EN ISO 22476-8:2018

Geotechnical investigation and testing - Field testing - Part 8: Full displacement pressuremeter test (ISO 22476-8:2018)

This document specifies the equipment requirements, execution of and reporting on full displacement pressuremeter (FDP) tests.
NOTE       This document fulfils the requirements for full displacement pressurementer test as part of the geotechnical investigation services according to EN 1997-1 and EN 1997-2.
Tests with the full displacement pressuremeter cover the measurement in situ of the deformation of soils and weak rocks by the expansion/contraction of a cylindrical flexible membrane under pressure.

Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 8: Versuch mit dem Verdrängungspressiometer (ISO 22476-8:2018)

Dieses Dokument legt die Geräteanforderungen, die Durchführung und die Ergebnisdarstellung von Versuchen mit dem Verdrängungspressiometer (en: full displacement pressuremeter, FDP) fest.
ANMERKUNG   Dieses Dokument erfüllt die Anforderungen an den Versuch mit dem Verdrängungspressiometer als Teil der geotechnischen Erkundung nach EN 1997 1 und EN 1997 2.
Versuche mit dem Verdrängungspressiometer umfassen die Messung der Verformung von Böden und weichem Fels in situ anhand der Aufweitung und Kontraktion einer flexiblen zylindrischen Membran unter Druck.

Reconnaissance et essais géotechniques - Essais en place - Partie 8: Essai au pressiomètre refoulant (ISO 22476-8:2018)

Le présent document spécifie les exigences relatives à l'appareillage, à l'exécution et au compte rendu des essais au pressiomètre refoulant (FDP).
NOTE       Ce document satisfait aux exigences relatives aux essais au pressiomètre refoulant dans le cadre des services de reconnaissance géotechnique selon les normes EN 1997‑1 et EN 1997‑2.
Les essais au pressiomètre refoulant couvre la mesure in situ la déformation d'un sol ou d'une roche tendre produite par l'expansion/la contraction d'une sonde cylindrique à membrane souple sous l'effet de la pression.

Geotehnično preiskovanje in preskušanje - Preskušanje na terenu - 8. del: Preskus z vtiskovanim presiometrom (ISO 22476-8:2018)

Ta dokument zajema zahteve za preiskovanje zemljine in šibkih kamnin s preskusi z vtiskovanim presiometrom (FDP) kot del storitev geotehničnega preiskovanja v skladu s standardoma EN 1997-1 in EN 1997-2. Preskusi z vtiskovanim presiometrom zajemajo meritve deformacije zemljin in šibkih kamnin na kraju samem s širjenjem in krčenjem valjaste fleksibilne membrane pod tlakom. Vtiskovani presiometer se vtisne v tla z vgrajenim stožcem na spodnji strani in tako ustvari lastno preskusno luknjo. Oprema vtiskovanega presiometra je lahko v številnih različnih oblikah, zato so opisi podani v skladu z vrsto namestitve in sistemi merjenja.

General Information

• Status: Published
• Publication Date: 23-Oct-2018
• Withdrawal Date: 29-Apr-2019
• ICS: 93.020 - Earthworks. Excavations. Foundation construction. Underground works
• Technical Committee: CEN/TC 341 - Geotechnical Investigation and Testing
• Drafting Committee: CEN/TC 341/WG 5 - Borehole expansion tests
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 24-Oct-2018
• Due Date: 03-May-2019
• Completion Date: 24-Oct-2018
• Ref Project: SIST EN ISO 22476-8:2018 - Geotechnical investigation and testing - Field testing - Part 8: Full displacement pressuremeter test (ISO 22476-8:2018)

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
*HRWHKQLþQRSUHLVNRYDQMHLQSUHVNXãDQMH3UHVNXãDQMHQDWHUHQXGHO3UHVNXV
]YWLVNRYDQLPSUHVLRPHWURP,62
Geotechnical investigation and testing - Field testing - Part 8: Full displacement
pressuremeter test (ISO 22476-8:2018)
Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 8:
Vollverdrängungspressiometerversuch (ISO 22476-8:2018)
Reconnaissance et essais géotechniques - Essais en place - Partie 8: Essai au
pressiomètre refoulant (ISO 22476-8:2018)
Ta slovenski standard je istoveten z: EN ISO 22476-8:2018
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22476-8
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 93.020
English Version
Geotechnical investigation and testing - Field testing - Part
8: Full displacement pressuremeter test (ISO 22476-
8:2018)
Reconnaissance et essais géotechniques - Essais en Geotechnische Erkundung und Untersuchung -
place - Partie 8: Essai au pressiomètre refoulant (ISO Felduntersuchungen - Teil 8:
22476-8:2018) Vollverdrängungspressiometerversuch (ISO 22476-
8:2018)
This European Standard was approved by CEN on 1 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22476-8:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 22476-8:2018) has been prepared by Technical Committee ISO/TC 182
"Geotechnics" in collaboration with Technical Committee CEN/TC 341 “Geotechnical Investigation and
Testing” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22476-8:2018 has been approved by CEN as EN ISO 22476-8:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 22476-8
First edition
2018-09
Geotechnical investigation and
testing — Field testing —
Part 8:
Full displacement pressuremeter test
Reconnaissance et essais géotechniques — Essais en place —
Partie 8: Essai au pressiomètre refoulant
Reference number
ISO 22476-8:2018(E)
©
ISO 2018
ISO 22476-8:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 22476-8:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 1
3.1 Terms and definitions . 1
3.2 Symbols . 7
4 Equipment . 8
4.1 General . 8
4.2 Cone module . 8
4.3 Pressuremeter module . 9
4.4 Measuring system . 9
5 Test procedure . 9
5.1 Selection of equipment and procedures . 9
5.2 Preparation .10
5.3 Installation .10
5.4 Pressuremeter test .11
5.4.1 General.11
5.4.2 Optional test stages .11
5.4.3 Frequency of logging parameters .11
5.5 Test completion .11
6 Test results .11
7 Report .12
Annex A (informative) Uncertainties in pressuremeter testing .14
Annex B (normative) Calibrations .15
Annex C (normative) Corrections on the volume .16
Annex D (normative) Corrections on the pressure .19
Annex E (informative) Strain conversions .20
Bibliography .21
ISO 22476-8:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 341, Geotechnical investigation and testing, in collaboration with ISO Technical
Committee ISO/TC 182, Geotechnics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 22476 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved

INTERNATIONAL STANDARD ISO 22476-8:2018(E)
Geotechnical investigation and testing — Field testing —
Part 8:
Full displacement pressuremeter test
1 Scope
This document specifies the equipment requirements, execution of and reporting on full displacement
pressuremeter (FDP) tests.
NOTE This document fulfils the requirements for f
...