iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14540:2004

(Main)

Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 15 mm to 52 mm.
The standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of -20 °C in normal conditions, and a minimum temperature of -30 °C in colder climatic conditions.
Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671-2 can conform to the requirements of this Standard or prEN 1924, but prEN 1924 is preferred in these applications.
NOTE   All pressures are gauge pressures and are expressed in megapascals .

Feuerlöschläuche - Druckschlauche für Wandhydranten

Diese Europäische Norm legt die Anforderungen und Prüfverfahren für Druckschläuche für Wandhydranten fest. Die Schläuche sind für den Einsatz bei einem maximalen Arbeitsdruck von 1,5 MPa und für Innendurchmesser von 15 mm bis 52 mm vorgesehen.
Die Norm gilt ausschließlich für Schläuche für Feuerlöschzwecke, die für den Einsatz bei einer niedrigsten Temperatur von -20 °C unter normalen Bedingungen und einer niedrigsten Temperatur von -30 °C bei kälteren klimatischen Bedingungen vorgesehen sind.
Schläuche, die dieser Norm entsprechen, sollten mit Feuerlöschschlauchkupplungen verwendet werden, die den jeweiligen nationalen Normen für Kupplungen entsprechen.
Schläuche für den Einsatz auf Schiffen und/oder in aggressiven Umgebungen bei Verwendung in Wandhydranten nach EN 671-2 können entweder den Anforderungen dieser Norm oder von prEN 1924 entsprechen, jedoch ist prEN 1924 bei diesen Anwendungen vorzuziehen.
ANMERKUNG    Alle Drücke sind Manometerdrücke und werden in Megapascal angegeben. )

Tuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systèmes fixes

La présente Norme européenne spécifie les prescriptions et méthodes d'essai relatives aux tuyaux aplatissables étanches pour systèmes fixes. Ces tuyaux sont destinés à être utilisés à une pression maximale de 1,5 MPa et dans une plage de diamètres comprise entre 15 mm et 52 mm.
La norme s'applique exclusivement aux tuyaux de lutte contre l'incendie destinés à être utilisés à une température minimale de - 20 °C dans des conditions normales, et à une température minimale de - 30 °C dans des conditions climatiques plus froides.
Il convient que les tuyaux conformes à la présente norme soient utilisés avec des raccords type incendie conformes aux normes nationales relatives à ces raccords.
Si les tuyaux pour applications marines et/ou environnements agressifs doivent être utilisés avec des postes d'eau muraux tels que spécifiés dans l'EN 671-2, ils peuvent être conformes aux prescriptions énoncées dans la présente norme ou le prEN 1924, le prEN 1924 étant le plus approprié pour ces applications.
NOTE   Toutes les pressions sont des pressions manométriques et sont exprimées en mégapascals  ).

Gasilske cevi – Gasilske poltoge tlačne cevi za vgrajene sisteme

General Information

Status
Withdrawn
Publication Date
11-May-2004
Withdrawal Date
10-Apr-2007
ICS
13.220.10 - Fire-fighting
23.040.70 - Hoses and hose assemblies
Technical Committee
CEN/TC 192 - Fire service equipment
Drafting Committee
CEN/TC 192/WG 1 - Hoses for firefighting
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
11-Apr-2007
Completion Date
11-Apr-2007
Directive
2014/90/EU - Directive 2014/90/EU of the European Parliament and of the Council of 23 July 2014 on marine equipment and repealing Council Directive 96/98/EC
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
96/98/EC - Marine equipment
Ref Project
SIST EN 14540:2004 - Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

Relations

Merged Into
EN 14540:2004+A1:2007 - Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
Effective Date
18-Jan-2023

Buy Standard

EN 14540:2004EN 14540:2004
PreviousNext
Standard
EN 14540:2004
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fire-fighting hoses - Non-percolating layflat hoses for fixed systemsTuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systemes fixesFeuerlöschläuche - Druckschlauche für WandhydrantenTa slovenski standard je istoveten z:EN 14540:2004SIST EN 14540:2004en23.040.70Gumene cevi in armatureHoses and hose assemblies13.220.10Gašenje požaraFire-fightingICS:SLOVENSKI
STANDARDSIST EN 14540:200401-julij-2004

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14540May 2004ICS 13.220.10; 23.040.70English versionFire-fighting hoses - Non-percolating layflat hoses for fixedsystemsTuyaux de lutte contre l'incendie - Tuyaux aplatissablesétanches pour systèmes fixesFeuerlöschschläuche - Flachschläuche für WandhydrantenThis European Standard was approved by CEN on 1 August 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14540:2004: E

