EN ISO 10140-5:2010
(Main)Acoustics - Laboratory measurement of sound insulation of building elements - Part 5: Requirements for test facilities and equipment (ISO 10140-5:2010)
Acoustics - Laboratory measurement of sound insulation of building elements - Part 5: Requirements for test facilities and equipment (ISO 10140-5:2010)
ISO 10140-5:2010 specifies laboratory test facilities and equipment for sound insulation measurements of building elements, such as components and materials, building elements, technical elements (small building elements) and sound insulation improvement systems.
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 5: Anforderungen an Prüfstände und Prüfeinrichtungen (ISO 10140-5:2010)
Dieser Teil der ISO 10140 legt Prüfstände und Prüfeinrichtungen für die Messung der Schalldämmung von
Bauteilen fest, zum Beispiel von:
⎯ Bauteilen und Baustoffen;
⎯ Bauteilen;
⎯ technischen Bauteilen (kleine Bauteile);
⎯ Systemen zur Verbesserung der Schalldämmung.
Er gilt für Prüfstände mit unterdrückter Schallabstrahlung von flankierenden Bauteilen und baulicher Trennung
zwischen Sende- und Empfangsraum.
Dieser Teil von ISO 10140 legt die Eignungsprüfungen fest, die anzuwenden sind, wenn ein neuer Prüfstand
mit Prüfeinrichtungen für Schalldämmungsmessungen in Betrieb genommen wird. Es ist vogesehen, dass
diese Verfahren in regelmäßigen Abständen wiederholt werden, um sicherzustellen, dass mit den
Prüfeinrichtungen und dem Prüfstand keine Probleme auftreten.
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de construction - Partie 5: Exigences relatives aux installations et appareillage d'essai (ISO 10140-5:2010)
L'ISO 10140-5:2010 spécifie les installations et l'appareillage d'essai en laboratoire pour les mesurages de l'isolation acoustique des éléments de construction, tels que les composants et matériaux, les éléments de construction, les éléments techniques (petits éléments de construction) et les systèmes d'amélioration de l'isolation acoustique.
Akustika - Laboratorijsko merjenje zvočne izolirnosti gradbenih elementov - 5. del: Zahteve in oprema za laboratorije (ISO 10140-5:2010)
Ta del ISO 10140 določa laboratorije in opremo za merjenja zvočne izolirnosti gradbenih elementov, kot so: - komponente in materiali; - gradbeni elementi; - tehnični elementi (majhni gradbeni elementi); - sistemi za izboljšavo zvočne izolirnosti. Velja za laboratorije z zadušenim sevanjem iz bočnih elementov in strukturno izoliranost med virov in sobami za sprejem. Ta del ISO 10140 določa kvalifikacijske postopke, ki se uporabljajo pri začetku obratovanja novega laboratorija z opremo za merjenje zvočne izolirnosti. Njegov namen je, da se ti postopki redno ponavljajo, da se zagotovi odprava kakršnih koli težav z opremo ali z laboratorijem.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Akustik - Messung der Schalldämmung von Gebäudeteilen im Prüfstand - Teil 5: Anforderungen an Prüfstände und Prüfeinrichtungen (ISO 10140-5:2010)Acoustique - Détermination de l'isolation acoustique des éléments de construction - Partie 5: Exigences pour installations et équipements d'essai (ISO 10140-5:2010)Acoustics - Laboratory measurement of sound insulation of building elements - Part 5: Requirements for test facilities and equipment (ISO 10140-5:2010)91.120.20L]RODFLMDAcoustics in building. Sound insulationICS:Ta slovenski standard je istoveten z:EN ISO 10140-5:2010SIST EN ISO 10140-5:2010en01-december-2010SIST EN ISO 10140-5:2010SLOVENSKI
STANDARDSIST EN ISO 140-3:1997/A1:2005SIST EN ISO 140-3:1997SIST EN ISO 140-8:1998SIST EN ISO 140-6:1999SIST EN ISO 140-16:2006SIST EN ISO 140-1:1998SIST EN 20140-10:1997SIST EN ISO 140-11:2005SIST EN ISO 140-1:1998/A1:20051DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 10140-5
September 2010 ICS 91.120.20 Supersedes EN 20140-10:1992, EN ISO 140-1:1997, EN ISO 140-11:2005, EN ISO 140-16:2006, EN ISO 140-3:1995, EN ISO 140-6:1998, EN ISO 140-8:1997English Version
Acoustics - Laboratory measurement of sound insulation of building elements - Part 5: Requirements for test facilities and equipment (ISO 10140-5:2010)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de construction - Partie 5: Exigences relatives aux installations et appareillage d'essai (ISO 10140-5:2010)
Akustik -Messung der Schalldämmung von Gebäudeteilen im Prüfstand - Teil 5: Anforderungen an Prüfstände und Prüfeinrichtungen (ISO 10140-5:2010) This European Standard was approved by CEN on 14 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10140-5:2010: ESIST EN ISO 10140-5:2010
Reference numberISO 10140-5:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO10140-5First edition2010-09-01Acoustics — Laboratory measurement of sound insulation of building elements — Part 5: Requirements for test facilities and equipment Acoustique — Mesurage en laboratoire de l'isolation acoustique des éléments de construction — Partie 5: Exigences relatives aux installations et appareillages d'essai
ISO 10140-5:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 10140-5:2010(E) © ISO 2010 – All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Laboratory test facilities for airborne sound insulation measurements.2 4 Laboratory test facilities for impact sound insulation measurements.8 5 Equipment.9 Annex A (normative)
