EN 1402-7:2003
(Main)Unshaped refractory products - Part 7: Tests on pre-formed shapes
Unshaped refractory products - Part 7: Tests on pre-formed shapes
This European standard specifies methods for the testing of as-delivered pre-formed shapes. It applies to shapes fabricated from dense and insulating castables and mouldable materials (plastics and ramming mixes) as defined in ENV 1402-1. Note: Acceptance values for the individual test methods described should be agreed between the parties involved.
Ungeformte feuerfeste Erzeugnisse - Teil 7: Prüfungen an Fertigteilen
Diese Europäische Norm legt Verfahren für die Prüfung von Fertigteilen im Anlieferungszustand fest. Sie gilt für Formteile aus dichten und wärmedämmenden Feuerbetonen sowie Rammassen, wie sie in prEN 1402-1 festgelegt sind.
ANMERKUNG Abnahmewerte für die beschriebenen Einzelprüfverfahren sollten zwischen den Vertragspartnern vereinbart werden.
Produits réfractaires non façonnés - Partie 7: Essais sur pièces pré-formées
La présente Norme européenne définit les méthodes d'essai des pièces pré-formées dans leur état de livraison. Elle s'applique aux produits fabriqués à partir de bétons denses et isolants et de matériaux moulables, tels que définis dans le prEN1402-1.
NOTE Il convient que les valeurs d'acceptation pour chaque méthode d'essai individuelle décrite soient fixées par accord entre les parties.
Neoblikovani ognjevzdržni izdelki - 7. del: Preskusi predhodno izdelanih oblikovancev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neoblikovani ognjevzdržni izdelki - 7. del: Preskusi predhodno izdelanih oblikovancevUngeformte feuerfeste Erzeugnisse - Teil 7: Prüfungen an FertigteilenProduits réfractaires non façonnés - Partie 7: Essais sur pieces pré-forméesUnshaped refractory products - Part 7: Tests on pre-formed shapes81.080Ognjevzdržni materialiRefractoriesICS:Ta slovenski standard je istoveten z:EN 1402-7:2003SIST EN 1402-7:2004en01-maj-2004SIST EN 1402-7:2004SLOVENSKI
STANDARDSIST ENV 1402-7:19981DGRPHãþD
SIST EN 1402-7:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1402-7October 2003ICS 81.080Supersedes ENV 1402-7:1998English versionUnshaped refractory materials - Part 7: Tests on pre-formedshapesProduits et matériaux réfractaires - Partie 7: Essais surpièces pré-forméesUngeformte feuerfeste Erzeugnisse - Teil 7: Prüfungen anFertigteilenThis European Standard was approved by CEN on 20 June 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1402-7:2003 ESIST EN 1402-7:2004
EN 1402-7:2003 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Principle.75Apparatus.76Inspection by attributes.96.1Preparation of the test piece.96.2Measurement of dimensions.96.3Measurement of angles.106.4Measurement of warpage.106.5Measurement of corner defects.116.6Measurement of edge defects.126.7Measurement of craters and bubbles.136.8Measurement of cracks.146.9Measurement of protrusions and indentations.156.10Measurement of fins.156.11Segregations.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.