iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13016-1:2000

(Main)

Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP)

Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP)

This European Standard specifies a method for the determination of the total pressure, exerted in vacuo, by volatile, low viscosity petroleum products, components, and feedstocks containing air. An equivalent dry vapour pressure can be calculated from the air containing vapour pressure (ASVP) measurement. The conditions used in the test described in this standard are a vapour-to-liquid ratio of 4:1, a sample size of 1 l, and a test temperature of 37,8°C. Note 1 See annex A for information on the precision values when using 50 ml samples or using a test temperature of 50,0°C.

Flüssige Mineralölerzeugnisse - Dampfdruck - Teil 1: Bestimmung des luftgesättigten Dampfdruckes (ASVP)

Diese Europäische Norm beschreibt ein Verfahren zur Messung des absoluten Dampfdrucks, gemessen im Vakuum, ausgeübt von luftgesättigten, niedrigviskosen Mineralölerzeugnissen, Komponenten und Feedstocks. Ein Äquivalent zum "Trockenen Dampfdruck" (DVPE, siehe Abschnitt 12) kann aus diesem "Luftgesättigten Dampfdruck" (ASVP) berechnet werden. Die in dieser Norm bei der Prüfung vorgeschriebenen Prüfbedingungen sind ein Dampf-Flüssigkeitsverhältnis von 4:1, ein Probenvolumen von 1 l und eine Prüftemperatur von 37,8°C.

Produits pétroliers liquides - Pression de vapeur - Partie 1: Détermination de la pression de vapeur saturée en air (PVSA)

La présente Norme européenne prescrit une méthode de détermination de la pression totale exercée dans le vide par des produits pétroliers, des bases pétrolières et des constituants pétroliers, volatils, de faible viscosité et contenant de l'air. Il est possible de calculer une pression de vapeur sèche équivalente à partir de la mesure de la pression de vapeur saturée en air (PVSA). Les conditions mises en oeuvre dans l'essai décrit dans la présente Norme sont un rapport vapeur sur liquide de 4:1, un volume d'échantillon de 1 l et une température d'essai de 37,8°C.

Tekoči naftni proizvodi - Parni tlak - 1. del: Določevanje z zrakom nasičenega parnega tlaka (ASVP)

General Information

Status
Withdrawn
Publication Date
22-Aug-2000
Withdrawal Date
11-Sep-2007
ICS
75.160.20 - Liquid fuels
Technical Committee
CEN/TC 19 - Petroleum products, lubricants and related products
Drafting Committee
CEN/TC 19/WG 15 - Vapour pressure methods
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
12-Sep-2007
Completion Date
12-Sep-2007
Ref Project
SIST EN 13016-1:2000 - Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP)

Relations

Replaced By
EN 13016-1:2007 - Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE)
Effective Date
22-Dec-2008
Child
EN 58:2004 - Bitumen and bituminous binders - Sampling bituminous binders
Effective Date
22-Dec-2008

Buy Standard

EN 13016-1:2000EN 13016-1:2000
PreviousNext
Standard
EN 13016-1:2000
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13016-1:2000
01-december-2000
7HNRþLQDIWQLSURL]YRGL3DUQLWODNGHO'RORþHYDQMH]]UDNRPQDVLþHQHJD
SDUQHJDWODND $693
Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated
vapour pressure (ASVP)
Flüssige Mineralölerzeugnisse - Dampfdruck - Teil 1: Bestimmung des luftgesättigten
Dampfdruckes (ASVP)
Produits pétrolier
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17867:2023(Main)
Petrol fuel for small internal combustion engines - Requirements and test methods
SIST EN 17867:2023

This document specifies requirements on petrol fuel for use as fuel in small engines, together with the methods to be applied for testing these properties.
This document specifies requirements for two types of petrol fuel having low aromatics and sulfur content:
- one type for use in four-stroke engines with separate lubrication; and
- one mixed petrol fuel type for use in mixture-lubricated engines.
Testing the properties of the added engine oil is out of the scope of this document.
NOTE For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15691:2023(Main)
Ethanol as a blending component for petrol - Determination of dry residue (involatile material) - Gravimetric method
SIST EN 15691:2023

This document specifies a procedure for the determination of dry residue in ethanol by gravimetric (desiccation) method in the range (10 to 25) mg/100 ml.
NOTE In an interlaboratory study [2] the method described has been tested at levels down to 3,5 mg/100 ml, but the precision appeared to be insufficient at such low levels.
WARNING - Use of this document can involve hazardous equipment, materials and operations. This method does not purport to address to all of the safety problems associated with its use. It is the responsibility of the user of this document to take appropriate measures to ensure the safety and health of personnel prior to the application of the document, and to fulfil statutory and regulatory restrictions for this purpose.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15940:2023(Main)
Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods
SIST EN 15940:2023

