iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14540:2004

(Main)

Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 15 mm to 52 mm.
The standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of -20 °C in normal conditions, and a minimum temperature of -30 °C in colder climatic conditions.
Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671-2 can conform to the requirements of this Standard or prEN 1924, but prEN 1924 is preferred in these applications.
NOTE   All pressures are gauge pressures and are expressed in megapascals .

Feuerlöschläuche - Druckschlauche für Wandhydranten

Diese Europäische Norm legt die Anforderungen und Prüfverfahren für Druckschläuche für Wandhydranten fest. Die Schläuche sind für den Einsatz bei einem maximalen Arbeitsdruck von 1,5 MPa und für Innendurchmesser von 15 mm bis 52 mm vorgesehen.
Die Norm gilt ausschließlich für Schläuche für Feuerlöschzwecke, die für den Einsatz bei einer niedrigsten Temperatur von -20 °C unter normalen Bedingungen und einer niedrigsten Temperatur von -30 °C bei kälteren klimatischen Bedingungen vorgesehen sind.
Schläuche, die dieser Norm entsprechen, sollten mit Feuerlöschschlauchkupplungen verwendet werden, die den jeweiligen nationalen Normen für Kupplungen entsprechen.
Schläuche für den Einsatz auf Schiffen und/oder in aggressiven Umgebungen bei Verwendung in Wandhydranten nach EN 671-2 können entweder den Anforderungen dieser Norm oder von prEN 1924 entsprechen, jedoch ist prEN 1924 bei diesen Anwendungen vorzuziehen.
ANMERKUNG    Alle Drücke sind Manometerdrücke und werden in Megapascal angegeben. )

Tuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systèmes fixes

La présente Norme européenne spécifie les prescriptions et méthodes d'essai relatives aux tuyaux aplatissables étanches pour systèmes fixes. Ces tuyaux sont destinés à être utilisés à une pression maximale de 1,5 MPa et dans une plage de diamètres comprise entre 15 mm et 52 mm.
La norme s'applique exclusivement aux tuyaux de lutte contre l'incendie destinés à être utilisés à une température minimale de - 20 °C dans des conditions normales, et à une température minimale de - 30 °C dans des conditions climatiques plus froides.
Il convient que les tuyaux conformes à la présente norme soient utilisés avec des raccords type incendie conformes aux normes nationales relatives à ces raccords.
Si les tuyaux pour applications marines et/ou environnements agressifs doivent être utilisés avec des postes d'eau muraux tels que spécifiés dans l'EN 671-2, ils peuvent être conformes aux prescriptions énoncées dans la présente norme ou le prEN 1924, le prEN 1924 étant le plus approprié pour ces applications.
NOTE   Toutes les pressions sont des pressions manométriques et sont exprimées en mégapascals  ).

Gasilske cevi – Gasilske poltoge tlačne cevi za vgrajene sisteme

General Information

Status
Withdrawn
Publication Date
11-May-2004
Withdrawal Date
10-Apr-2007
ICS
13.220.10 - Fire-fighting
23.040.70 - Hoses and hose assemblies
Technical Committee
CEN/TC 192 - Fire service equipment
Drafting Committee
CEN/TC 192/WG 1 - Hoses for firefighting
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
11-Apr-2007
Completion Date
11-Apr-2007
Directive
2014/90/EU - Directive 2014/90/EU of the European Parliament and of the Council of 23 July 2014 on marine equipment and repealing Council Directive 96/98/EC
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
96/98/EC - Marine equipment
Ref Project
SIST EN 14540:2004 - Fire-fighting hoses - Non-percolating layflat hoses for fixed systems

Relations

Merged Into
EN 14540:2004+A1:2007 - Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
Effective Date
18-Jan-2023

Buy Standard

EN 14540:2004EN 14540:2004
PreviousNext
Standard
EN 14540:2004
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fire-fighting hoses - Non-percolating layflat hoses for fixed systemsTuyaux de lutte contre l'incendie - Tuyaux aplatissables étanches pour systemes fixesFeuerlöschläuche - Druckschlauche für WandhydrantenTa slovenski standard je istoveten z:EN 14540:2004SIST EN 14540:2004en23.040.70Gumene cevi in armatureHoses and hose assemblies13.220.10Gašenje požaraFire-fightingICS:SLOVENSKI
STANDARDSIST EN 14540:200401-julij-2004







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14540May 2004ICS 13.220.10; 23.040.70English versionFire-fighting hoses - Non-percolating layflat hoses for fixedsystemsTuyaux de lutte contre l'incendie - Tuyaux aplatissablesétanches pour systèmes fixesFeuerlöschschläuche - Flachschläuche für WandhydrantenThis European Standard was approved by CEN on 1 August 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14540:2004: E



