Plastics - Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion (ISO 11357-5:2013)

ISO 11357-5:2013 specifies a method for the determination of reaction temperatures and times, enthalpies of reaction, and degrees of conversion using differential scanning calorimetry (DSC).
The method applies to monomers, prepolymers, and polymers in the solid or liquid state. The material can contain fillers and/or initiators in the solid or liquid state.

Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 5: Bestimmung von charakteristischen Reaktionstemperaturen und -zeiten, Reaktionsenthalpie und Umsatz (ISO 11357-5:2013)

Dieser Teil von ISO 11357 legt ein Verfahren für die Bestimmung von Reaktionstemperaturen und -zeiten, Reaktionsenthalpien und Umsätzen mithilfe der dynamischen Differenz-Thermoanalyse (DSC) fest.
Das Verfahren gilt für Monomere, Vorpolymere und Polymere im festen oder flüssigen Zustand. Das Material kann Füllstoffe und/oder Initiatoren im festen oder flüssigen Zustand enthalten.

Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 5: Détermination des températures et temps caractéristiques de la courbe de réaction, de l'enthalpie de réaction et du degré de transformation (ISO 11357-5:2013)

L'ISO 11357-5:2013 spécifie une méthode de détermination des températures et temps de réaction, des enthalpies de réaction et degrés de transformation, en utilisant une analyse calorimétrique différentielle (DSC).
La méthode est applicable aux monomères, prépolymères et polymères à l'état solide ou liquide. Le matériau peut contenir des charges et/ou initiateurs à l'état solide ou liquide.

Polimerni materiali - Diferenčna dinamična kalorimetrija (DSC) - 5. del: Ugotavljanje karakterističnih reakcijskih temperatur in časov, entalpije reakcije in stopnje pretvorbe (ISO 11357-5:2013)

Standard EN-ISO 11357-5 določa metodo za ugotavljanje karakterističnih reakcijskih temperatur in časov, entalpije reakcije in stopnje pretvorbe z diferenčno dinamično kalorimetrijo (DSC). Metoda se nanaša na monomere, prepolimere in polimere v tekoči ali trdni obliki. Material lahko vsebuje polnila in/ali iniciatorje v tekoči ali trdni obliki.

General Information

Status
Published
Publication Date
25-Mar-2014
Withdrawal Date
29-Sep-2014
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
26-Mar-2014
Due Date
17-May-2015
Completion Date
26-Mar-2014

Buy Standard

Standard
EN ISO 11357-5:2014
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN ISO 11357-5:2014
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11357-5:2014
01-maj-2014
3ROLPHUQLPDWHULDOL'LIHUHQþQDGLQDPLþQDNDORULPHWULMD '6& GHO
8JRWDYOMDQMHNDUDNWHULVWLþQLKUHDNFLMVNLKWHPSHUDWXULQþDVRYHQWDOSLMHUHDNFLMHLQ
VWRSQMHSUHWYRUEH ,62
Plastics - Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic
reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
(ISO 11357-5:2013)
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 5: Bestimmung von
charakteristischen Reaktionstemperaturen und -zeiten, Reaktionsenthalpie und Umsatz
(ISO 11357-5:2013)
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 5: Détermination des
températures et temps caractéristiques de la courbe de réaction, de l'enthalpie de
réaction et du degré de transformation (ISO 11357-5:2013)
Ta slovenski standard je istoveten z: EN ISO 11357-5:2014
ICS:
17.200.10 Toplota. Kalorimetrija Heat. Calorimetry
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11357-5:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11357-5:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 11357-5:2014

EUROPEAN STANDARD
EN ISO 11357-5

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2014
ICS 83.080.01
English Version
Plastics - Differential scanning calorimetry (DSC) - Part 5:
Determination of characteristic reaction-curve temperatures and
times, enthalpy of reaction and degree of conversion (ISO
11357-5:2013)
Plastiques - Analyse calorimétrique différentielle (DSC) - Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) -
Partie 5: Détermination des températures et temps Teil 5: Bestimmung von charakteristischen
caractéristiques de la courbe de réaction, de l'enthalpie de Reaktionstemperaturen und -zeiten, Reaktionsenthalpie
réaction et du degré de transformation (ISO 11357-5:2013) und Umsatz (ISO 11357-5:2013)
This European Standard was approved by CEN on 6 March 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11357-5:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11357-5:2014
EN ISO 11357-5:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11357-5:2014
EN ISO 11357-5:2014 (E)
Foreword
The text of ISO 11357-5:2013 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 11357-5:2014 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2014, and conflicting national standards shall be
withdrawn at the latest by September 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland,
...

SLOVENSKI STANDARD
kSIST FprEN ISO 11357-5:2014
01-februar-2014
3ROLPHUQLPDWHULDOL'LIHUHQþQDGLQDPLþQDNDORULPHWULMD '6& GHO
8JRWDYOMDQMHNDUDNWHULVWLþQLKUHDNFLMVNLKWHPSHUDWXULQþDVRYHQWDOSLMHUHDNFLMHLQ
VWRSQMHSUHWYRUEH ,62
Plastics - Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic
reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
(ISO 11357-5:2013)
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 5: Bestimmung von
charakteristischen Reaktionstemperaturen und -zeiten, Reaktionsenthalpie und Umsatz
(ISO 11357-5:2013)
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 5: Détermination des
températures et temps caractéristiques de la courbe de réaction, de l'enthalpie de
réaction et du degré de transformation (ISO 11357-5:2013)
Ta slovenski standard je istoveten z: FprEN ISO 11357-5
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
kSIST FprEN ISO 11357-5:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

kSIST FprEN ISO 11357-5:2014

---------------------- Page: 2 ----------------------

kSIST FprEN ISO 11357-5:2014


EUROPEAN STANDARD
FINAL DRAFT
FprEN ISO 11357-5
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2013
ICS 83.080.01
English Version
Plastics - Differential scanning calorimetry (DSC) - Part 5:
Determination of characteristic reaction-curve temperatures and
times, enthalpy of reaction and degree of conversion (ISO
11357-5:2013)
Plastiques - Analyse calorimétrique différentielle (DSC) - Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC)
Partie 5: Détermination des températures et temps - Teil 5: Bestimmung von charakteristischen
caractéristiques de la courbe de réaction, de l'enthalpie de Reaktionstemperaturen und -zeiten, Reaktionsenthalpie
réaction et du degré de transformation (ISO 11357-5:2013) und Umsatz (ISO 11357-5:2013)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 249.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprEN ISO 11357-5:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

kSIST FprEN ISO 11357-5:2014
FprEN ISO 11357-5:2013 (E)
Contents Page
Foreword .3


2

---------------------- Page: 4 ----------------------

kSIST FprEN ISO 11357-5:2014
FprEN ISO 11357-5:2013 (E)
Foreword
The text of ISO 11357-5:2013 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as FprEN ISO 11357-5:2013 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This document is currently submitted to the Unique Acceptance Procedure.
Endorsement notice
The text of ISO 11357-5:2013 has been approved by CEN as FprEN ISO 11357-5:2013 without any
modification.

3

---------------------- Page: 5 ----------------------

kSIST FprEN ISO 11357-5:2014

---------------------- Page: 6 ----------------------

kSIST Fpr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.