Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 6: Specific functional recommendations for unplasticized polyamide (PA-U)

This document describes the specific functional requirements for polyamide (PA) pipelines in addition to the general functional requirements of EN 12007-1 for:
a) a maximum operating pressure (MOP) up to and including 16 bar;
b) an operating temperature between −20 °C and +40 °C.
This document covers one type of pipe:
- PA pipes single layer solid wall.
This document specifies common basic principles for gas infrastructure.
NOTE 1 Users of this document are aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
NOTE 2 In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
CEN/TR 13737 (all parts) give:
- clarification of all legislations/regulations applicable in a member state;
- if appropriate, more restrictive national requirements;
- a national contact point for the latest information.

Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 6: Spezifische funktionale Anforderungen für weichmacherfreies Polyamid

Dieses Dokument beschreibt, in Ergänzung zu den allgemeinen funktionalen Anforderungen von EN 12007-1, die besonderen funktionalen Anforderungen an Rohrleitungen aus Polyamid (PA) für:
a) einen maximal zulässigen Betriebsdruck (MOP) bis zu 16 bar;
b) und einer Betriebstemperatur von −20 °C und +40 °C.
Dieses Dokument umfasst einen Rohrtyp:
- einschichtige PA-Rohre mit fester Wand.
Dieses Dokument legt gemeinsame Grundprinzipien für die Gasinfrastruktur fest.
ANMERKUNG 1 Die Anwender dieses Dokuments sind sich bewusst, dass detailliertere nationale Normen und/oder Verfahrensregeln in den CEN-Mitgliedstaaten bestehen können.
Dieses Dokument soll in Verbindung mit diesen, die oben erwähnten allgemeinen Grundsätze darlegenden nationalen Normen und/oder Technischen Regeln angewendet werden.
ANMERKUNG 2 Für den Fall eines Konflikts zwischen strengeren nationalen gesetzlichen Anforderungen/Bestimmungen und den Anforderungen diesem Dokument ist den nationalen gesetzlichen Anforderungen/Bestimmungen wie in CEN/TR 13737 (alle Teile) ausgeführt Vorrang einzuräumen.
CEN/TR 13737 (alle Teile) enthält
- eine Klarstellung aller geltenden Rechtsvorschriften/Bestimmungen eines Mitgliedsstaats;
- ggf. weitergehende strengere nationale Anforderungen;
- einen nationalen Ansprechpartner für die Weitergabe neuester Informationen.

Infrastructures gazières - Canalisations pour pression maximale de service inférieure ou égale à 16 bar - Partie 6 : Recommandations fonctionnelles spécifiques pour le polyamide non plastifié (PA-U)

Le présent document décrit les exigences fonctionnelles particulières pour les canalisations en polyamide (PA) en complément des exigences fonctionnelles générales de l'EN 12007-1 pour :
a) une pression maximale de service (MOP) inférieure ou égale à 16 bar ;
b) une température d'exploitation comprise entre -20 °C et +40 °C.
Le présent document couvre un seul type de tube :
- tubes en polyamide à paroi solide monocouche.
Le présent document spécifie les principes de base communs pour les infrastructures gazières.
NOTE 1 Les utilisateurs du présent document gardent à l'esprit l'existence éventuelle, dans les pays membres du CEN, de codes de pratique et/ou de normes nationales plus détaillés.
Le présent document est destiné à être appliqué conjointement avec ces normes nationales et/ou codes de pratique, qui détaillent les principes de base précités.
NOTE 2 En cas de conflits liés à des exigences législatives/réglementaires plus restrictives que les prescriptions du présent document, la législation/réglementation nationale doit prévaloir, comme illustré dans le CEN/TR 13737 (toutes parties).
Le CEN/TR 13737 (toutes parties) fournit :
- la clarification des législations/règles pertinentes applicables dans un pays membre ;
- si approprié, les exigences nationales plus restrictives ;
- un contact national pour les dernières informations.

