prEN ISO 17635
(Main)Non-destructive testing of welds - General rules for metallic materials (ISO/DIS 17635:2023)
Non-destructive testing of welds - General rules for metallic materials (ISO/DIS 17635:2023)
ISO 17635:2016 gives guidelines for the choice of non-destructive testing (NDT) methods for welds and evaluation of the results for quality control purposes, based on quality requirements, material, weld thickness, welding process and extent of testing.
ISO 17635:2016 also specifies general rules and standards to be applied to the different types of testing, for either the methodology or the acceptance levels for metallic materials.
Acceptance levels cannot be a direct interpretation of the quality levels defined in ISO 5817 or ISO 10042. They are linked to the overall quality of the produced batch of welds.
Requirements for acceptance levels for NDT comply with quality levels stated in ISO 5817 or ISO 10042 (moderate, intermediate, stringent) only on a general basis and not in detail for each indication.
Annex A gives correlations between quality, NDT and acceptance level standards.
Annex B gives an overview of the standards linked to quality levels, acceptance levels and NDT methods.
Zerstörungsfreie Prüfung von Schweißverbindungen - Allgemeine Regeln für metallische Werkstoffe (ISO/DIS 17635:2023)
Essais non destructifs des assemblages soudés - Règles générales pour les matériaux métalliques (ISO/DIS 17635:2023)
ISO 17635:2016 donne des lignes directrices pour le choix des méthodes d'essai non destructif (END) des assemblages soudés et l'évaluation des résultats dans le cadre du contrôle qualité, en se fondant sur les exigences concernant la qualité, le matériau, l'épaisseur de soudure, le procédé de soudage et l'étendue de l'essai.
ISO 17635:2016 spécifie également les règles générales et les normes applicables aux différents types d'essai, tant du point de vue de la méthodologie que des niveaux d'acceptation pour les matériaux métalliques.
Les niveaux d'acceptation ne peuvent pas être une interprétation directe des niveaux de qualité définis dans l'ISO 5817 ou l'ISO 10042. Ils sont liés à la qualité globale du lot d'assemblages soudés produit.
Les exigences relatives aux niveaux d'acceptation pour les END ne sont corrélées aux niveaux de qualité définis dans l'ISO 5817 ou l'ISO 10042 (modérés, moyens et élevés) que sur une base générale, et non pas en détail pour chaque indication.
L'Annexe A établit une corrélation entre les normes relatives à la qualité, aux essais non destructifs et aux niveaux d'acceptation.
L'Annexe B donne une vue d'ensemble des normes relatives aux niveaux de qualité, aux niveaux d'acceptation et aux méthodes d'essai non destructif.
Neporušitveno preskušanje zvarnih spojev - Splošna pravila za kovinske materiale (ISO/DIS 17635:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2024
Neporušitveno preskušanje zvarnih spojev - Splošna pravila za kovinske materiale
(ISO/DIS 17635:2023)
Non-destructive testing of welds - General rules for metallic materials (ISO/DIS
17635:2023)
Zerstörungsfreie Prüfung von Schweißverbindungen - Allgemeine Regeln für metallische
Werkstoffe (ISO/DIS 17635:2023)
Essais non destructifs des assemblages soudés - Règles générales pour les matériaux
métalliques (ISO/DIS 17635:2023)
Ta slovenski standard je istoveten z: prEN ISO 17635
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17635
ISO/TC 44/SC 5 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2023-11-29 2024-02-21
Non-destructive testing of welds — General rules for
metallic materials
Contrôle non destructif des assemblages soudés — Règles générales pour les matériaux métalliques
ICS: 25.160.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 17635:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 17635:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17635
ISO/TC 44/SC 5 Secretariat: AFNOR
Voting begins on: Voting terminates on:
Non-destructive testing of welds — General rules for
metallic materials
Contrôle non destructif des assemblages soudés — Règles générales pour les matériaux métalliques
ICS: 25.160.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 17635:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 17635:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Abbreviated terms . 3
5 Limitations . 3
5.1 Stage of manufacture . 3
5.2 Extent of testing . 4
5.3 Materials . 4
6 Personnel qualification .4
7 Testing organization . 4
8 Documentation . 4
8.1 Documentation prior to testing . 4
8.1.1 General . 4
8.1.2 Written procedures . 4
8.1.3 Testing plan . 4
8.2 Documentation after testing . 5
8.2.1 Records of individual testing . 5
8.2.2 Final test report . 5
9 Selection of testing method . 5
9.1 General . 5
9.2 Butt- and T-joints with full penetration . 6
9.3 Butt- and T-joints without full penetration and fillet welds . 6
10 Performance of testing . 7
10.1 Determination of standards to be applied . 7
10.2 Conditions for testing . 7
10.3 Time of testing . 7
10.4 Non-acceptable indications . 7
10.5 Repaired welds . 7
Annex A (normative) Rules and standards to be applied . 8
Annex B (informative) Graphs of standard context .12
Bibliography .14
iii
ISO/DIS 17635:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 5, Testing and inspection of welds.
This fourth edition cancels and replaces the third edition (ISO 17635:2016), which has been technically
revised.
The main changes are as follows:
— references updated;
— Phased-array ultrasonic technique (UT-PA) for thin-walled steel components added;
— Total focusing technique (TFM) added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT INTERNATIONAL STANDARD ISO/DIS 17635:2023(E)
Non-destructive testing of welds — General rules for
metallic materials
1 Scope
This document gives guidelines for the choice of non-destructive testing (NDT) methods for welds in
metals and for the evaluation of the results for quality control purposes, based on quality requirements,
material, weld thickness, welding process and extent of testing.
This document also specifies general rules and standards to be applied to the different types of testing,
for the selection of the method, the techniques and the acceptance levels.
Acceptance levels cannot be a direct interpretation of the quality levels defined in ISO 5817 or
ISO 10042. They are linked to the overall quality of the produced batch of welds.
Requirements for acceptance levels for NDT comply with quality levels stated in ISO 5817 or ISO 10042
(moderate, intermediate, stringent) only on a general basis and not in detail for each indication.
Annex A gives correlations between quality levels, testing levels and acceptance levels for specific
testing techniques.
Annex B gives an overview of the standards linked to quality levels, acceptance levels and testing
methods for specific testing techniques.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3452-1, Non-destructive testing — Penetrant testing — Part 1: General principles
ISO 4761, Non-destructive testing of welds — Phased array ultrasonic testing (UT-PA) for thin-walled steel
components — Acceptance levels
ISO 5817, Weldin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.