iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14598-3:2005

(Main)

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

This part of prEN 14598 specifies the requirements for physical and chemical properties of Sheet moulding Compounds (SMC) and Bulk Moulding Compound (BMC) and compression or injection moulded specimens. The selection in this part is limited to those materials the composition and properties of which are significantly different.
Furthermore the selection is limited to those materials which are of more general technical and / or economical importance.
The properties which are used for the characterization of the moulding compounds, the test methods and the test conditions are based on part 2 of this standard. The list of properties is selected, initially, from those general test methods found in ISO 10350-1, Plastics - Acquisition and presentation of comparable single-point data - Part 1 : Moulding materials.
The moulding compounds are divided into types corresponding to their composition and properties. The designation of the types of moulding compounds is based on part 1 "Designation" of this standard.

Verstärkte härtbare Formmassen - Spezifikation für Harzmatten (SMC) und faserverstärkte Pressmassen (BMC) - Teil 3: Spezifische Anforderungen

In diesem Teil von EN 14598 werden die Anforderungen an physikalische und chemische Eigenschaften von
Harzmatten (SMC) und faserverstärkten Pressmassen (BMC) und daraus formgepressten oder spritzge-
gossenen Probekörpern festgelegt. Die Auswahl ist in diesem Teil auf solche Formmassen begrenzt, deren
Zusammensetzung und Eigenschaften sich deutlich unterscheiden.
Außerdem ist die Auswahl auf Formmassen begrenzt, die von allgemeinerer technischer und/oder
wirtschaftlicher Bedeutung sind.
Die Eigenschaften, die zur Charakterisierung der Formmassen dienen, die Prüfverfahren und die Prüf-
bedingungen beruhen auf Teil 2 dieses Dokuments. Die Liste der Eigenschaften wurde ursprünglich aus den
in EN ISO 10350-2, Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-
fibre-reinforced plastics, angeführten allgemeinen Prüfverfahren ausgewählt.
Die Formmassen sind nach deren Zusammensetzung und Eigenschaften in Typen eingeteilt. Die Bezeich-
nung der Formmassetypen beruht auf Teil 1 :Bezeichnungin dieses Dokuments.

Mélanges à mouler thermodurcissables renforcés - Spécification pour mats préimprégnés (SMC) et mélanges à mouler en masse (BMC) - Partie 3 : Exigences spécifiques

La présente partie du prEN 14598 spécifie les exigences relatives aux propriétés physiques et chimiques des mats préimprégnés (SMC) et des mélanges à mouler en masse (BMC), ainsi que des échantillons moulés par compression ou par injection. Dans la présente partie, la sélection des matériaux est limitée aux matériaux dont la composition et les propriétés sont significativement différents.
De plus, la sélection est limitée aux matériaux qui sont d'une importance technique et/ou économique plus générale.
Les propriétés qui sont utilisées pour la caractérisation des mélanges à mouler, les méthodes d'essai et les conditions d'essai sont fondées sur la partie 2 de la présente norme. La liste des propriétés est sélectionnée, initialement, à partir des méthodes d'essai générales indiquées dans l'ISO 10350-1, Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 1 : Matériaux pour moulage.
Les mélanges à mouler sont divisés en types correspondant à leur composition et à leurs propriétés. La désignation des types de mélanges à mouler est fondée sur la Partie 1 " Désignation " de la présente norme.

Ojačene duromerne mase za oblikovanje - Specifikacija za oblikovalne mase v ploščah (SMC) in oblikovalne mase v testastem stanju (BMC) - 3. del: Posebne zahteve

General Information

Status
Published
Publication Date
26-Apr-2005
Withdrawal Date
30-Oct-2005
ICS
83.120 - Reinforced plastics
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249/SC 2/WG 3 - Prepregs - Composites with random reinforcements
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
03-Mar-2024
Completion Date
03-Mar-2024
Ref Project
SIST EN 14598-3:2005 - Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements

Buy Standard

EN 14598-3:2005EN 14598-3:2005
PreviousNext
Standard
EN 14598-3:2005
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14598-3:2005
01-julij-2005
2MDþHQHGXURPHUQHPDVH]DREOLNRYDQMH6SHFLILNDFLMD]DREOLNRYDOQHPDVHY
SORãþDK 60& LQREOLNRYDOQHPDVHYWHVWDVWHPVWDQMX %0& GHO3RVHEQH
]DKWHYH
Reinforced thermosetting moulding compounds - Specification for Sheet Moulding
Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
Verstärkte härtbare Formmassen - Spezifikation für Harzmatten (SMC) und
faserverstärkte Pressmassen (BMC) - Teil 3: Spezifische Anforderungen
Mélanges a mouler thermodurcissables renforcés - Spécification pour mats
préimprégnés (SMC) et mélanges a mouler en masse (BMC) - Partie 3 : Exigences
spécifiques
Ta slovenski standard je istoveten z: EN 14598-3:2005
ICS:
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN 14598-3:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14598-3:2005

