iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 812:1997

(Main)

Industrial bump caps

Industrial bump caps

This European Standard specifies physical and performance requirements, methods of test and marking requirements for industrial bump caps. Industrial bump caps are intended to provide protection to the wearer against the effects of striking  his head against hard, stationary objects with sufficient severity to cause laceration or other superficial injuries. They are not intended to provide protection against the effects of falling or thrown objects, or moving or suspended loads.  NOTE : An industrial bump cap should not  be confused with an industrial  safety  helmet as specified in EN 397.

Industrie-Anstoßkappe

Diese Europäische Norm legt physikalische Anforderungen und Leistungsanforderungen, Prüfverfahren und die Kennzeichnung von Industrie- Anstoßkappen fest. Industrie-Anstoßkappen dienen dem Kopfschutz des Trägers, wenn der Kopf so stark gegen harte, feststehende Gegenstände prallt, daß es zu einer Platzwunde oder anderen oberflächlichen Verletzungen bis hin zur Selbst-betäubung kommt. Anstoßkappen bieten keinen Schutz gegen die Wirkung fallender oder geworfener Gegenstände, oder sich bewegender oder herabhängender Lasten.

Casquettes anti-heurt pour l'industrie

La présente norme européenne spécifie les exigences physiques et de performance, les méthodes d'essai et les exigences de marquage des casquettes anti-heurt pour l'industrie. Les casquettes anti-heurt pour l'industrie sont destinées à protéger le porteur lorsque sa tête vient heurter des objets durs et immobiles avec suffisamment de force pour provoquer des lacérations ou autres blessures superficielles. Elles ne sont pas destinées à protéger des effets des projections ou chutes d'objets ou des charges en suspension ou en mouvement.

Lahke industrijske čelade za varovanje pred udarci

General Information

Status
Withdrawn
Publication Date
21-Oct-1997
Withdrawal Date
31-Jan-2012
ICS
13.340.10 - Protective clothing
Technical Committee
CEN/TC 158 - Head protection
Drafting Committee
CEN/TC 158/WG 1 - Industrial safety helmets
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Feb-2012
Completion Date
01-Feb-2012
Directive
89/686/EEC - Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment
Mandate
M/BC/CEN/90/2 - Order for standardization concerning Personal Protective Equipment (P.P.E.)
Ref Project
SIST EN 812:1998 - Industrial bump caps

Relations

Replaced By
EN 812:2012 - Industrial bump caps
Effective Date
08-Feb-2012
Amended By
EN 812:1997/A1:2001 - Industrial bump caps
Effective Date
08-Jun-2022

Buy Standard

EN 812:1998EN 812:1998
PreviousNext
Standard
EN 812:1998
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-1998
/DKNHLQGXVWULMVNHþHODGH]DYDURYDQMHSUHGXGDUFL
Industrial bump caps
Industrie-Anstoßkappe
Casquettes anti-heurt pour l'industrie
Ta slovenski standard je istoveten z: EN 812:1997
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 812:2012(Main)
Industrial bump caps
SIST EN 812:2012

This European Standard specifies physical and performance requirements, methods of test and marking requirements for industrial bump caps.
Industrial bump caps are intended to provide protection to the wearer against the effects of striking his head against hard, stationary objects with sufficient severity to cause laceration or other superficial injuries. They are not intended to provide protection against the effects of falling or thrown objects, or moving or suspended loads.
NOTE   An industrial bump cap should not be confused with an industrial safety helmet, as specified in EN 397.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13997:2024(Main)
Protective clothing - Mechanical properties - Determination of resistance to cutting by sharp objects (ISO 13997:2024)
oSIST prEN ISO 13997:2024

This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13506-2:2024(Main)
Protective clothing against heat and flame - Part 2: Skin burn injury prediction - Calculation requirements and test cases (ISO 13506-2:2024)
SIST EN ISO 13506-2:2024

This document provides technical details for calculating predicted burn injury to human skin when its surface is subject to a varying heat flux, such as may occur due to energy transmitted through and by a garment or protective clothing ensemble exposed to flames. A series of test cases are provided against which the burn injury prediction calculation method is verified. It also contains requirements for the in situ calibration of the thermal energy sensor — skin injury prediction system for the range of heat fluxes that occur under garments.
The skin burn injury calculation methods as presented in this test method do not include terms for handling short wavelength radiation that may penetrate the skin. The latter include arc flashes, some types of fire exposures with liquid or solid fuels, and nuclear sources.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13506-1:2024(Main)
Protective clothing against heat and flame - Part 1: Test method for complete garments - Measurement of transferred energy using an instrumented manikin (ISO 13506-1:2024)
SIST EN ISO 13506-1:2024