This document describes requirements and test methods for paraffinic diesel fuel marketed and delivered as such, containing a level of up to 7,0 % (V/V) fatty acid methyl ester (FAME). It is applicable to fuel for use in diesel engines and vehicles compatible with paraffinic diesel fuel. It specifies two classes of paraffinic diesel fuel: high cetane and normal cetane.
Paraffinic diesel fuel originates from synthesis or hydrotreatment processes.
NOTE 1   For general diesel engine warranty, the vehicle manufacturer needs to be consulted before use. Paraffinic automotive diesel fuel may need a validation step to confirm the compatibility of the fuel with the vehicle, which for some existing engines may still need to be done (see also the Introduction to this document). However, it is noted that paraffinic diesel fuel is extensively available and has been increasingly approved by vehicle manufacturers for usage in vehicles since the first publication of this document.
NOTE 2   For the purposes of this document, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction and the volume fraction.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16568:2023(Main)
Automotive fuels - Blends of Fatty acid methyl ester (FAME) with diesel fuel - Determination of oxidation stability by rapidly accelerated oxidation method at 120 °C
SIST EN 16568:2023

This document specifies a test method for the determination of the oxidation stability at 120 °C of fuels for diesel engines, by means of measuring the induction period of the fuel up to 20 h. The method is applicable to blends of FAME with petroleum-based diesel having a FAME content in the range between 2 % (V/V) and 50 % (V/V).
NOTE 1   An almost identical test method for oxidation stability at 110 °C is described in EN 15751 [1], which applies to pure FAME and diesel/FAME blends containing 2 % (V/V) of FAME at minimum. Other alternative test methods for the determination of the oxidation stability of distillate fuels are described in CEN/TR 17225 [3].
NOTE 2   The precision of this method was determined using samples with a maximum induction period of approximately 20 h. Higher induction periods are not covered by the precision statement; however, experience from EN 15751 indicates sufficient precision up to 48 h.
NOTE 3   The presence of cetane improver can reduce the oxidation stability determined by this test method. Limited studies with 2-ethyl hexyl nitrate (EHN) indicated that the stability is reduced to an extent which is within the reproducibility of the test method.
NOTE 4   For the purposes of this document, the term "% (V/V)" is used to represent the volume fraction.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15195:2023(Main)
Liquid petroleum products - Determination of ignition delay and derived cetane number (DCN) of middle distillate fuels by combustion in a constant volume chamber
SIST EN 15195:2023

This document specifies a test method for the quantitative determination of ignition delay of middle distillate fuels intended for use in compression ignition engines. The method utilizes a constant volume combustion chamber designed for operation by compression ignition, and employing direct injection of fuel into compressed air that is controlled to a specified pressure and temperature. An equation is given to calculate the derived cetane number (DCN) from the ignition delay measurement.
This document covers the ignition delay range from 2,58 ms to 6,34 ms (76,8 DCN to 33,9 DCN). The combustion analyser can measure shorter or longer ignition delays, but precision is not known.
This document is applicable to diesel fuels, including those containing fatty acid methyl esters (FAME) up to 30 % (V/V). The method is also applicable to middle distillate fuels of non-petroleum origin, oil-sands based fuels, blends of fuel containing biodiesel material, diesel fuel oils containing cetane number improver additives and low-sulfur diesel fuel oils. Furthermore, the method is applicable to paraffinic diesel from synthesis or hydrotreatment, containing up to a volume fraction of 7 % FAME [1]. However, users applying this document especially to unconventional distillate fuels are warned that the relationship between derived cetane number and combustion behaviour in real engines is not yet fully understood.
The test method is also applicable to the quantitative determination of the ignition characteristics of FAME, especially the ignition delay. However, analysis of the data available, regarding correlation with EN ISO 5165, is inconclusive. So the determination of derived cetane number for FAME fuel, also known as B100, has not been included in the precision determination as in Clause 12.
NOTE    For the purpose of this document, the expression “% (V/V)” is used to represent the volume fraction and “% (m/m)” the mass fraction.
WARNING — The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16329:2022(Main)
Diesel and domestic heating fuels - Determination of cold filter plugging point - Linear cooling bath method
SIST EN 16329:2023

