EN ISO 6520-2:2001

Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure (ISO 6520-2:2001)

This European Standard collects and classifies the possible imperfections in welds made with pressure.  A uniform designation is specified. Only the type, shape and dimensions of the different imperfections caused by welding with pressure are included. Metallurgical deviations are not taken into account. Imperfections produced other than by the welding operation, for example additional stresses, loads or environmental factors are not covered by this standard.
Information concerning the consequences of the mentioned imperfections and the use of particular structures is not given because this depends on the specific requirements of the joint.

Schweißen und verwandte Prozeße - Einteilung von geometrischen Unregelmäßigkeiten an Metallen - Teil 2: Preßschweissungen (ISO 6520-2:2001)

In dieser Norm sind die an Preßschweißverbindungen möglichen Unregelmäßigkeiten zusammengestellt und eingeteilt. Hierfür sind einheitliche Benennungen festgelegt. Die Norm umfaßt nur Art, Form und Lage von Unregelmäßigkeiten, die durch Preßschweißen verursacht wurden. Metallurgische Veränderungen bleiben unberücksichtigt. Unregelmäßigkeiten, die nicht durch das Schweißen entstanden sind, z.B. zusätzliche Spannungen, Belastungen oder Umwelteinflüsse, sind nicht Bestandteil dieser Norm.
Es wird nichts darüber ausgesagt, wie die Unregelmäßigkeiten im Einzelfall zu beurteilen sind, da dies von den jeweiligen Anforderungen an die Schweißverbindungen abhängt.

Soudage et techniques connexes - Classification des défauts géométriques dans les soudures des matières métalliques - Partie 2: Soudage avec pression (ISO 6520-2:2001)

La présente norme réunit et classifie les défauts éventuels des soudures par pression. On y spécifie une désignation uniforme. Elle ne comprend que le type, la forme et les dimensions des différents défauts dus au soudage par pression et ne tient pas compte des différences métallurgiques. Les défauts provoqués par des opérations autres que le soudage, par exemple des contraintes ou des sollicitations supplémentaires ou des facteurs liés à l'environnement, ne sont pas couverts par la présente norme.
Aucune information concernant les conséquences des défauts mentionnés et l'utilisation de structures particulières n'est donnée, ces informations dépendant des exigences spécifiques qui s'appliquent au joint.

Varjenje in sorodni postopki - Klasifikacija geometrijskih nepopolnosti v kovinskih materialih - 2. del: Varjenje s pritiskom (ISO 6520-2:2001)

General Information

• Status: Withdrawn
• Publication Date: 14-Dec-2001
• Withdrawal Date: 06-Aug-2013
• ICS: 25.160 - Welding, brazing and soldering
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121 - Welding
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 07-Aug-2013
• Completion Date: 07-Aug-2013
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN ISO 6520-2:2002 - Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure (ISO 6520-2:2001)

Relations

• Replaced By: EN ISO 6520-2:2013 - Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure (ISO 6520-2:2013)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varjenje in sorodni postopki - Klasifikacija geometrijskih nepopolnosti v kovinskih materialih - 2. del: Varjenje s pritiskom (ISO 6520-2:2001)Schweißen und verwandte Prozeße - Einteilung von geometrischen Unregelmäßigkeiten an Metallen - Teil 2: Preßschweissungen (ISO 6520-2:2001)Soudage et techniques connexes - Classification des défauts géométriques dans les soudures des matieres métalliques - Partie 2: Soudage avec pression (ISO 6520-2:2001)Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure (ISO 6520-2:2001)25.160.10Varilni postopki in varjenjeWelding processesICS:Ta slovenski standard je istoveten z:EN ISO 6520-2:2001SIST EN ISO 6520-2:2002en01-maj-2002SIST EN ISO 6520-2:2002SLOVENSKI
STANDARDSIST EN 26520:19951DGRPHãþD



SIST EN ISO 6520-2:2002



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 6520-2December 2001ICS 25.160.00English versionWelding and allied processes - Classification of geometricimperfections in metallic materials - Part 2: Welding withpressure (ISO 6520-2:2001)Soudage et techniques connexes - Classification desdéfauts géométriques dans les soudures des matièresmétalliques - Partie 2: Soudage avec pression (ISO 6520-2:2001)Schweißen und verwandte Prozeße - Einteilung vongeometrischen Unregelmäßigkeiten an Metallen - Teil 2:Preßschweissungen (ISO 6520-2:2001)This European Standard was approved by CEN on 13 April 2000.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 6520-2:2001 ESIST EN ISO 6520-2:2002



EN ISO 6520-2:2001 (E)2ContentsPageForeword.31Scope.42Normative references.43Classification.4Annex A (informative) Imperfections and welding processes.25Bibliography.28SIST EN ISO 6520-2:2002



EN ISO 6520-2:2001 (E)3ForewordThe text of EN ISO 6520-2:2001 has been prepared by Technical CommitteeCEN/TC 121 "Welding", the secretariat of which is held by DS, in collaboration withTechnical Committee ISO/TC 44 "Welding and allied processes".This European Standard shall be given the status of a national standard, either bypublication of an identical text or by endorsement, at the latest by June 2002, andconflicting national standards shall be withdrawn at the latest by June 2002.According to the CEN/CENELEC Internal Regulations, the national standardsorganizations of the following countries are bound to implement this EuropeanStandard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany,Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN ISO 6520-2:2002



EN ISO 6520-2:2001 (E)41ScopeThis European Standard collects and classifies the possible imperfections in weldsmade with pressure.
A uniform designation is specified. Only the type, shape anddimensions of the different imperfections caused by welding with pressure areincluded. Metallurgical deviations are not taken into account. Imperfections producedother than by the welding operation, for example additional stresses, loads orenvironmental factors are not covered by this standard.Information concerning the consequences of the mentioned imperfections and the useof particular structures is not given because this depends
...