Infrastruktura za plin - Cevovodni sistemi za najvišji delovni tlak do vključno 16 bar - 6. del: Posebne funkcionalne zahteve za neplastificirani (nemehčani) poliamid (PA-U)

General Information

Status
Published
Publication Date
09-Mar-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
10-Mar-2021
Due Date
18-Nov-2021
Completion Date
10-Mar-2021

Buy Standard

Technical specification
TS CEN/TS 12007-6:2021 - BARVE
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
kTS FprCEN/TS 12007-6:2020 - BARVE
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 12007-6:2021
01-maj-2021
Infrastruktura za plin - Cevovodni sistemi za najvišji delovni tlak do vključno 16
bar - 6. del: Posebne funkcionalne zahteve za neplastificirani (nemehčani)
poliamid (PA-U)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar
- Part 6: Specific functional recommendations for unplasticized polyamide (PA-U)
Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis
einschließlich 16 bar - Teil 6: Spezifische funktionale Anforderungen für
weichmacherfreies Polyamid
Infrastructures gazières - Canalisations pour pression maximale de service inférieure ou
égale à 16 bar - Partie 6 : Recommandations fonctionnelles spécifiques pour le
polyamide non plastifié (PA-U)
Ta slovenski standard je istoveten z: CEN/TS 12007-6:2021
ICS:
83.140.40 Gumene cevi Hoses
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
SIST-TS CEN/TS 12007-6:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 12007-6:2021

---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 12007-6:2021


CEN/TS 12007-6
TECHNICAL SPECIFICATION

SPÉCIFICATION TECHNIQUE

March 2021
TECHNISCHE SPEZIFIKATION
ICS 23.040.20
English Version

Gas infrastructure - Pipelines for maximum operating
pressure up to and including 16 bar - Part 6: Specific
functional recommendations for unplasticized polyamide
(PA-U)
Infrastructures gazières - Canalisations pour pression Gasinfrastruktur - Rohrleitungen mit einem maximal
maximale de service inférieure ou égale à 16 bar - zulässigen Betriebsdruck bis einschließlich 16 bar -
Partie 6 : Recommandations fonctionnelles spécifiques Teil 6: Spezifische funktionale Anforderungen für
pour le polyamide non plastifié (PA-U) weichmacherfreies Polyamid
This Technical Specification (CEN/TS) was approved by CEN on 25 January 2021 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 12007-6:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 12007-6:2021
CEN/TS 12007-6:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Symbols and abbreviations . 6
5 Design . 7
5.1 General . 7
5.2 Materials and components . 7
5.3 Maximum operating pressure .
...

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 12007-6:2020
01-november-2020
Infrastruktura za plin - Cevovodni sistemi za najvišji delovni tlak do vključno 16
bar - 6. del: Posebne funkcionalne zahteve za neplastificirani poliamid (PA-U)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar
- Part 6: Specific functional recommendations for unplasticized polyamide (PA-U)
Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis
einschließlich 16 bar - Teil 6: Spezifische funktionale Anforderungen für
weichmacherfreies Polyamid
Infrastructures gazières - Canalisations pour pression maximale de service inférieure ou
égale à 16 bar - Partie 6 : Recommandations fonctionnelles spécifiques pour le
polyamide non plastifié (PA-U)
Ta slovenski standard je istoveten z: FprCEN/TS 12007-6
ICS:
83.140.40 Gumene cevi Hoses
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
kSIST-TS FprCEN/TS 12007-6:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 12007-6:2020

---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 12007-6:2020


FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 12007-6
SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION

October 2020
ICS 23.040.20
English Version

Gas infrastructure - Pipelines for maximum operating
pressure up to and including 16 bar - Part 6: Specific
functional recommendations for unplasticized polyamide
(PA-U)
Infrastructures gazières - Canalisations pour pression Gasinfrastruktur - Rohrleitungen mit einem maximal
maximale de service inférieure ou égale à 16 bar - zulässigen Betriebsdruck bis einschließlich 16 bar -
Partie 6 : Recommandations fonctionnelles spécifiques Teil 6: Spezifische funktionale Anforderungen für
pour le polyamide non plastifié (PA-U) weichmacherfreies Polyamid


This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 234.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 12007-6:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 12007-6:2020
FprCEN/TS 12007-6:2020 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Symbols and abbreviations . 7
5 Design . 8
5.1 General . 8
5.2 Materials and components . 8
5.3 Maximum operating pressure . 8
5.3.1 General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.