EN 14492-2:2019/prA1
(Amendment)Cranes - Power driven winches and hoists - Part 2: Power driven hoists
Cranes - Power driven winches and hoists - Part 2: Power driven hoists
This document is applicable to the design, information for use, maintenance and testing of power driven hoists, compact or open construction, with or without trolleys for which the prime mover is an electric, hydraulic or pneumatic motor. They are designed for the lifting and lowering of loads that are suspended on hooks or other load lifting attachments. Hoists can be used either in cranes, in other machines, e.g. rail dependent storage and retrieval equipment, monorail conveyors or by itself.
This document is applicable to the following types of hoist:
a) rope hoist;
b) chain hoist;
c) belt hoist, except belt hoist with steel belts as hoisting media;
d) NGL building hoists including supporting structures;
e) Winches used for lifting operation.
This document is not applicable of the following hazards:
f) this document does not cover hazards related to builders hoists for the transport of goods as defined in Noise Outdoor Directive (OND) 2000/14/EC;
g) this document does not cover hazards related to the lifting of persons.
This document does not specify additional requirements for hazards related to the use of hoists in explosive atmospheres in underground mines.
The significant hazards covered by this document are identified in Clause 4.
This document is not applicable to power driven hoists that are manufactured before the date of publication of this document by CEN.
Krane - Kraftgetriebene Winden und Hubwerke - Teil 2: Kraftgetriebene Hubwerke
Appareils de levage à charge suspendue - Treuils et palans motorises - Partie 2 : Palans et treuils de levage motorisés
Žerjavi - Motorni vitli in dvižni mehanizmi - 2. del: Motorni dvižni mehanizmi - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2022
Žerjavi - Motorni vitli in dvižni mehanizmi - 2. del: Motorni dvižni mehanizmi -
Dopolnilo A1
Cranes - Power driven winches and hoists - Part 2: Power driven hoists
Krane - Kraftgetriebene Winden und Hubwerke - Teil 2: Kraftgetriebene Hubwerke
Appareils de levage à charge suspendue - Treuils et palans motorises - Partie 2 : Palans
et treuils de levage motorisés
Ta slovenski standard je istoveten z: EN 14492-2:2019/prA1
ICS:
53.020.20 Dvigala Cranes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 14492-2:2019
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2022
ICS 53.020.20
English Version
Cranes - Power driven winches and hoists - Part 2: Power
driven hoists
Appareils de levage à charge suspendue - Treuils et Krane - Kraftgetriebene Winden und Hubwerke - Teil
palans motorises - Partie 2 : Palans et treuils de levage 2: Kraftgetriebene Hubwerke
motorisés
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 147.
This draft amendment A1, if approved, will modify the European Standard EN 14492-2:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14492-2:2019/prA1:2022 E
worldwide for CEN national Members.
prEN 14492-2:2019/prA1:2022 (E)
Contents Page
European foreword . 3
1 Modifications to the European foreword . 4
2 Modifications to the Introduction . 4
3 Modifications to Clause 1, "Scope" . 4
4 Modifications to Clause 2, "Normative references" . 5
5 Modifications to Clause 3, "Terms, definitions and symbols " . 7
6 Modifications to Clause 4, "List of significant hazards " . 8
7 Modifications to Clause 5, " Safety requirements and/or protective measures " . 8
8 Modifications to Clause 6, "Verification of the safety requirements and/or protective
measures" . 14
9 Modifications to Clause 7, "User information" . 15
10 Modifications to Annex B, "Classification" . 15
11 Modifications to Annex C, "Guidance on hoist classification" . 15
12 Modifications to Annex D, " Additional requirements for high risk applications" . 16
13 Modifications to Annex E, " Additional requirements for Power driven hoists designed for
holding stationary loads above persons" . 16
14 Modification to Annex F, "Additional requirements for hoists intended to be used in
potentially explosive atmospheres" . 16
15 Modification to Annex G, "Additional requirements for operation in aggressive
environments and outdoors". 17
16 Modifications to Annex I, " Supporting structures for NGL building hoists" . 17
17 Modifications to Annex J, "Power driven series hoist mechanisms – Test procedure for
verification of the classification". 18
18 Modifications to Annex L, " Number of starts and cyclic duration factor of motors" . 18
19 Modifications to Annex M, " Noise test code" . 19
20 Modifications to Annex N, "Design calculation parameters for chains" . 20
21 Modification to Annex O, " Selection of a suitable set of crane standards for a given
application" . 20
22 Modifications to Annex ZA, " Relationship between this European Standard and the
Essential Requirements of EU Directive 2006/42/EC aimed to be covered" . 20
23 Modifications to Annex ZB, " Relationship between this European Standard and the
Essential Requirements of EU Directive 2014/34/EU aimed to be covered" . 23
24 Modifications to the Bibliography . 24
prEN 14492-2:2019/prA1:2022 (E)
European foreword
This document (prEN 14492-2:2019/prA1:2022) has been prepared by Technical Committee
CEN/TC 147 “Cranes-Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association and supports essential requirements of
EU Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
prEN 14492-2:2019/prA1:2022 (E)
1 Modifications to the European foreword
th
Replace the 5 paragraph with the following:
"CEN/TC 147 WG 17 has reviewed EN 14492-2:2019 to adapt the standard to the technical progress, new
requirements and changes in standards referenced; the main topics are:
— the standard references in Clause 2 and in the Bibliography are all dated;
— the Annex ZA is updated.”.