This document specifies the overall requirements, equipment and calculation methods to provide results that can be used for evaluating the performance of complete garments or protective clothing ensembles exposed to short duration flame engulfment.
This test method establishes a rating system to characterize the thermal protection provided by single-layer and multi-layer garments made of flame resistant materials. The rating is based on the measurement of heat transfer to a full-size manikin exposed to convective and radiant energy in a laboratory simulation of a fire with controlled heat flux, duration and flame distribution. The heat transfer data is summed over a prescribed time to give the total transferred energy. Transferred energy and thermal manikin protection factor (TMPF) assessment methods provide a means to quantify product performance.
The exposure heat flux is limited to a nominal level of 84 kW/m2 and durations of 3 s to 20 s dependant on the risk assessment and expectations from the thermal insulating capability of the garment.
The results obtained apply only to the particular garments or ensembles, as tested, and for the specified conditions of each test, particularly with respect to the heat flux, duration and flame distribution.
This test method covers visual evaluation, observation, inspection and documentation on the overall behaviour of the test specimen(s) before, during and after the exposure. The effects of body position and movement are not addressed in this test method.
The heat flux measurements can also be used to calculate the predicted skin burn injury resulting from the exposure (see ISO 13506-2).
This test method does not simulate high radiant exposures such as those found in arc flash exposures, some types of fire exposures where liquid or solid fuels are involved, nor exposure to nuclear explosions.
NOTE            This test method is complex and requires a high degree of technical expertise in both the test setup and operation. Even minor deviations from the instructions in this test method can lead to significantly different test results.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17491-4:2024(Main)
Protective clothing - Test methods for clothing providing protection against chemicals - Part 4: Determination of resistance to penetration by a spray of liquid (spray test) (ISO 17491-4:2024)
SIST EN ISO 17491-4:2024

This document specifies the test method for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity:
a)       Method A: low-level spray test. This is applicable to clothing that covers the full body surface and is intended to be worn when there is a potential risk of exposure to small quantities of spray or accidental low-volume splashes of a liquid chemical.
b)       Method B: high-level spray test. This is applicable to clothing with spray-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment, which covers the full body surface and which is intended to be worn when there is a risk of exposure to sprayed liquid chemical.
This document does not apply to chemical permeation resistance of the materials from which the chemical protective clothing is made.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14325:2018+A1:2024(Main + Amendment)
Protective clothing against chemicals - Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages
SIST EN 14325:2018+A1:2024

This European Standard specifies the performance classification and test methods for materials used in chemical protective clothing, including gloves and footwear. The gloves and boots should have the same chemical protective barrier requirements as the fabric when an integral part of the clothing. This is a reference standard to which chemical protective clothing performance standards may refer in whole or in part, but this standard is not exhaustive in the sense that product standards may well require testing according to test method standards which are not included in this standard.
While these performance levels are intended to relate to the usage to which the chemical protective clothing is to be put, it is essential that the chemical protective clothing manufacturer or supplier indicate the intended use of the protective clothing and that the user (specifier) carries out a risk assessment in order to establish the correct performance level for the intended task.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24231:2024(Main)
Protective clothing - Protection against rain - Test method for ready-made garments against high-energy droplets from above (ISO 24231:2024)
SIST EN ISO 24231:2024

This document specifies a test method for determining the liquid tightness of clothing for protection against rain, using a static manikin exposed to large amount of high energy droplets from above. It is applicable to the testing of jackets, trousers, coats and one- or two-piece suits.
This document is not applicable to the testing of garments for resistance to other weather conditions, e.g. snow, hail-, or strong winds.
NOTE            For general background of the rain simulation, see Annex A.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11610:2023(Main)
Protective clothing - Vocabulary (ISO 11610:2023)
SIST EN ISO 11610:2023

This document contains a list of terms which are frequently used in the standardization of protective clothing (5.1.4) and protective equipment worn on the body, including hand and arm protection and lifejackets, and definitions of these terms.
The definitions are intended to support an unambiguous use of the terms listed.
This document is intended to serve as a reference document for the Working Groups of CEN/TC 162 and ISO/TC 94/SC 13 to ascertain what definitions already exist and may be used for setting up new standards and to provide guidance in the elaboration of new definitions.
NOTE - In addition to text written in the official ISO languages (English, French), this document gives text in German. This text is published under the responsibility of the Member Body for Germany (DIN) and is given for information only. Only the text given in the official lan­guages can be considered as ISO text.

  • Standard
    83 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    160 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4863:2023(Main)
Aerospace series - Rotorcraft immersion suits - Requirements, testing and marking
SIST EN 4863:2023

This document specifies requirements for immersion suits for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It applies to immersion suits for use by adults only.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4862:2023(Main)
Aerospace series - Rotorcraft constant wear lifejackets - Requirements, testing and marking
SIST EN 4862:2023

This document specifies requirements for constant wear lifejackets for use by helicopter crew members and passengers in the event of a ditching or water impact, to ensure minimum levels of performance. It only applies to constant wear lifejackets for use by adults and that are intended to be manually inflated after leaving the helicopter.
Helicopter constant wear lifejackets are sometimes designed to be worn with or without a helicopter immersion suit and/or emergency breathing system.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day