prEN 14576
(Main)Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking
- Abstract
This document specifies a test method for screening the resistance of polymeric geosynthetic barriers to stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other polymeric geosynthetic barriers which have a partially crystalline structure.
NOTE The described method is suitable for conformance testing of smooth surfaced (non-textured) geosynthetic barriers. However the resistance to stress cracking of the resin used in the manufacture of structured surface materials can be evaluated by carrying out the test on a plaque formed from the relevant resin (see 4.5) or, where structuring is carried out as a separate processing step, on a preformed smooth surface geosynthetic barrier, the test can be performed on the intermediate smooth material.
The data are suitable for screening and determination of conformity but not for deriving performance data such as lifetime, unless supported by further evidence.
- Status
- Not Published
- Publication Date
- 23-Apr-2028
- Technical Committee
- CEN/TC 189 - Geotextiles and geotextile-related products
- Drafting Committee
- CEN/TC 189/WG 5 - Durability
- Current Stage
- 4020 - Submission to enquiry - Enquiry
- Start Date
- 29-Oct-2026
- Due Date
- 11-Jan-2027
- Completion Date
- 29-Oct-2026
Relations
- Effective Date
- 18-Feb-2026
Get Certified
Connect with accredited certification bodies for this standard

Control Union Certifications
Global certification for agriculture and sustainability.
Hohenstein Institut
Textile testing and certification.

Bureau Veritas Bangladesh
Bureau Veritas certification services in Bangladesh.
Sponsored listings
Frequently Asked Questions
prEN 14576 is a draft published by the European Committee for Standardization (CEN). Its full title is "Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking". This standard covers: This document specifies a test method for screening the resistance of polymeric geosynthetic barriers to stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other polymeric geosynthetic barriers which have a partially crystalline structure. NOTE The described method is suitable for conformance testing of smooth surfaced (non-textured) geosynthetic barriers. However the resistance to stress cracking of the resin used in the manufacture of structured surface materials can be evaluated by carrying out the test on a plaque formed from the relevant resin (see 4.5) or, where structuring is carried out as a separate processing step, on a preformed smooth surface geosynthetic barrier, the test can be performed on the intermediate smooth material. The data are suitable for screening and determination of conformity but not for deriving performance data such as lifetime, unless supported by further evidence.
This document specifies a test method for screening the resistance of polymeric geosynthetic barriers to stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other polymeric geosynthetic barriers which have a partially crystalline structure. NOTE The described method is suitable for conformance testing of smooth surfaced (non-textured) geosynthetic barriers. However the resistance to stress cracking of the resin used in the manufacture of structured surface materials can be evaluated by carrying out the test on a plaque formed from the relevant resin (see 4.5) or, where structuring is carried out as a separate processing step, on a preformed smooth surface geosynthetic barrier, the test can be performed on the intermediate smooth material. The data are suitable for screening and determination of conformity but not for deriving performance data such as lifetime, unless supported by further evidence.
prEN 14576 is classified under the following ICS (International Classification for Standards) categories: 59.080.70 - Geotextiles. The ICS classification helps identify the subject area and facilitates finding related standards.
prEN 14576 has the following relationships with other standards: It is inter standard links to EN 14576:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
prEN 14576 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2027
Geosintetika - Preskusna metoda za ugotavljanje odpornosti polimernih
geosintetičnih pregrad proti pokanju zaradi napetostne korozije v okolju
Geosynthetics - Test method for determining the resistance of polymeric geosynthetic
barriers to environmental stress cracking
Geokunststoffe - Prüfverfahren zur Bestimmung der Beständigkeit von geosynthetischen
Kunststoffdichtungsbahnen gegen umweltbedingte Spannungsrissbildung
Géosynthétiques - Méthode d'essai pour la détermination de la résistance des barrières
géosynthétiques polymériques à la fissuration sous contrainte environnementale
Ta slovenski standard je istoveten z: prEN 14576
ICS:
59.080.70 Geotekstilije Geotextiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2026
ICS Will supersede EN 14576:2005
English Version
Geosynthetics - Test method for determining the
resistance of polymeric geosynthetic barriers to
environmental stress cracking
Géosynthétiques - Méthode d'essai pour la Geokunststoffe - Prüfverfahren zur Bestimmung der
détermination de la résistance des barrières Beständigkeit von geosynthetischen
géosynthétiques polymériques à la fissuration sous Kunststoffdichtungsbahnen gegen umweltbedingte
contrainte environnementale Spannungsrissbildung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 189.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14576:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 4
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 General requirements and procedure . 5
5.1 Apparatus . 5
5.1.1 Blanking die . 5
5.1.2 Notching device . 7
5.1.3 Stress cracking apparatus . 7
5.1.4 Compression moulding press . 8
5.1.5 Compression moulding die . 9
5.2 Test temperatures . 9
5.3 Reagent . 9
5.4 Test duration . 9
5.5 Compression moulding procedure . 9
5.6 Specimens . 9
5.7 Test procedure . 10
6 Test report . 11
Annex A (informative) Potential supply sources for the equipment. 12
Bibliography . 13
European foreword
This document (prEN 14576:2026) has been prepared by Technical Committee CEN/TC 189
“Geosynthetics”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14576:2005.
