design calculations on components. Information on the typical behaviour of a material can be obtained, however, by testing different types of test specimen prepared under different conditions, and by testing at different temperatures. The two different methods are suitable for production control as well as for quality control.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20753:2023(Main)
Plastics - Test specimens (ISO 20753:2023)
SIST EN ISO 20753:2024

This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles. It compiles the designations and dimensions of test specimens used for the acquisition of comparable data and of other frequently used specimens.
The following types of test specimen are specified:
A            Tensile specimen, multipurpose or reduced-scale
B            Bar specimen
C            Small tensile specimen
D            Square plate specimen
F            Rectangular plate specimen
NOTE    If a particular type of test specimen is not mentioned in this document, this does not mean that there is any intention to exclude the use of the specimen. Additional specimen types can be added in future if they are commonly used.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 61:2023(Main)
Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:2023)
SIST EN ISO 61:2023

This document specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material that cannot be poured from a funnel of specified design.
NOTE            For a method of determining the apparent density of loose moulding material that can be poured from a specified funnel, see ISO 60.
This document is applicable to loose moulding materials such as slice, granular or powder.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24187:2023(Main)
Principles for the analysis of microplastics present in the environment (ISO 24187:2023)
SIST EN ISO 24187:2023

This document describes the principles to be followed in the analysis of microplastics in various environmental matrices. This includes the unique particle size classification of plastics, the use of certain apparatus with regard to sampling, sample preparation, and the determination of representative sample quantities.
The purpose of this document is to specify minimum requirements until specific standards for the different case situations are available. This is important to ensure that the development of the specific standards is done on a consistent basis to ensure that comparison or correlation of results is possible.
This document does not include requirements for monitoring actions.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13927:2023(Main)
Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2023)
SIST EN ISO 13927:2023

This document specifies a method suitable for the production control or product development purposes for assessing the heat release rate of essentially flat products exposed in the horizontal orientation to controlled levels of radiant heating with an external igniter. The heat release rate is determined by the use of a thermopile instead of the more accurate oxygen consumption techniques. The time to ignition and sustained flaming are also measured in this test. The mass loss of the test specimen can also be measured optionally.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20200:2023(Main)
Plastics - Determination of the degree of disintegration of plastic materials under composting conditions in a laboratory-scale test (ISO 20200:2023)
SIST EN ISO 20200:2023

This document specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6186:2023(Main)
Plastics - Determination of pourability (ISO 6186:2023)
SIST EN ISO 6186:2023

This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6603-2:2023(Main)
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing (ISO 6603-2:2023)
SIST EN ISO 6603-2:2023

This document specifies a test method for the determination of puncture impact properties of rigid plastics, in the form of flat specimens, using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominal constant striker velocity, is necessary for detailed characterization of the impact behaviour.
The test method is applicable to specimens with a thickness between 1 mm to 4 mm.
The method is suitable for use with the following types of material:
—    rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and sheets;
—    rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and laminates;
—    fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or multi-directional reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
The method is also applicable to specimens which are either moulded or machined from finished products, laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and surfaces as well as the test conditions are the same. In particular, results determined on specimens of different thickness cannot be compared with one another (see Annex E). Comprehensive evaluation of the reaction to impact stress can be obtained by determinations made as a function of impact velocity and temperature for different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken from finished products (see above) for tests by this method.
Test data developed by this method is not intended to be used for design calculations. However, information on the typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see Annex D) by varying the thickness (see Annex E) and by testing specimens prepared under different conditions.
It is not the purpose of this document to give an interpretation of the mechanism occurring on every particular point of the force-deflection diagram. These interpretations are a task for scientific research.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day