Estimation of the maximum measurable sound reduction index.10 Annex B (normative)
Standard basic elements for measuring the improvement of airborne sound insulation by linings.13 Annex C (normative)
Standard floors for measuring the improvement of impact sound insulation by floor coverings.17 Annex D (normative)
Qualification procedure for loudspeakers and loudspeaker positions.23 Annex E (normative)
Standard tapping machine.27 Annex F (normative)
Alternative impact sound sources.29 Annex G (normative)
Wooden mock-up floor for measuring the improvement of impact sound insulation by floor coverings.34 Bibliography.35
ISO 10140-5:2010(E) iv © ISO 2010 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10140-5 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building acoustics. This first edition of ISO 10140-5, together with ISO 10140-1, ISO 10140-2, ISO 10140-3 and ISO 10140-4, cancels and replaces ISO 140-1:1997, ISO 140-3:1995, ISO 140-6:1998, ISO 140-8:1997, ISO 140-10:1991, ISO 140-11:2005 and ISO 140-16:2006, which have been technically revised. It also incorporates the Amendments ISO 140-1:1997/Amd.1:2004 and ISO 140-3:1995/Amd.1:2004. ISO 10140 consists of the following parts, under the general title Acoustics — Laboratory measurement of sound insulation of building elements: ⎯ Part 1: Application rules for specific products ⎯ Part 2: Measurement of airborne sound insulation ⎯ Part 3: Measurement of impact sound insulation ⎯ Part 4: Measurement procedures and requirements ⎯ Part 5: Requirements for test facilities and equipment
ISO 10140-5:2010(E) © ISO 2010 – All rights reserved v Introduction ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements (see Table 1). ISO 10140-1 specifies the application rules for specific elements and products, including specific requirements for preparation, mounting, operating and test conditions. ISO 10140-2 and ISO 10140-3 contain the general procedures for airborne and impact sound insulation measurements, respectively, and refer to ISO 10140-4 and this part of ISO 10140 where appropriate. For elements and products without a specific application rule described in ISO 10140-1, it is possible to apply ISO 10140-2 and ISO 10140-3. ISO 10140-4 contains basic measurement techniques and processes. This part of ISO 10140 contains requirements for test facilities and equipment. For the structure of ISO 10140 (all parts), see Table 1. ISO 10140 (all parts) was created to improve the layout for laboratory measurements, ensure consistency and simplify future changes and additions regarding mounting conditions of test elements in laboratory and field measurements. It is intended for ISO 10140 (all parts) to present a well-written and arranged format for laboratory measurements. It is intended to update ISO 10140-1 with application rules for other products. It is also intended to incorporate ISO 140-18 into ISO 10140 (all parts). SIST EN ISO 10140-5:2010
ISO 10140-5:2010(E) vi © ISO 2010 – All rights reserved Table 1 — Structure and contents of ISO 10140 (all parts) Relevant part of ISO 10140 Main purpose, contents and use Detailed content ISO 10140-1 It indicates the appropriate test procedure for elements and products. For certain types of element/product, it can contain additional and more specific instructions about quantities and test element size and about preparation, mounting and operating conditions. Where no specific details are included, the general guidelines are according to ISO 10140-2 and ISO 10140-3. Appropriate references to ISO 10140-2 and ISO 10140-3 and product-related, specific and additional instructions on: ⎯ specific quantities measured; ⎯ size of test element; ⎯ boundary and mounting conditions; ⎯ conditioning, testing and operating conditions; ⎯ additional specifics for test report. ISO 10140-2 It gives a complete procedure for airborne sound insulation measurements according to ISO 10140-4 and ISO 10140-5. For products without specific application rules, it is sufficiently complete and general for the execution of measurements. However, for products with specific application rules, measurements are carried out according to ISO 10140-1, if available.⎯ Definitions of main quantities measured ⎯ General mounting and boundary conditions ⎯ General measurement procedure ⎯ Data processing ⎯ Test report (general points) ISO 10140-3 It gives a complete procedure for impact sound insulation measurements according to ISO 10140-4 and ISO 10140-5. For products without specific application rules, it is sufficiently complete and general for the execution of measurements. However, for products with specific application rules, measurements are carried out according to ISO 10140-1, if available.⎯ Definitions of main quantities measured ⎯ General mounting and boundary conditions ⎯ General measurement procedure ⎯ Data processing ⎯ Test report (general points) ISO 10140-4 It gives all the basic measurement
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.