EN ISO 11640:2018
(Main)Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing (ISO 11640:2018)
Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing (ISO 11640:2018)
This document specifies a method for determining the behaviour of the surface of a leather on rubbing with a wool felt.
It is applicable to leathers of all kinds.
Leder - Farbechtheitsprüfungen - Bestimmung der Reibechtheit von Färbungen (ISO 11640:2018)
Cuir - Essais de solidité des coloris - Solidité des coloris au frottement en va-et-vient (ISO 11640:2018)
Le présent document spécifie une méthode permettant de déterminer le comportement de la surface d'un cuir soumise à un frottement avec du feutre de laine.
Il s'applique à toutes les sortes de cuir.
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti drgnjenju v dveh nasprotnih smereh (ISO 11640:2018)
Ta dokument določa metodo za ugotavljanje vedenja površine usnja pri drgnjenju
z volneno klobučevino. Uporablja se za vse vrste usnja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2018
1DGRPHãþD
SIST EN ISO 11640:2013
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti drgnjenju v dveh
nasprotnih smereh (ISO 11640:2018)
Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing (ISO
11640:2018)
Leder - Farbechtheitsprüfungen - Bestimmung der Reibechtheit von Färbungen (ISO
11640:2018)
Cuir - Essais de solidité des coloris - Solidité des coloris au frottement en va-et-vient
(ISO 11640:2018)
Ta slovenski standard je istoveten z: EN ISO 11640:2018
ICS:
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11640
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 59.140.30 Supersedes EN ISO 11640:2012
English Version
Leather - Tests for colour fastness - Colour fastness to
cycles of to-and-fro rubbing (ISO 11640:2018)
Cuir - Essais de solidité des coloris - Solidité des coloris Leder - Farbechtheitsprüfungen - Bestimmung der
au frottement en va-et-vient (ISO 11640:2018) Reibechtheit von Färbungen (ISO 11640:2018)
This European Standard was approved by CEN on 15 July 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11640:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11640:2018) has been prepared by Technical Committee ISO/IULTCS
"International Union of Leather Technologists and Chemists Societies" in collaboration with Technical
Committee CEN/TC 289 “Leather” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11640:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11640:2018 has been approved by CEN as EN ISO 11640:2018 without any modification.
INTERNATIONAL ISO
STANDARD 11640
IULTCS/IUF 450
Third edition
2018-07
Leather — Tests for colour fastness
— Colour fastness to cycles of to-and-
fro rubbing
Cuir — Essais de solidité des coloris — Solidité des coloris au
frottement en va-et-vient
Reference numbers
ISO 11640:2018(E)
IULTCS/IUF 450:2018(E)
©
ISO 2018
ISO 11640:2018(E)
IULTCS/IUF 450:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 11640:2018(E)
IULTCS/IUF 450:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials. 2
6 Test specimens. 3
7 Conditioning of test specimens and pieces of felt . 3
7.1 Dry leather and dry felt . 3
7.2 Wet felt . 3
7.3 Wet leather . 3
7.4 Felt wetted with artificial perspiration solution . 4
8 Procedure. 4
9 Precision . 5
10 Test report . 5
Annex A (informative) Commercial sources for apparatus and materials.6
ISO 11640:2018(E)
IULTCS/IUF 450:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html
This document was prepared by the Fastness Tests Commission of the International Union of Leather
Technologists and Chemists Societies (IUF Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, the secretariat of
which is held by UNI, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
The first edition was based on IUF 450 published in J. Soc. Leather Tech. Chem., 71, pp. 24–25 (1987), and
declared an official method of the IULTCS in October 1989.
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to
further the advancement of leather science and technology. IULTCS has three Commissions, which
are responsible for establishing international methods for the sampling and testing of leather. ISO
recognizes IULTCS as an international standardizing body for the preparation of test methods for
leather.
This third edition cancels and replaces the second edition (ISO 11640:2012). This new version is a
technical update of the procedures. Clause 3 is new, and 5.2, 7.2, 7.4, 8.2, 8.6 and 8.7 have been revised.
The rubbing of a leather surface with a wool felt is also known as the “VESLIC rub test”. VESLIC
(Association of Swiss Leather Chemists and Technologists) was the original developer of the test
method and equipment.
iv © ISO 2018 – All rights reserved
ISO 11640:2018(E)
INTERNATIONAL STANDARD
IULTCS/IUF 450:2018(E)
Leather — Tests for colour fastness — Colour fastness to
cycles of to-and-fro rubbing
1 Scope
This document specifies a method for determining the behaviour of the surface of a leather on rubbing
with a wool felt.
It is applicable to leathers of all kinds.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 105-A01, Textiles — Tests for colour fastness — Part A01: General principles of testing
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 105-A03, Textiles — Tests for colour fastness — Part A03: Grey scale for assessing staining
ISO 105-A04, Textiles — Tests for colour fastness — Part A04: Method for the instrumental assessment of
the degree of staining of adjacent fabrics
ISO 105-A05, Textiles — Tests for colour fastness — Part A05: Instrumental assessment of change in colour
for determination of grey scale rating
ISO 2418, Leather — Chemical, physical and mechanical and fastness tests — Sampling location
ISO 2419, Leather — Physical and mechanical tests — Sample preparation and conditioning
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 4045, Leather — Chemical tests — Determination of pH and difference figure
ISO 9073-2, Textiles — Test methods for nonwovens — Part 2: Determination of thickness
ISO 11641, Leather — Tests for colour fastness — Colour fastness to perspiration
EN 15987, Leather — Terminology — Key definitions for the leather trade
3 Terms and definitions
For the purposes of this document, the leather terms and definitions given in EN 159
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.