---------------------- Page: 2 ----------------------

SIST EN 14598-3:2005
EUROPEAN STANDARD
EN 14598-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2005
ICS 83.120
English version
Reinforced thermosetting moulding compounds - Specification
for Sheet Moulding Compound (SMC) and Bulk Moulding
Compound (BMC) - Part 3: Specific requirements
Mélanges à mouler thermodurcissables renforcés - Verstärkte härtbare Formmassen - Spezifikation für
Spécification pour mats préimprégnés (SMC) et mélanges Harzmatten (SMC) und faserverstärkte Pressmassen
à mouler en masse (BMC) - Partie 3 : Exigences (BMC) - Teil 3: Spezifische Anforderungen
spécifiques
This European Standard was approved by CEN on 21 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14598-3:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 14598-3:2005
EN 14598-3:2005 (E)
Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Requirements.5
4.1 General.5
4.2 Type and content of filler/reinforcement.5
4.3 Recycling .5
4.4 Property data.5
Bibliography .20


2

---------------------- Page: 4 ----------------------

SIST EN 14598-3:2005
EN 14598-3:2005 (E)
Foreword
This document (EN 14598-3:2005) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the
secretariat of which is held by
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 14126:2023(Main)
Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction (ISO 14126:2023)
SIST EN ISO 14126:2023

1.1 This document specifies methods for determining the compressive properties, in directions
parallel to the plane of lamination, of fibre-reinforced plastic composites, based on thermosetting or
thermoplastic matrices. The compressive properties are of interest for specifications and qualitycontrol
purposes. The test specimens are machined from a flat test plate, or from suitable finished or
semi-finished products.
1.2 Two loading methods and two types of specimen are described.
The loading methods are:
— Method 1: provides shear loading of the specimen (gauge length unsupported)
— Method 2: provides combined loading of the specimen (gauge length unsupported)
NOTE For tabbed specimens loaded using method 2, load is transferred through a combination of endloading
and shear-loading through the tabs.
The specimen designs are:
— Type A specimen: rectangular cross-section, fixed thickness, end-tabbed (mainly for aerospace
style preimpregnates (~ 0,125 mm ply thickness)
— Type B specimen: rectangular cross-section, range of thicknesses, untabbed or end-tabbed, two
specimen sizes are available (B1 and B2).
The Type A specimen is used for unidirectionally or biaxially reinforced materials tested in the
fibre direction, where the fibres are normally either aligned continuous or aligned long (>7,5 mm)
discontinuous. The Type B1 and B2 specimens are used for multi-directional aligned; mat, fabric and
other multi-directionally reinforced materials where the fibre structure is more complex and/or
coarser.
1.3 This document gives criteria for checking that the combination of test method and specimen
design result in valid failures. It is noted that alternative test method/specimen combinations will not
necessarily give the same result.
1.4 The methods specify required dimensions for the specimen. Tests carried out on specimens of
other dimensions, or on specimens that are prepared under different conditions, can produce results
that are not comparable. Other factors, such as the speed of testing, the support fixture used and the
conditioning of the specimens, can influence the results.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1172:2023(Main)
Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content using calcination methods (ISO 1172:2023)
SIST EN ISO 1172:2023

This document specifies two calcination methods for the determination of the textile glass and mineral filler content of glass-reinforced plastics:
—     Method A: for the determination of the textile glass content when no mineral fillers are present.
—     Method B: for the determination of the textile-glass and mineral-filler content when both components are present.
This document is applicable to the following types of material:
—     prepregs made from yarns, rovings, tapes or fabrics;
—     SMC, BMC and DMC moulding compounds;
—     textile-glass-reinforced thermoplastic moulding materials and granules;
—     filled or unfilled textile-glass laminates made with thermosetting or thermoplastic resins.
The methods do not apply to the following types of reinforced plastic:
—     those containing reinforcements other than textile glass;
—     those containing materials which do not completely burn off at the test temperature (for example, those based on silicone resin);
—     those containing mineral fillers which degrade at temperatures below the minimum calcination temperature.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 527-4:2023(Main)
Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:2023)
SIST EN ISO 527-4:2023

This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
NOTE 1   Unidirectional reinforced materials are covered by ISO 527-5.
The methods are used to investigate the tensile behaviour of the test specimens and for determining the tensile strength, tensile modulus, Poisson's ratios and other aspects of the tensile stress-strain relationship under the defined conditions.
The test method is suitable for use with the following materials:
—    fibre-reinforced thermosetting and thermoplastic composites incorporating non-unidirectional reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combinations of such reinforcements, hybrids, rovings, short or milled fibres or preimpregnated materials (prepregs);
NOTE 2   Injection moulded specimens are covered by ISO 527-2.
—    combinations of the above with unidirectional reinforcements and multidirectional reinforced materials constructed from unidirectional layers, provided such laminates are symmetrical;
NOTE 3   Materials with completely or mainly unidirectional reinforcements are covered by ISO 527-5.
—    finished products made from materials mentioned above.
The reinforcement fibres covered include glass fibres, carbon fibres, aramid fibres and other similar fibres.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 527-5:2021(Main)
Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2021)
SIST EN ISO 527-5:2022

