EN ISO 1874-2:2006/A1:2010
(Amendment)Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1: Laser sintering of specimens (ISO 1874-2:2006/Amd 1:2010)
Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1: Laser sintering of specimens (ISO 1874-2:2006/Amd 1:2010)
This part of ISO 1874 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyamide moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods that are suitable and necessary to characterize polyamide moulding and extrusion materials are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 1874, as are the designatory properties (viscosity number and tensile modulus of elasticity) found in ISO 1874-1.
Kunststoffe - Polyamid (PA)-Formmassen für das Spritzgießen und die Extrusion - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften - Änderung 1: Lasersintern von Probekörpern (ISO 1874-2:2006/Amd 1:2010)
Plastiques - Matériaux polyamides (PA) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés - Amendement 1: Frittage laser des éprouvettes (ISO 1874-2:2006/Amd 1:2010)
Polimerni materiali - Poliamidni materiali (PA) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti - Dopolnilo 1: Lasersko sintranje preskušancev (ISO 1874-2:2006/Amd 1:2010)
Ta del standarda ISO 1874 določa metode za pripravo preskušancev in preskusnih metod za uporabo pri ugotavljanju lastnosti poliamidnih materialov za oblikovanje in ekstrudiranje. Podane so zahteve za ravnanje s preskusnimi materiali in obdelavo preskusnega materiala pred oblikovanjem ter preskušancev pred preskusom. Podani so postopki in pogoji za pripravo preskušancev ter postopki za merjenje lastnosti materialov, iz katerih so preskušanci izdelani. Navedene so lastnosti in preskusne metode, ki so primerne in nujne za opredelitev poliamidnih materialov za oblikovanje in ekstrudiranje. Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki se splošno uporabljajo ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta del standarda ISO 1874. Vključene so tudi označevalne lastnosti, ki so navedene v standardu ISO 1874-1 (viskoznostno število in natezni modul elastičnosti).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2014
Polimerni materiali - Poliamidni materiali (PA) za oblikovanje in ekstrudiranje - 2.
del: Priprava preskušancev in ugotavljanje lastnosti - Dopolnilo 1: Lasersko
sintranje preskušancev (ISO 1874-2:2006/Amd 1:2010)
Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test
specimens and determination of properties - Amendment 1: Laser sintering of specimens
(ISO 1874-2:2006/Amd 1:2010)
Kunststoffe - Polyamid (PA)-Formmassen für das Spritzgießen und die Extrusion - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften - Änderung 1:
Lasersintern von Probekörpern (ISO 1874-2:2006/Amd 1:2010)
Plastiques - Matériaux polyamides (PA) pour moulage et extrusion - Partie 2: Préparation
des éprouvettes et détermination des propriétés - Amendement 1: Frittage laser des
éprouvettes (ISO 1874-2:2006/Amd 1:2010)
Ta slovenski standard je istoveten z: EN ISO 1874-2:2006/A1:2010
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 1874-2:2006/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 83.080.20
English Version
Plastics - Polyamide (PA) moulding and extrusion materials -
Part 2: Preparation of test specimens and determination of
properties - Amendment 1: Laser sintering of specimens (ISO
1874-2:2006/Amd 1:2010)
Plastiques - Matériaux polyamides (PA) pour moulage et Kunststoffe - Polyamid (PA)-Formmassen für das
extrusion - Partie 2: Préparation des éprouvettes et
Spritzgießen und die Extrusion - Teil 2: Herstellung von
détermination des propriétés - Amendement 1: Frittage Probekörpern und Bestimmung von Eigenschaften -
laser des éprouvettes (ISO 1874-2:2006/Amd 1:2010) Änderung 1: Lasersintern von Probekörpern (ISO 1874-
2:2006/Amd 1:2010)
This amendment A1 modifies the European Standard EN ISO 1874-2:2006; it was approved by CEN on 13 November 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1874-2:2006/A1:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 1874-2:2006/A1:2010) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This Amendment to the European Standard EN ISO 1874:2006 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by May 2011, and
conflicting national standards shall be withdrawn at the latest by May 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1874-2:2006/Amd 1:2010 has been approved by CEN as a EN ISO 1874-2:2006/A1:2010
without any modification.
INTERNATIONAL ISO
STANDARD 1874-2
Third edition
2006-12-01
AMENDMENT 1
2010-11-15
Plastics — Polyamide (PA) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
AMENDMENT 1: Laser sintering of
specimens
Plastiques — Matériaux polyamides (PA) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
AMENDEMENT 1: Frittage laser des éprouvettes
Reference number
ISO 1874-2:2006/Amd.1:2010(E)
©
ISO 2010
ISO 1874-2:2006/Amd.1:2010(E)
PD
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.