2 Modifications to the Introduction
Replace the whole clause with the following:
"This document is a harmonized standard to provide one means for power driven hoists to conform to
the essential health and safety requirements of the EU Directive 2006/42/EC (Machinery) and essential
safety requirements of EU Directive 2014/34/EU (ATEX).
This document is a type C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered
are indicated in the scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or
type-B standards, the provisions of this type-C standard take precedence over the requirements of the
other standards, for machines that have been designed and built according to the requirements of this
type-C standard.".
3 Modifications to Clause 1, "Scope"
nd
Replace the 2 paragraph with the following:
"This document is applicable to the following types of hoists and applications:
a) rope hoists;
b) chain hoists;
prEN 14492-2:2019/prA1:2022 (E)
c) belt hoists, except belt hoists with steel belts as hoisting media;
d) NGL building hoists including supporting structures;
e) winches used for lifting operation;
f) hoists designed for holding stationary loads above persons;
g) hoists designed for high risk applications.".
nd
Add a new paragraph after the 2 one:
"This document does not apply to belt hoists with steel belts as hoisting media.".
rd th
Replace the existing 3 paragraph (now the 4 paragraph) with the following:
"This document is not applicable to the following hazards:
a) this document does not cover hazards related to builders hoists for the transport of goods as defined
in Noise Outdoor Directive (OND) 2000/14/EC;
b) this document does not cover hazards related to the lifting of persons.”.
4 Modifications to Clause 2, "Normative references"
Add dates to the following references in Clause 2 and throughout the text, as follows:
“EN 81-50:2020, Safety rules for the construction and installation of lifts — Examinations and tests — Part
50: Design rules, calculations, examinations and tests of lift components
EN 1127-1:2019, Explosive atmospheres — Explosion prevention and protection — Part 1: Basic concepts
and methodology
EN 12644-2:2000+A1:2008, Cranes — Information for use and testing — Part 2: Marking
EN 13001-1:2015, Cranes — General design — Part 1: General principles and requirements
EN 13001-2:2021, Crane safety — General design — Part 2: Load actions
EN 13001-3-1:2012+A2:2018, Cranes — General Design — Part 3-1: Limit States and proof competence of
steel structure
EN 13001-3-2:2014, Cranes — General design — Part 3-2: Limit states and proof of competence of wire
ropes in reeving systems
EN 13001-3-3:2014, Cranes — General design — Part 3-3: Limit states and proof of competence of
wheel/rail contacts
EN 13001-3-5:2016, Cranes — General design — Part 3-5: Limit states and proof of competence of forged
hooks
EN 13135:2013+A1:2018, Cranes — Safety — Design — Requirements for equipment
prEN 14492-2:2019/prA1:2022 (E)
EN 13411-3:2004+A1:2008, Terminations for steel wire ropes — Safety — Part 3: Ferrules and ferrule-
securing
EN 13411-4:2011, Terminations for steel wire ropes — Safety — Part 4: Metal and resin socketing
EN 13411-6:2004+A1:2008, Terminations for steel wire ropes — Safety — Part 6: Asymmetric wedge
socket
EN 13411-7:2006+A1:2008, Terminations for steel wire ropes — Safety — Part 7: Symmetric wedge socket
1)
EN 60034-5:2001 , Rotating electrical machines — Part 5: Degrees of protection provided by the integral
design of rotating electrical machines (IP code) — Classification (IEC 60034-5:2000)
_________________
1) As impacted by EN 60034-5:2001/A1:2007.
EN 60079-0:2018, Explosive atmospheres — Part 0: Equipment — General requirements (IEC 60079-
0:2011)
EN 60079-14:2014, Explosive atmospheres — Part 14: Electrical installations design, selection and erection
(IEC 60079-14:2013)
2)
EN 60529:1991 , Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
__________________
2) As impacted by EN 60529:1991/A1:2000 and EN 60529:1991/A2:2013.
EN 61000-6-2:2019, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards — Immunity for
industrial environments (IEC 61000-6-2)
3)
EN 61000-6-3:2007 , Electromagnetic compatibility (EMC) — Part 6-3: Generic standards — Emission
standard for residential, commercial and light-industrial environments (IEC 61000-6-3:2006)
__________________
3) As impacted by EN 61000-6-3:2007/A1:2011.
EN 61000-6-4:2014, Electromagnetic compatibility (EMC) — Part 6-4: Generic standards — Emission
standard for industrial environments (IEC 61000-6-4)
EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their
components (ISO 4414)
EN ISO 4871:2009, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871)
EN ISO 11688-1:2009, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688-1)
EN ISO 12100:2010, Safety of machinery — General principles for design - Risk assessment and risk
reduction (ISO 12100)
EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of human
responses to contact wit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.