This document specifies an automated method for the determination of the cold filter plugging point (CFPP) of diesel and domestic heating fuels using linear cooling.
This document is applicable to fatty-acid methyl esters (FAME) and to distillate fuels as well as paraffinic diesel fuels, including those containing FAME, flow-improvers or other additives, intended for use in diesel engines and domestic heating installations.
The results obtained from the method specified in this document are suitable for estimating the lowest temperature at which a fuel will give trouble-free flow in the fuel system.
NOTE   In the case of diesel fuels, the results are usually close to the temperature of failure in service except when the fuel system contains, for example, a paper filter installed in a location exposed to the weather or if the filter plugging temperature is more than 12 °C below the cloud point of the fuel. Domestic heating installations are usually less critical and often operate at a satisfactory level at temperatures somewhat lower than those indicated by the test results.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12177:2022(Main)
Liquid petroleum products - Unleaded petrol - Determination of benzene content by gas chromatography
SIST EN 12177:2023

This document specifies a column switching gas chromatographic method for the quantitative determination of benzene content in the range 0,05 % (V/V) to 6 % (V/V) in unleaded petrol having a final boiling point not greater than 220 °C.
The method described in this document is suitable for determining benzene in petrol, including petrol containing oxygenates up to E10 (up to 3,7 % (m/m) oxygen content), in line with the relevant EC Directives [1].
NOTE   For the purposes of this document, the terms "% (V/V)" and "% (m/m)" are used to represent respectively the volume fraction and the mass fraction.
WARNING - Use of this document might involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16091:2022(Main)
Liquid petroleum products - Middle distillates and fatty acid methyl ester (FAME) fuels and blends - Determination of oxidation stability by rapid small scale oxidation test (RSSOT)
SIST EN 16091:2022

This document specifies a method for the determination of the oxidation stability of middle distillate fuels, fatty acid methyl ester (FAME) fuel and blends thereof, under accelerated conditions, by measuring the induction period to the specified breakpoint in a reaction vessel charged with the sample and oxygen at 140 °C.
NOTE 1 For the purposes of this document, the term "% (V/V)" is used to represent the volume fraction (φ).
NOTE 2 The induction period is used as an indication for the resistance of middle distillates, fatty acid methyl ester (FAME) fuels and blends thereof against oxidation. This correlation can vary markedly under different conditions with different FAMEs and diesel fuel blends.
NOTE 3 The presence of ignition improvers can lead to lower oxidation stability results determined by this method. It has for instance been observed that the addition of 2-ethyl hexyl nitrate (2-EHN) can reduce the measured oxidation stability values. See [6] for details.
NOTE 4 For further information on the precision data at a test temperature of 120 °C see Annex C.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16734:2022(Main)
Automotive fuels - Automotive B10 diesel fuel - Requirements and test methods
SIST EN 16734:2022

This document specifies requirements and test methods for marketed and delivered automotive B10 diesel fuel, i.e. diesel fuel containing up to 10,0 %(V/V) Fatty Acid Methyl Ester. It is applicable to fuel for use in diesel engine vehicles compatible with automotive B10 diesel fuel.
NOTE 1 This product is allowed in Europe [4], but national legislation can set additional requirements or rules concerning, or even prohibiting, marketing or delivering of the product.
NOTE 2 In this document, A-deviations apply (see Annex A).
NOTE 3 For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15553:2021(Main)
Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method
SIST EN 15553:2022

This document specifies a fluorescent indicator adsorption method for the determination of hydrocarbon types over the concentration ranges from 5 % (V/V) to 99 % (V/V) aromatic hydrocarbons, 0,3 % (V/V) to 55 % (V/V) olefins, and 1 % (V/V) to 95 % (V/V) saturated hydrocarbons in petroleum fractions that distil below 315 °C. This method can apply to concentrations outside these ranges, but the precision has not been determined.
When samples containing oxygenated blending components are analysed, the hydrocarbon type results can be reported on an oxygenate-free basis or, when the oxygenate content is known, the results can be corrected to a total-sample basis.
This test method is applicable to full boiling range products. Cooperative data have established that the precision statement does not apply to petroleum fractions with narrow boiling ranges near the 315 °C limit. Such samples are not eluted properly, and results are erratic.
It does not apply to samples containing dark-coloured components that interfere with reading the chromatographic bands that cannot be analysed.
NOTE 1   The oxygenated blending components methanol, ethanol, tert-butyl methyl ether (MTBE), methyl tert-pentyl ether (TAME) and tert-butyl ethyl ether (ETBE) do not interfere with the determination of hydrocarbon types at concentrations normally found in commercial petroleum blends. These oxygenated compounds are not detected since they elute with the alcohol desorbent. The effects of other oxygenated compounds are individually verified.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day