This document specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
NOTE      Isotropic and orthotropic reinforced materials are covered by ISO 527-4.
The methods are used to investigate the tensile behaviour of the test specimens and for determining the tensile strength, tensile modulus, Poisson's ratios and other aspects of the tensile stress-strain relationship under the conditions defined.
The test method is suitable for all polymer matrix systems reinforced with unidirectional fibres and which meet the requirements, including failure mode, set out in this document.
The method is suitable for composites with either thermoplastic or thermosetting matrices, including preimpregnated materials (prepregs). The reinforcements covered include carbon fibres, glass fibres, aramid fibres and other similar fibres. The reinforcement geometries covered include unidirectional (i.e. completely aligned) fibres and rovings and unidirectional fabrics and tapes.
The method is not normally suitable for multidirectional materials composed of several unidirectional layers at different angles (see ISO 527-4).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10352:2020(Main)
Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area and fibre mass per unit area (ISO 10352:2020)
SIST EN ISO 10352:2020

This document specifies a method for the determination of the mass per unit area. It also specifies five methods (Method A to Method E) for the determination of the fibre mass per unit area of moulding compounds and prepregs. The five methods are as follows:
—     Method A: Extraction by Soxhlet;
—     Method B: Extraction by immersion in solvent in a beaker;
—     Method C: Decomposition by loss ignition;
—     Method D: Extraction by wet combustion;
—     Method E: Method by calculation.
This document is applicable to the following types of materials:
—     moulding compound and preimpregnated unidirectional sheet, tape, fabric and mats;
—     prepregs in which any type of reinforcement (aramid, carbon, glass, etc.) and any type of matrix (thermosetting or thermoplastic) has been used.
Typically, reinforcement fibres are coated with sizing or finishes. These normally dissolve with the resin and are, therefore, included in the resin content.
This document is not applicable to the following types of prepregs:
—     those containing reinforcements which are soluble (or partly soluble) in the solvents used to dissolve the resin.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10350-2:2020(Main)
Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2020)
SIST EN ISO 10350-2:2020

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets.
This document applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional).
ISO 10350-1 deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20337:2019(Main)
Fibre-reinforced plastic composites - Shear test method using a shear frame for the determination of the in-plane shear stress/shear strain response and shear modulus (ISO 20337:2018)
SIST EN ISO 20337:2019

This document specifies a method using a shear test apparatus for measuring the in-plane shear stress/shear strain response, shear modulus and shear strength of continuous-fibre-reinforced plastic composite materials with fibre orientations of 0° and 0°/90°.
This method is applicable to thermoset and thermoplastic matrix laminates made from unidirectional layers/non-woven fabrics and/or fabrics including unidirectional fabrics, with the fibres oriented at 0° and 0°/90° to the specimen axis, where the lay-up is symmetrical and balanced about the specimen mid-plane.
The method is suitable for determining shear properties in both the linear and nonlinear load-deformation range even at shear strains greater than 5 %.
Short and long fibre-reinforced plastic composites can also be tested using this document.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17129:2018(Main)
Continuous-fibre-reinforced plastic composites - Pultruded unidirectional rods - Determination of tensile properties in parallel to the fibre direction
SIST EN 17129:2019

This document specifies a method for determining the tensile properties of pultruded, unidirectional rods made from continuous fibre-reinforced plastic composites, in parallel to fibre direction.
It is applicable to pultruded rods which diameters are preferably ranging from 3 mm to 20 mm.
This method is suitable for use with continuous-fibre-reinforced plastic composites made from carbon fibres and glass fibres.
This method is suitable for use with all polymer matrix systems reinforced with unidirectional fibres having a cylindrical shape.
This method is not intended to be used for testing specimens such as tubes or yarns already covered by other test methods.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 59:2016(Main)
Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester
SIST EN 59:2016

This European Standard specifies a method for determining the indentation hardness of glass reinforced plastics materials by means of a Barcol hardness tester.
The Barcol hardness tester is a portable device which can be used with a stand. This method is suitable for testing the indentation hardness of individual test specimens or finished products for production control purposes.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16245-2:2013(Main)
Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
SIST EN 16245-2:2013

This European Standard specifies the minimum information to be declared for resins, curing systems, additives and modifiers to be used for the manufacturing of composites products.
These specific declaration requirements are in addition to the general requirements given in EN 16245-1.
This document includes requirements for the Certificate of Analysis (CoA). The purpose of the CoA is to verify that material properties and quality conforms to the declared values.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day