Kink pressure test.10A.1Principle.10A.2Test piece.10A.3Apparatus.10A.4Procedure.10A.5Test report.10Annex B (normative)
Accelerated ageing test.11B.1Test piece.11B.2Procedure.11Annex C (normative)
Low temperature flexibility test.12C.1Test piece.12C.2Apparatus.12C.3Procedure.16C.4Test report.16Annex D (normative)
Hot surface resistance test.17D.1Test piece.17D.2Apparatus.17D.3Procedure.20D.4Test report.20Annex E (normative)
Test for resistance to kinking.21E.1Test piece.21E.2Apparatus.21E.3Procedure.22E.4Test report.22Annex F (informative)
Recommended minimum frequencies of testing.23Bibliography.24

1 1 MPa = 10 bar
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 694:2014(Main)
Fire-fighting hoses - Semi-rigid hoses for fixed systems
SIST EN 694:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter.
Hoses conforming to this European Standard are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20°C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14540:2014(Main)
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
SIST EN 14540:2014

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °C in normal conditions, and a minimum temperature of −30 °C in colder climatic conditions and a maximum ambient temperature of +60 °C. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671 2 can conform to the requirements of this standard.
NOTE 2   All pressures are gauge pressures and are expressed in megapascals .

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1947:2014(Main)
Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
SIST EN 1947:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4).
This European Standard applies to hoses for fire-fighting purposes intended for use at ambient conditions within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.5 and identified by their marking in Clause 8 h).
Hoses conforming to this standard are intended for use with fire hose couplings conforming to the relevant national standards for couplings.’
Requirements are also given for hose assemblies (see Clause 9) where these are fitted by the hose manufacturer.
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15889:2011(Main)
Fire-fighting hoses - Test methods
SIST EN 15889:2012

This European standard specifies test methods for lay-flat fire-fighting hoses for fixed systems, semi-rigid fire-fighting hoses for both fixed systems and vehicles and fire-fighting suction hoses for vehicles.
These test methods are required for the standards for fire-fighting hose product standards developed by CEN/TC 192. Consequently, the applicable test methods are selected and the requirements and test values defined in the relevant fire-fighting hose product standards and normatively referenced in those standards.
This European Standard does not cover test methods for lay-flat fire-fighting hoses for vehicles for which no European standard exists.
NOTE   Annex R (informative) lists the existing published ISO and EN hose test methods standards that are specified within fire-fighting hose standards.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 694:2014(Main)
Fire-fighting hoses - Semi-rigid hoses for fixed systems
SIST EN 694:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter.
Hoses conforming to this European Standard are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20°C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14540:2014(Main)
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
SIST EN 14540:2014

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °C in normal conditions, and a minimum temperature of −30 °C in colder climatic conditions and a maximum ambient temperature of +60 °C. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671 2 can conform to the requirements of this standard.
NOTE 2   All pressures are gauge pressures and are expressed in megapascals .

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1947:2014(Main)
Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
SIST EN 1947:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4).
This European Standard applies to hoses for fire-fighting purposes intended for use at ambient conditions within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.5 and identified by their marking in Clause 8 h).
Hoses conforming to this standard are intended for use with fire hose couplings conforming to the relevant national standards for couplings.’
Requirements are also given for hose assemblies (see Clause 9) where these are fitted by the hose manufacturer.
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15889:2011(Main)
Fire-fighting hoses - Test methods
SIST EN 15889:2012

This European standard specifies test methods for lay-flat fire-fighting hoses for fixed systems, semi-rigid fire-fighting hoses for both fixed systems and vehicles and fire-fighting suction hoses for vehicles.
These test methods are required for the standards for fire-fighting hose product standards developed by CEN/TC 192. Consequently, the applicable test methods are selected and the requirements and test values defined in the relevant fire-fighting hose product standards and normatively referenced in those standards.
This European Standard does not cover test methods for lay-flat fire-fighting hoses for vehicles for which no European standard exists.
NOTE   Annex R (informative) lists the existing published ISO and EN hose test methods standards that are specified within fire-fighting hose standards.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-5:2024(Main)
Paints and varnishes - Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2024)
kSIST FprEN ISO 19403-5:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids by optical methods. The method can be applied for the characterization of liquid coating materials.
If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day