CEN/TS 764-6:2004

Pressure equipment - Part 6: Structure and content of operating instructions

This part six of this document identifies the requirements for operating instructions which accompany the pressure equipment when it is placed on the market. Operating instructions shall contain the necessary safety information covering installation including assembling, putting into service and maintenance.

Druckgeräte - Teil 6: Aufbau und Inhalt einer Betriebsanleitung

Equipements sous pression - Partie 6 : Structure et contenu des instructions de service

Tlačna oprema - 6. del: Oblika in vsebina navodil za obratovanje

General Information

• Status: Withdrawn
• Publication Date: 10-Aug-2004
• Withdrawal Date: 09-Oct-2012
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: CEN/TC 54 - Unfired pressure vessels
• Drafting Committee: CEN/TC 54/WG 54 - D - Manufacture
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 10-Oct-2012
• Completion Date: 10-Oct-2012
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST-TS CEN/TS 764-6:2004 - Pressure equipment - Part 6: Structure and content of operating instructions

Relations

• Replaced By: CEN/TR 764-6:2012 - Pressure equipment - Part 6: Structure and content of operating instructions
• Effective Date: 16-Apr-2011

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 764-6:2004
01-november-2004
Tlačna oprema - 6. del: Oblika in vsebina navodil za obratovanje
Pressure equipment - Part 6: Structure and content of operating instructions
Druckgeräte - Teil 6: Aufbau und Inhalt einer Betriebsanleitung
Equipements sous pression - Partie 6 : Structure et contenu des instructions de service
Ta slovenski standard je istoveten z: CEN/TS 764-6:2004
ICS:
23.020.32 Tlačne posode Pressure vessels
SIST-TS CEN/TS 764-6:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 764-6:2004

---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 764-6:2004
TECHNICAL SPECIFICATION
CEN/TS 764-6
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
August 2004
ICS 23.020.30
English version
Pressure equipment - Part 6: Structure and content of operating
instructions
Equipements sous pression - Partie 6 : Structure et Druckgeräte - Teil 6: Aufbau und Inhalt einer
contenu des instructions de service Betriebsanleitung
This Technical Specification (CEN/TS) was approved by CEN on 30 April 2004 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 764-6:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 764-6:2004
CEN/TS 764-6:2004 (E)
Contents Page
Foreword.3
1 Scope .4
2 General.4
3 Hazard analysis.4
3.1 General.4
3.2 Possible hazards for all pressure equipment and assemblies .4
3.3 Possible hazards for specific pressure equipment and assemblies.5
3.3.1 Fired or otherwise treated pressure equipment and assemblies .5
3.3.2 Piping .6
4 Content of operating instructions.6
4.1 General.6
4.1.1 Introduction.6
4.1.2 Information on the data plate .6
4.1.3 Information in operating instructions.6
4.2 Transportation and erection or installation (mounting) .7
4.3 Putting into service.7
4.4 Use/Operation .
...

SLOVENSKI STANDARD
SIST-TS CEN/TS 764-6:2004
01-november-2004
7ODþQDRSUHPDGHO2EOLNDLQYVHELQDQDYRGLO]DREUDWRYDQMH
Pressure equipment - Part 6: Structure and content of operating instructions
Druckgeräte - Teil 6: Aufbau und Inhalt einer Betriebsanleitung
Equipements sous pression - Partie 6 : Structure et contenu des instructions de service
Ta slovenski standard je istoveten z: CEN/TS 764-6:2004
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST-TS CEN/TS 764-6:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 764-6:2004

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 764-6:2004
TECHNICAL SPECIFICATION
CEN/TS 764-6
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
August 2004
ICS 23.020.30
English version
Pressure equipment - Part 6: Structure and content of operating
instructions
Equipements sous pression - Partie 6 : Structure et Druckgeräte - Teil 6: Aufbau und Inhalt einer
contenu des instructions de service Betriebsanleitung
This Technical Specification (CEN/TS) was approved by CEN on 30 April 2004 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 764-6:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 764-6:2004
CEN/TS 764-6:2004 (E)
Contents Page
Foreword.3
1 Scope .4
2 General.4
3 Hazard analysis.4
3.1 General.4
3.2 Possible hazards for all pressure equipment and assemblies .4
3.3 Possible hazards for specific pressure equipment and assemblies.5
3.3.1 Fired or otherwise treated pressure equipment and assemblies .5
3.3.2 Piping .6
4 Content of operating instructions.6
4.1 General.6
4.1.1 Introduction.6
4.1.2 Information on the data plate .6
4.1.3 Information in operating instructions.6
4.2 Transportation and erection or installation (mounting) .7
4.3 Putting into service.
...