EN 115-1:2008
(Main)Safety of escalators and moving walks - Part 1: Construction and installation
Safety of escalators and moving walks - Part 1: Construction and installation
1.1 This standard is applicable for new escalators and moving walks (pallet or belt type) as defined in Clause 3.
This standard deals with all significant hazards, hazardous situations and events relevant to escalators and moving walks when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
1.2 This standard does not deal with hazards arising from seismic activities.
1.3 This document is not applicable to escalators and moving walks which were manufactured before the date of its publication as EN. It is, however, recommended that existing installations be adapted to this standard.
Sicherheit von Fahrtreppen und Fahrsteigen - Teil 1: Konstruktion und Einbau
1.1 Diese Norm gilt für neue Fahrtreppen und Fahrsteige (Paletten- oder Gurtkonstruktion) wie im Abschnitt 3 angegeben.
Diese Norm behandelt alle für Fahrtreppen und Fahrsteige signifikanten Gefährdungen, Gefährdungs-situationen und Gefährdungsereignisse (wie in Abschnitt 4 angegeben), wenn sie bestimmungsgemäß und unter Bedingungen, die vom Hersteller als Fehlanwendung vernünftigerweise vorhersehbar sind, verwendet werden.
1.2 Diese Norm behandelt keine Gefährdungen, die durch seismische Aktivitäten hervorgerufen werden.
1.3 Dieses Dokument gilt nicht für Fahrtreppen und Fahrsteige, die hergestellt wurden, bevor CEN dieses Dokument veröffentlichte. Es wird jedoch empfohlen, dass bestehende Anlagen an diese Norm angepasst werden.
Sécurité des escaliers mécaniques et trottoirs roulants - Partie 1: Construction et installation
1.1 La présente norme est applicable aux nouveaux escaliers mécaniques et trottoirs roulants (à palettes ou à bande) tels que définis à l’Article 3.
Cette norme prend en compte tous les risques significatifs, les situations et événements dangereux relatifs aux escaliers mécaniques et trottoirs roulants, utilisés conformément à l’usage pour lequel ils ont été prévus ainsi que dans des cas d’utilisations inappropriées qui peuvent être raisonnablement prévisibles par le constructeur (voir Article 4).
1.2 Cette norme ne prend pas en compte les risques émanant de l’activité sismique.
1.3 Le présent document ne s’applique pas aux escaliers mécaniques et trottoirs roulants fabriqués avant la date de publication de ce document en tant que norme EN. Il est toutefois recommandé que les installations existantes soient adaptées à cette norme.
NOTE Pour ce type particulier de machines le bruit n’est pas considéré comme un risque significatif ou pertinent.
Varnost tekočih stopnic in trakov za osebe (stez) - 1. del: Konstrukcija in vgradnja
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Fahrtreppen und Fahrsteigen - Teil 1: Konstruktion und EinbauSafety of escalators and moving walks - Part 1: Construction and installation91.140.90Lifts. EscalatorsICS:Ta slovenski standard je istoveten z:EN 115-1:2008SIST EN 115-1:2009en,fr,de01-april-2009SIST EN 115-1:2009SLOVENSKI
STANDARDSIST EN 115:1997/A2:2004SIST EN 115:1997/A1:19991DGRPHãþD
SIST EN 115-1:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 115-1July 2008ICS 91.140.90Supersedes EN 115:1995
English VersionSafety of escalators and moving walks - Part 1: Constructionand installationSécurité des escaliers mécaniques et trottoirs roulants -Partie 1: Construction et installationSicherheit von Fahrtreppen und Fahrsteigen - Teil 1:Konstruktion und EinbauThis European Standard was approved by CEN on 29 May 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 115-1:2008: ESIST EN 115-1:2009
EN 115-1:2008 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms and definitions - Symbols and abbreviations.8 3.1 Terms and definitions.8 3.2 Symbols and abbreviations.10 4 List of significant hazards.12 4.1 General.12 4.2 Mechanical hazards.13 4.3 Electric hazards.13 4.4 Radiation hazards.13 4.5 Fire hazard.14 4.6 Hazards generated by neglecting ergonomic principles in machinery design.14 4.7 Hazard generated by failure of control circuit.14 4.8 Hazards generated by break-up during operation.14 4.9 Slipping, tripping and falling hazards.14 4.10 Hazards specific for this type of machine.15 5 Safety requirements and/or protective measures.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.