This document includes the following significant technical changes with respect to EN 14576:2005:
— update of Subclause 5.3 regarding the surface-active agent;
— editorial revision of the document.
Introduction
Stress cracking is a phenomenon observed in most thermoplastic materials. It is defined as internal or
external cracking of the material caused by tensile stresses less than the short time mechanical strength
of the material. Stress cracking may limit the durability of e.g. thermoplastic pipes and geosynthetic
barriers. In addition to the influence of the stress, stress cracking is accelerated by elevated temperature
and the presence of certain molecular species, such as surfactants, in the surrounding environment.
The ability of a material to withstand stress cracking is known as its stress crack resistance. Stress crack
resistance is measured by the time required to failure when a specimen of the material is immersed in a
particular medium at elevated temperature while under a defined stress. Stress crack resistance is
primarily a function of the resin (thermoplastic raw material) type but may be adversely influenced by
the geosynthetic barrier manufacturing process, particularly by certain procedures for friction
enhancement. The so-called “bent strip” test described in ASTM D 1693 was used as a screening test for
many years. However, this method has been found to provide misleading results due to relaxation of the
specimen and reduction of the stress level during increased testing periods. In consequence, the “bent
strip” test has been unable to differentiate the performance of improved resins requiring longer testing
periods.
To meet the requirement to accurately quantify and differentiate the performance of modern resins, the
Geosynthetics Institute (formerly Geosynthetics Research Institute) developed an alternative method,
GRI-GM5. The GRI method is frequently referred to as the “notched constant tensile load” (NCTL) test, as
the apparatus used ensures a constant level of stress in the specimen throughout the test and the
specimen is notched to provide a concentration point for stress and failure. The NCTL test is now used
extensively throughout the geosynthetic barrier industry.
The NCTL test can be performed under two separate procedures that are described in GRI-GM5 (a) and
5 (b). In the procedure GRI-GM5 (a), the so-called “full curve test”, specimens are immersed in the test
liquid at a range of stresses, typically from 20 % to 65 % of the yield strength of the material. The time to
failure and the failure mode (brittle or ductile) is recorded at each level of stress. Failure time is plotted
against stress. Typically, the resulting curve will show an abrupt change in slope at a point that coincides
with a change in failure mode. The time at which this occurs is recorded as the “transition time”.
The second variant of the test, GRI-GM5 (b), which is simpler and quicker to perform, is known as the
“single point” test. In this case, the specimens are tested at 30 % of the measured yield stress of the
material at normal room temperature, and the time to failure is recorded. The procedure described in
this document is based on GRI-GM5 (b).
1 Scope
This document specifies a test method for screening the resistance of polymeric geosynthetic barriers to
stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other
polymeric geosynthetic barriers which have a partially crystalline structure.
NOTE The described method is suitable for conformance testing of smooth surfaced (non-textured)
geosynthetic barriers. However, the resistance to stress cracking of the resin used in the manufacture of structured
surface materials can be evaluated by carrying out the test on a plaque formed from the relevant resin (see 5.5) or,
where structuring is carried out as a separate processing step, on a preformed smooth surface geosynthetic barrier,
the test can be performed on the intermediate smooth material.
The data are suitable for screening and determination of conformity but not for deriving performance
data such as lifetime, unless supported by further evidence.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 3696, Water for analytical laboratory use — Specification and test methods (ISO 3696)
EN ISO 9862, Geosynthetics — Sampling and preparation of test specimens (ISO 9862)
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
4 Principle
Dumbbell shaped notched test specimens cut from the geosynthetic barrier are subjected to a constant
tensile load in the presence of a surface-active agent at an elevated temperature. The time to failure of
each test specimen is recorded.
5 General requirements and procedure
5.1 Apparatus
5.1.1 Blanking die
A die suitable for cutting test specimens to the dimensions and tolerances is shown in Figure 1 a).
The length of the specimen can be changed to suit the design of the test apparatus. However, there should
be a constant width neck section at least 13 mm long. The width of the neck section should be 3,17 mm.
The tab widths may be enlarged to accommodate grommets of different sizes with which to attach hooks
for the purp
...



