iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15216:2007

(Main)

Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates

Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates

This European standard specifies a method for the determination of total dissolved solids (TDS) in water and eluates, provided they are not volatile under the conditions specified or that they do not release water molecules from hydration. It applies to water and eluates containing more than 200 mg/l of total dissolved solids. Samples with lower amounts of dissolved solids can be analyzed by repetition of the drying step.

Charakterisierung von Abfällen - Bestimmung des Gesamtgehaltes an gelösten Feststoffen (TDS) in Wasser und Eluaten

Diese Europäische Norm legt ein Verfahren zur Bestimmung des Gesamtgehaltes an gelösten Feststoffen (TDS) in Wasser und Eluaten fest, sofern sie nicht unter den angegebenen Bedingungen flüchtig sind bzw. keine Wassermoleküle aus Kristallwasser freisetzen. Die Norm gilt für Wasser und Eluate mit einem Gesamt¬gehalt an gelösten Feststoffen von mehr als 200 mg/l. Proben mit niedrigerem Gehalt an gelösten Stoffen können durch Wiederholung des Trockenschritts analysiert werden.

Caractérisation des déchets - Détermination de la concentration en matières solides dissoutes totales (TDS) de l'eau et des éluats

Karakterizacija odpadkov - Določevanje celotnih raztopljenih snovi (TDS) v vodi in izlužkih

General Information

Status
Withdrawn
Publication Date
16-Oct-2007
Withdrawal Date
19-Oct-2021
ICS
13.030.20 - Liquid wastes. Sludge
Technical Committee
CEN/TC 444 - Environmental characterization
Drafting Committee
CEN/TC 444/WG 5 - Physical tests
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
20-Oct-2021
Mandate
M/326 - Standardization mandate to CEN for the development of standardized methods for the characterization of waste
Ref Project
SIST EN 15216:2008 - Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates

Relations

Replaced By
EN 15216:2021 - Environmental solid matrices - Determination of total dissolved solids (TDS) in water and eluates
Effective Date
27-Oct-2021

Buy Standard

EN 15216:2008EN 15216:2008
PreviousNext
Standard
EN 15216:2008
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.L]OXåNLKCharakterisierung von Abfällen - Bestimmung des Gesamtgehaltes an gelösten Feststoffen (TDS) in Wasser und EluatenCaractérisation des déchets - Détermination de la concentration en matiéres solides dissoutes totales (TDS) de l'eau et des éluatsCharacterization of waste - Determination of total dissolved solids (TDS) in water and eluates13.030.20Liquid wastes. SludgeICS:Ta slovenski standard je istoveten z:EN 15216:2007SIST EN 15216:2008en,fr,de01-februar-2008SIST EN 15216:2008SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15216October 2007ICS 13.030.20 English VersionCharacterization of waste - Determination of total dissolvedsolids (TDS) in water and eluatesCaractérisation des déchets - Détermination de laconcentration en matières solides dissoutes totales (TDS)de l'eau et des éluatsCharakterisierung von Abfällen - Bestimmung desGesamtgehaltes an gelösten Feststoffen (TDS) in Wasserund EluatenThis European Standard was approved by CEN on 1 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15216:2007: ESIST EN 15216:2008

Summary of general requirements and recommendations.8 Bibliography.9
EN 1521
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15216:2021(Main)
Environmental solid matrices - Determination of total dissolved solids (TDS) in water and eluates
SIST EN 15216:2022

This document specifies a method for the determination of total dissolved solids (TDS) in water and eluates (see Annex A), provided they are not volatile under the conditions specified or that they do not release water molecules from hydration. It applies to water and eluates containing more than 100 mg/l of total dissolved solids. Samples with lower amounts of dissolved solids can be analysed by repetition of the drying step.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 54321:2021(Main)
Soil, treated biowaste, sludge and waste - Digestion of aqua regia soluble fractions of elements (ISO 54321:2020)
SIST EN ISO 54321:2021

This document specifies two methods for digestion of soil, treated biowaste, sludge and waste by the use of an aqua regia digestion.
Digestion with aqua regia will not necessarily accomplish total decomposition of the sample. The extracted analyte concentrations may not necessarily reflect the total content in the sample but represent the aqua regia soluble metals under the condition of this test procedure. It is generally agreed that for environmental analysis purposes, the results are fit for the intended purpose to protect the environment.
This document is applicable for the following elements:
Aluminium (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), calcium (Ca), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), magnesium (Mg), manganese (Mn), mercury (Hg), molybdenum (Mo), nickel (Ni), phosphorus (P), potassium (K), selenium (Se), silver (Ag), sodium (Na), strontium (Sr), sulfur (S), tellurium (Te), thallium (Tl), tin (Sn), titanium (Ti), vanadium (V), and zinc (Zn).
This document can also be applied for the digestion of other elements, provided the user has verified the applicability.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17322:2020(Main)
Environmental Solid Matrices - Determination of polychlorinated biphenyls (PCB) by gas chromatography - mass selective detection (GC-MS) or electron-capture detection (GC-ECD)
SIST EN 17322:2020

