EN ISO 8673:2012
(Main)Hexagon regular nuts (style 1) with metric fine pitch thread - Product grades A and B (ISO 8673:2012)
Hexagon regular nuts (style 1) with metric fine pitch thread - Product grades A and B (ISO 8673:2012)
ISO 8673:2012 specifies the geometry of hexagon nuts with nominal thread diameter from 8 mm up to and including 64 mm and the mechanical properties of hexagon regular nuts (style 1) with metric fine pitch thread in product grade A for nominal thread diameters 8 mm less than or equal to D less than or equal to 16 mm and in product grade B for nominal diameters 16 mm less than D less than or equal to 39 mm.
Sechskantmuttern (Typ 1) mit metrischem Feingewinde - Produktklassen A und B (ISO 8673:2012)
Diese Internationale Norm legt die Geometrie von Sechskantmuttern mit Gewindenenndurchmessern von 8 mm bis 64 mm und die mechanischen Eigenschaften von Sechskantmuttern (Typ 1) mit metrischem Fein-gewinde in Produktklasse A für Gewindenenndurchmesser 8 mm D 16 mm und in Produktklasse B für Gewindenenndurchmesser 16 mm < D 39 mm fest.
Falls in besonderen Fällen andere Festlegungen als die in dieser Internationalen Norm aufgeführten benötigt werden, können diese den entsprechenden Internationalen Normen entnommen werden, z. B. ISO 724, ISO 898 2, ISO 965 1, ISO 3506 2 und ISO 4759 1.
ANMERKUNG Da die Höhe der Mutter aufgrund des Feingewindes unzureichend ist, besteht eine erhöhte Wahr-scheinlichkeit für das Abstreifen des Gewindes. Daher werden vorzugsweise hohe Muttern (Typ 2) nach ISO 8674 ver-wendet.
Écrous hexagonaux normaux (style 1) à filetage métrique à pas fin - Grades A et B (ISO 8673:2012)
L'ISO 8673:2012 spécifie la géométrie des écrous hexagonaux de diamètre nominal de filetage de 8 mm à 64 mm inclus et les caractéristiques mécaniques des écrous hexagonaux normaux (style 1) à filetage métrique à pas fin de grade A pour les diamètres nominaux de filetage 8 £ D £ 16 mm et de grade B pour les diamètres nominaux 16 D £ 39 mm.
Šestrobe matice, tip 1, z metrskim drobnim navojem - Razreda izdelave A in B (ISO 8673:2012)
Ta mednarodni standard določa geometrijo šestrobih nizkih matic z nazivnimi premeri navoja od 8 mm do vključno 64 mm in mehanične lastnosti šestrobnih matic (tip 1) z metrskim drobnim navojem razreda izdelave A za nazivne premere navoja 8 mm ≤ D ≤ 16 mm in razredom izdelave B za nazivne premere navoja 16 mm < D ≤ 39 mm. Če so v posebnih primerih zahtevane specifikacije, ki niso navedene v tem mednarodnem standardu, jih je mogoče izbrati iz obstoječih mednarodnih standardov, na primer standardov ISO 724, ISO 898-2, ISO 965-1, ISO 3506-2 in ISO 4759-1. OPOMBA Ker zaradi drobnega navoja matice niso dovolj visoke, obstaja večja verjetnost, da se navoj pobere. Zato se priporoča uporaba visokih matic (tip 2) v skladu s standardom ISO 8674.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2013
1DGRPHãþD
SIST EN ISO 8673:2002
Šestrobe matice, tip 1, z metrskim drobnim navojem - Razreda izdelave A in B (ISO
8673:2012)
Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO
8673:2012)
Sechskantmuttern, Typ 1, mit metrischem Feingewinde - Produktklassen A und B (ISO
8673:2012)
Écrous hexagonaux, style 1, à filetage métrique à pas fin - Grades A et B (ISO
8673:2012)
Ta slovenski standard je istoveten z: EN ISO 8673:2012
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 8673
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 21.060.20 Supersedes EN ISO 8673:2000
English Version
Hexagon regular nuts (style 1) with metric fine pitch thread -
Product grades A and B (ISO 8673:2012)
Écrous hexagonaux normaux (style 1) à filetage métrique à Sechskantmuttern, Typ 1, mit metrischem Feingewinde -
pas fin - Grades A et B (ISO 8673:2012) Produktklassen A und B (ISO 8673:2012)
This European Standard was approved by CEN on 15 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8673:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 8673:2012) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8673:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8673:2012 has been approved by CEN as a EN ISO 8673:2012 without any modification.
INTERNATIONAL ISO
STANDARD 8673
Third edition
2012-12-15
Hexagon regular nuts (style 1) with metric
fine pitch thread — Product grades A and B
Écrous hexagonaux normaux (style 1) à filetage métrique à pas fin —
Grades A et B
Reference number
ISO 8673:2012(E)
©
ISO 2012
ISO 8673:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 8673:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Dimensions . 2
4 Requirements and reference International Standards . 4
5 Designation . 4
Bibliography . 5
ISO 8673:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8673 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with
metric internal thread.
This third edition cancels and replaces the second edition (ISO 8673:1999), of which it constitutes a minor revision.
iv © ISO 2012 – All rights reserved
ISO 8673:2012(E)
Introduction
This International Standard belongs to a complete group of product standards developed by ISO on external
hexagon drive fasteners. It comprises the following:
a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042,
ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);
d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);
e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670).
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.