EN 2435-001:2006

Aerospace series - Paints and varnishes - Corrosion resistant chromated two component cold curing primer - Part 001: Minimum requirements

This standard specifies the minimum requirements for a two-component, chromated epoxy or polyurethane, corrosion resistant primer which can be used with or without a finish for aerospace applications.
The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837, procedure A and ISO 3270. The ability of the material to be used for a specific application (e.g. alternative substrate, specific drying conditions, etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.

Luft- und Raumfahrt - Beschichtungsstoffe - Korrosionsbeständiger Zweikomponenten-Primer, kalthärtend, chromathaltig - Teil 001: Mindestanforderungen

Diese Norm legt die Mindestanforderungen an einen korrosionsbeständigen, chromathaltigen Zweikomponen¬ten Primer auf Epoxid  oder Polyurethanbasis fest, der mit oder ohne Deckbeschichtung in der Luft  und Raumfahrt verwendet werden kann.
Die in dieser Norm festgelegten Eigenschaften werden anhand definierter Probenkörper aus Aluminiumlegie¬rung ermittelt, die nach EN 3837, Verfahren A und ISO 3270 vorbereitet werden. Die Eignung des für eine bestimmte Anwendung zu verwendenden Materials (z. B. alternativer Trägerwerkstoff, bestimmte Trocknungs¬bedingungen usw.) ist durch zusätzliche Prüfungen bestimmen, um nachzuweisen, dass die Anforderungen dieser Norm erfüllt werden.

Série aérospatiale - Peintures et vernis - Peinture primaire anti-corrosion chromatée à deux composants polymérisant à température ambiante - Partie 001 : Exigences minimales

Aeronavtika - Barve in laki - Dvokomponentni temeljni premaz, korozijsko obstojen, kromiran, ki se suši pri sobni temperaturi - 001. del: Minimalne zahteve

General Information

• Status: Withdrawn
• Publication Date: 20-Jun-2006
• Withdrawal Date: 15-Feb-2022
• ICS: 49.040 - Coatings and related processes used in aerospace industry
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 16-Feb-2022
• Ref Project: SIST EN 2435-001:2009 - Aerospace series - Paints and varnishes - Corrosion resistant chromated two component cold curing primer - Part 001: Minimum requirements

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Barve in laki - Dvokomponentni temeljni premaz, korozijsko obstojen, kromiran, ki se suši pri sobni temperaturi - 001. del: Minimalne zahteveLuft- und Raumfahrt - Beschichtungsstoffe - Korrosionsbeständiger Zweikomponenten-Primer, kalthärtend, chromathaltig - Teil 001: MindestanforderungenSérie aérospatiale - Peintures et vernis - Peinture primaire anti-corrosion chromatée à deux composants polymérisant à température ambiante - Partie 001 : Exigences minimalesAerospace series - Paints and varnishes - Corrosion resistant chromated two component cold curing primer - Part 001: Minimum requirements49.040Prevleke in z njimi povezani postopki, ki se uporabljajo v letalski in vesoljski industrijiCoatings and related processes used in aerospace industryICS:Ta slovenski standard je istoveten z:EN 2435-001:2006SIST EN 2435-001:2009en,de01-julij-2009SIST EN 2435-001:2009SLOVENSKI
STANDARD



SIST EN 2435-001:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2435-001June 2006ICS 49.040 English VersionAerospace series - Paints and varnishes - Corrosion resistantchromated two component cold curing primer - Part 001:Minimum requirementsSérie aérospatiale - Peintures et vernis - Peinture primaireanti-corrosion chromatée à deux composants polymérisantà température ambiante - Partie 001 : Exigences minimalesLuft- und Raumfahrt - Anstrichstoffe -Korrosionsbeständiger Zweikomponenten-Grundanstrich,kalthärtend, chromathaltig - Teil 001:MindestanforderungenThis European Standard was approved by CEN on 27 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2435-001:2006: ESIST EN 2435-001:2009



EN 2435-001:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Definitions.4 4 Classification.4 5 Required characteristics.5 6 Designation.5 Annex A (normative)
Test methods.6
SIST EN 2435-001:2009



EN 2435-001:2006 (E) 3 Foreword This European Standard (EN 2435-001:2006) has been prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. Attention is drawn to the possibility that some of the elements of this docum
...