CEN/TC 54/WG 54 - D - Manufacture

This part six of EN 764 is a Technical Report and as such is a generic document that identifies requirements for operating instructions which accompany the pressure equipment when it is placed on the market. It only provides general statements and thus does not claim to give presumption of conformity to the essential safety requirements of the Pressure Equipment Directive (PED).
Operating instructions contain the necessary safety information covering installation including assembling, putting into service and maintenance. For specific items of pressure equipment or assemblies, more detailed requirements on the content of operating instructions can be found in specific standards such as EN 13445 Unfired pressure vessels, EN 13480 Industrial piping, EN 12952 Water-tube boilers and auxiliary installations, or EN 12953 Shell boilers.

Revise clause 15

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, requirements for permanent joints other than welding, production tests, forming requirements, heat treatment, repairs and finishing operations.

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, requirements for permanent joints other than welding, production tests, forming requirements, heat treatment, repairs and finishing operations.

Amends Clause 7.4 "Qualification of welders and welding operators"

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, requirements for permanent joints other than welding, production tests, forming requirements, heat treatment, repairs and finishing operations.

Approval of permanent joining without welding

2010-03-31 EMA: Former standard reference EN 13445-4:2005/prA4 changed to prA1 following e-mail from secretary sent to tcminares on 2010-03-30, in order to avoid amendments published out of order.
2010-01-15 EMA: Tolerance of 9 months before Formal Vote requested through resolution 613 taken on 2009-11-26.
2009-11-27 SJ: This amendment was originally amending the 2002 version. The 2002 version has been consolidated (main + all adopted amendments). prA4 has not yet been adopted. It will now amend the consolidated version of 2009 (00054100)
2009-08-03 EMA: Amendment replaced by EN 13445-4:2009.
2013: Originator of XML version: first setup pilot of CCMC in 2012

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of
steels, including their connections to non-pressure parts. It specifies requirements for material traceability,
manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs
and finishing operations.

This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of
aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under
EN 13445:2009 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full
cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to
or a revision of this European Standard.

This part six of this document identifies the requirements for operating instructions which accompany the pressure equipment when it is placed on the market. Operating instructions shall contain the necessary safety information covering installation including assembling, putting into service and maintenance.

Amendment for production test plates and updating of welding standards.

This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure ves-sels under EN 13445:2002 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE    Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this European Standard.

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations.
This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3:2002.