EN 13743:2017
(Main)Safety requirements for coated abrasive products
Safety requirements for coated abrasive products
This European Standard is applicable to the following coated abrasive products and a combination of coated and non-woven abrasive products: flap wheels, flap discs, vulcanised fibre discs and spindle mounted flap wheels. It also applies to back-up pads for vulcanised fibre discs. These products are manufactured using the following abrasive grains: aluminium oxide, silicon carbide, diamond, or CBN.
This European Standard specifies requirements and/or measures for removal or reduction of hazards resulting from the design and application of the coated abrasive products and clamping devices.
This European Standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4 of this standard.
This European Standard does not apply to abrasive products entirely of non-woven web.
Sicherheitsanforderungen für Schleifmittel auf Unterlagen
Prescriptions de sécurité pour les produits abrasifs appliqués
La présente Norme européenne est applicable aux produits abrasifs appliqués suivants et à une combinaison de produits abrasifs appliqués et non tissés : roues à lamelles, disques à lamelles, disques en fibre vulcanisée et roues à lamelles sur tige. Elle s’applique également aux supports de disques en fibre vulcanisée. Ces produits sont fabriqués en utilisant les grains abrasifs suivants : oxyde d'aluminium, carbure de silicium, diamant ou CBN.
La présente Norme européenne spécifie les prescriptions et/ou les mesures pour la suppression ou la réduction des phénomènes dangereux résultant de la conception et de l’utilisation des produits abrasifs appliqués et des dispositifs de fixation.
La présente Norme européenne contient également les modes opératoires et les essais pour la vérification de la conformité aux exigences aussi bien que les informations de sécurité pour l’utilisation, que le fabricant doit fournir à l’utilisateur.
Les phénomènes dangereux à prendre en considération sont donnés à l’Article 4 de la présente norme.
La présente Norme européenne ne s’applique pas aux produits abrasifs entièrement en toile non tissée.
Varnostne zahteve za brusna sredstva na podlagah
Kot v obstoječem standardu EN 13743): ta evropski standard se uporablja za naslednja brusna sredstva na podlagah: pahljačasta kolesa, pahljačaste kolute, kolute z vulkaniziranimi vlakni in pahljačasta kolesa na vretenu. Uporablja se tudi za varnostne blazinice kolutov z vulkaniziranimi vlakni. Ta evropski standard določa zahteve in/ali ukrepe za preprečevanje ali zmanjševanje tveganj, ki izhajajo iz oblikovanja in uporabe brusnih sredstev na podlagah in vpenjalnih naprav. Ta evropski standard vsebuje tudi postopke in preskuse za preverjanje skladnosti z zahtevami ter varnostne napotke za uporabo, ki jih uporabniku ponuja proizvajalec. Nevarnosti, ki jih je treba upoštevati, so navedene v točki 4 tega standarda. Ta evropski standard se ne uporablja za netkana mrežna brusilna sredstva, vezana brusilna sredstva in superabrazivne izdelke.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varnostne zahteve za brusna sredstva na podlagahSicherheitsanforderungen für Schleifmittel auf UnterlagenPrescriptions de sécurité pour les produits abrasifs appliquésSafety requirements for coated abrasive products25.100.70BrusivaAbrasivesICS:Ta slovenski standard je istoveten z:EN 13743:2017SIST EN 13743:2017en,fr,de01-marec-2017SIST EN 13743:2017SLOVENSKI
STANDARDSIST EN 13743:20091DGRPHãþD
SIST EN 13743:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13743
January
t r s y ICS
t wä s r rä y r Supersedes EN
s u y v uã t r r {English Version
Safety requirements for coated abrasive products Prescriptions de sécurité pour les produits abrasifs appliqués
Sicherheitsanforderungen für Schleifmittel auf Unterlagen This European Standard was approved by CEN on
s v November
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u y v uã t r s y ESIST EN 13743:2017
EN 13743:2017 (E) 2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 3.1 General . 5 3.2 Grinding machines . 5 3.3 Type of application . 6 3.3.1 General . 6 3.4 Symbols . 7 4 List of significant hazards . 7 5 Safety requirements . 8 5.1 General requirements . 8 5.1.1 General . 8 5.1.2 Sequence of maximum operating speeds . 8 5.2 Safety factors. 9 5.2.1 Safety factors for flap wheels, flap discs and vulcanised fibre discs . 9 5.2.2 Safety factors for spindle mounted flap whee
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.