This document specifies methods for quantitative determination of seven selected polychlorinated biphenyls (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153 and PCB180) in soil, sludge, sediment, treated biowaste, and waste using GC-MS and GC-ECD (see Table 2).
The limit of detection depends on the determinants, the equipment used, the quality of chemicals used for the extraction of the sample and the clean-up of the extract.
Under the conditions specified in this document, lower limit of application from 1 μg/kg (expressed as dry matter) for soils, sludge and biowaste to 10 μg/kg (expressed as dry matter) for solid waste can be achieved. For some specific samples the limit of 10 μg/kg cannot be reached.
Sludge, waste and treated biowaste may differ in properties, as well as in the expected contamination levels of PCB and presence of interfering substances. These differences make it impossible to describe one general procedure. This document contains decision tables based on the properties of the sample and the extraction and clean-up procedure to be used.
NOTE   The analysis of PCB in insulating liquids, petroleum products, used oils and aqueous samples is referred to in EN 61619, EN 12766-1 and EN ISO 6468 respectively.
The method can be applied to the analysis of other PCB congeners not specified in the scope, provided suitability is proven by proper in-house validation experiments.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-2:2006(Main)
Characterization of waste - Sampling of waste materials - Part 2: Guidance on sampling techniques
SIST-TP CEN/TR 15310-2:2007

This Technical Report describes techniques for sampling liquid and granular waste material, including paste-like materials and sludges, found in a variety of locations. The Technical Report provides information to allow the selection and preparation of equipment and apparatus to be used in the sampling activity.
NOTE 1   This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate.
NOTE 2    The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

  • Technical report
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-4:2006(Main)
Characterization of waste - Sampling of waste materials - Part 4: Guidance on procedures for sample packaging, storage, preservation, transport and delivery
SIST-TP CEN/TR 15310-4:2007

This Technical Report describes procedures for the packaging, preservation, short-term storage and transport of both solid and liquid waste samples, including paste-like substances and sludges. Where available and appropriate for field application, requirements for specific storage conditions and/or preservation methods should be selected from the chosen analytical standard and collaboration with the testing laboratory.
NOTE 1   This Technical Report provides a shop shelf of example sampling techniques that can be selected to meet a wide range of sampling situations. For a specific situation one of the presented procedures may be appropriate.
NOTE 2   The procedures listed in this Technical Report reflect current best practice, but these are not exhaustive and other procedures may be equally relevant.

  • Technical report
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-5:2006(Main)
Characterization of waste - Sampling of waste materials - Part 5: Guidance on the process of defining the sampling plan
SIST-TP CEN/TR 15310-5:2007

This Technical Report provides guidance on process of defining of a Sampling Plan based on the objective of the testing programme. It specifically deals with the strategic decisions that are needed, based on the sampling objective.
NOTE 1   Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence).
NOTE 2    The document provides considerable detail on current best practice, but is not exhaustive.
NOTE 3   To clarify the text, the document provides a number of worked examples.

  • Technical report
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 15310-1:2006(Main)
Characterization of waste - Sampling of waste materials - Part 1: Guidance on selection and application of criteria for sampling under various conditions
SIST-TP CEN/TR 15310-1:2007

This Technical Report discusses the statistical principles of sampling, and provides a number of statistical tools to assist in the design of testing programmes for application to sampling under various conditions.
NOTE 1   Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence).
NOTE 2   The document provides considerable detail on current best practice, but is not exhaustive.
NOTE 3   To clarify the text, the document provides a number of worked examples.

  • Technical report
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-4:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)
SIST EN 12457-4:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with limited size reduction. Note: In some cases, it could be useful to test the material with coarser particles up to 40 mm in diameter: This requires a larger amount for material and liquid.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-3:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction)
SIST EN 12457-3:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 2 l/kg dry matter and subsequently of 8 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12457-2:2002(Main)
Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction)
SIST EN 12457-2:2004

This part of the European Standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. The test procedure specified in this Standard produces an eluate which shall subsequently be characterised physically and chemically according to appropriate standard methods.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day