EN 14540:2004 (E)2ContentsForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54Materials and construction of hose.65Dimensions, tolerances and maximum mass.65.1Inside diameter and maximum mass.65.2Length and tolerances on length.66Performance requirements of finished hose.76.1Hydrostatic requirements.76.1.1Deformation under normal working pressure.76.1.2Deformation under proof pressure.76.1.3Minimum burst pressure.86.1.4Kink pressure.86.2Adhesion.86.3Accelerated ageing.86.4Low temperature flexibility.86.5Hot surface resistance.86.6Resistance to kinking.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 694:2014(Main)
Fire-fighting hoses - Semi-rigid hoses for fixed systems
SIST EN 694:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter.
Hoses conforming to this European Standard are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20°C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14540:2014(Main)
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
SIST EN 14540:2014

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °C in normal conditions, and a minimum temperature of −30 °C in colder climatic conditions and a maximum ambient temperature of +60 °C. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671 2 can conform to the requirements of this standard.
NOTE 2   All pressures are gauge pressures and are expressed in megapascals .

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1947:2014(Main)
Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
SIST EN 1947:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4).
This European Standard applies to hoses for fire-fighting purposes intended for use at ambient conditions within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.5 and identified by their marking in Clause 8 h).
Hoses conforming to this standard are intended for use with fire hose couplings conforming to the relevant national standards for couplings.’
Requirements are also given for hose assemblies (see Clause 9) where these are fitted by the hose manufacturer.
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15889:2011(Main)
Fire-fighting hoses - Test methods
SIST EN 15889:2012

This European standard specifies test methods for lay-flat fire-fighting hoses for fixed systems, semi-rigid fire-fighting hoses for both fixed systems and vehicles and fire-fighting suction hoses for vehicles.
These test methods are required for the standards for fire-fighting hose product standards developed by CEN/TC 192. Consequently, the applicable test methods are selected and the requirements and test values defined in the relevant fire-fighting hose product standards and normatively referenced in those standards.
This European Standard does not cover test methods for lay-flat fire-fighting hoses for vehicles for which no European standard exists.
NOTE   Annex R (informative) lists the existing published ISO and EN hose test methods standards that are specified within fire-fighting hose standards.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 694:2014(Main)
Fire-fighting hoses - Semi-rigid hoses for fixed systems
SIST EN 694:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working pressure of 1,2 MPa for hoses of 19 mm and 25 mm inside diameter and 0,7 MPa for hoses of 33 mm inside diameter.
Hoses conforming to this European Standard are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20°C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14540:2014(Main)
Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
SIST EN 14540:2014

This European Standard specifies the requirements and test methods for non-percolating layflat hoses for fixed systems. The hoses are intended for use at a maximum working pressure of 1,5 MPa over a range of inside diameters from 25 mm to 52 mm.
This European Standard applies exclusively to hoses for fire-fighting purposes intended for use at a minimum ambient temperature of −20 °C in normal conditions, and a minimum temperature of −30 °C in colder climatic conditions and a maximum ambient temperature of +60 °C. Hoses conforming to this standard should be used with fire hose couplings conforming to the relevant national standards for couplings.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.4 and identified by their marking in Clause 8 f).
Hoses in marine applications and/or aggressive environments to be used with wall hydrants as specified in EN 671 2 can conform to the requirements of this standard.
NOTE 2   All pressures are gauge pressures and are expressed in megapascals .

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1947:2014(Main)
Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
SIST EN 1947:2014

This European Standard specifies the requirements and test methods for semi-rigid hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working pressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes (see Clause 4).
This European Standard applies to hoses for fire-fighting purposes intended for use at ambient conditions within the temperature range −20 °C to +60 °C.
NOTE 1   Hoses for use at ambient temperatures below −20 °C can be supplied if they have been tested at the specified lower temperature in accordance with 6.5 and identified by their marking in Clause 8 h).
Hoses conforming to this standard are intended for use with fire hose couplings conforming to the relevant national standards for couplings.’
Requirements are also given for hose assemblies (see Clause 9) where these are fitted by the hose manufacturer.
NOTE 2   All pressures are expressed in megapascals. 1 MPa = 10 bar.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15889:2011(Main)
Fire-fighting hoses - Test methods
SIST EN 15889:2012

This European standard specifies test methods for lay-flat fire-fighting hoses for fixed systems, semi-rigid fire-fighting hoses for both fixed systems and vehicles and fire-fighting suction hoses for vehicles.
These test methods are required for the standards for fire-fighting hose product standards developed by CEN/TC 192. Consequently, the applicable test methods are selected and the requirements and test values defined in the relevant fire-fighting hose product standards and normatively referenced in those standards.
This European Standard does not cover test methods for lay-flat fire-fighting hoses for vehicles for which no European standard exists.
NOTE   Annex R (informative) lists the existing published ISO and EN hose test methods standards that are specified within fire-fighting hose standards.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day