prEN ISO 17779

Brazing - Specification and qualification of brazing procedures for metallic materials (ISO 17779:2021)

This document specifies requirements for the specification and qualification of brazing procedures for brazing of metallic materials.
This document specifies requirements for brazing of the test piece, testing of the test specimen, essential variables and their range of qualification, acceptance criteria, brazing procedure qualification record (BPQR) and brazing procedure specification (BPS).
This document gives general provisions on quality requirements for brazing (see Annex A).
This document does not cover testing of residual stresses, corrosion resistance and impact properties.
This document applies to the following brazing processes according to ISO 857-2 and ISO 4063:2009 with local and global heating:
—    911 Infrared brazing;
—    912 Flame brazing, torch brazing;
—    913 Laser beam brazing;
—    914 Electron beam brazing;
—    916 Induction brazing;
—    918 Resistance brazing;
—    919 Diffusion brazing;
—    921 Furnace brazing;
—    922 Vacuum brazing;
—    923 Dip-bath brazing;
—    924 Salt-bath brazing;
—    925 Flux bath brazing;
—    926 Immersion brazing;
—    972 Arc weld brazing.
The principles of this document can be applied to other brazing processes and brazing of materials not listed.

Hartlöten - Spezifizierung und Qualifizierung von Hartlöt-Prozessen für metallische Werkstoffe (ISO 17779:2021)

Brasage fort - Descriptif et qualification d'un mode opératoire de brassage fort pour les matériaux métalliques (ISO 17779:2021)

Le présent document spécifie les exigences relatives à la spécification et à la qualification des modes opératoires de brasage fort pour les matériaux métalliques.
Le présent document spécifie les exigences pour le brasage fort de l’assemblage de qualification, les essais de l’éprouvette, les variables essentielles et leur domaine de validité, les critères d’acceptation, le procès-verbal de qualification du mode opératoire de brasage fort (PV-QMOB) et le descriptif de mode opératoire de brasage fort (DMOB).
Le présent document donne des dispositions générales sur les exigences de qualité pour le brasage fort (voir Annexe A).
Le présent document ne traite pas des essais portant sur les contraintes résiduelles, la résistance à la corrosion et la résistance à la flexion par choc.
Le présent document s’applique aux procédés de brasage fort suivants, conformes à l’ISO 857-2 et à l’ISO 4063:2009, avec chauffage local et global:
—    911 Brasage fort par infrarouge;
—    912 Brasage fort à la flamme, brasage fort au chalumeau;
—    913 Brasage fort par faisceau laser;
—    914 Brasage fort par faisceau électronique;
—    916 Brasage fort par induction;
—    918 Brasage fort par résistance;
—    919 Brasage fort par diffusion;
—    921 Brasage fort au four;
—    922 Brasage fort sous vide;
—    923 Brasage fort au trempé;
—    924 Brasage fort au bain de sel;
—    925 Brasage fort en bain de flux;
—    926 Brasage fort par immersion;
—    972 Soudobrasage à l’arc.
Les principes du présent document peuvent s'appliquer à d'autres procédés de brasage fort et au brasage de matériaux qui ne figurent pas dans la liste.
Le présent document ne s’applique pas au brasage fort pour les applications aérospatiales couvertes par l’ISO 11745.

Trdo spajkanje - Popis in kvalifikacija postopkov trdega spajkanja kovinskih materialov (ISO 17779:2021)

General Information

• Status: Not Published
• Publication Date: 26-Feb-2023
• ICS: 25.160.50 - Brazing and soldering
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/SC 4 - Quality management in the field of welding
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Start Date: 25-Dec-2022
• Due Date: 23-Aug-2024
• Completion Date: 25-Dec-2022
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/601 - COMMISSION IMPLEMENTING DECISION of 1.3.2024 on a standardisation request to the European Committee for Standardization and the European Committee for Electrotechnical Standardization as regards pressure equipment and assemblies in support of Directive 2014/68/EU of the European Parliament and of the Council
• Ref Project: oSIST prEN ISO 17779:2022 - Brazing - Specification and qualification of brazing procedures for metallic materials (ISO 17779:2021)

Relations

• Revises: EN 13134:2000 - Brazing - Procedure approval
• Effective Date: 09-Nov-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2022
Trdo spajkanje - Popis in kvalifikacija postopkov trdega spajkanja kovinskih
materialov (ISO 17779:2021)
Brazing - Specification and qualification of brazing procedures for metallic materials (ISO
17779:2021)
Brasage fort - Descriptif et qualification d'un mode opératoire de brassage fort pour les
matériaux métalliques (ISO 17779:2021)
Ta slovenski standard je istoveten z: prEN ISO 17779
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 17779
First edition
2021-12
Brazing — Specification and
qualification of brazing procedures for
metallic materials
Brasage fort — Descriptif et qualification d'un mode opératoire de
brassage fort pour les matériaux métalliques
Reference number
ISO 17779:2021(E)
ISO 17779:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 17779:2021(E)
Contents  Page
Foreword .iv
Introduction .v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  Preliminary brazing procedure specification (pBPS) . 3
5  Brazing procedure test . 3
6  Test piece . 3
6.1 General . 3
6.2 Shape and dimensions of test pieces . 3
6.3 Brazing of test pieces . 4
7  Examination and testing . 4
7.1 Extent of testing . 4
7.2 Test specimens. 5
7.3 Non-destructive testing . 5
7.4 Destructive testing . 5
7.4.1 General . 5
7.4.2 Bend testing . 5
7.4.3 Peel testing . 5
7.4.4 Shear testing . 5
7.4.5 Transverse tensile testing . 6
7.5 Acceptance levels . 6
7.6 Re-testing . 6
8  Essential variables and range of qualification . 6
8.1 General . 6
8.2 Brazing process. 6
8.3 Product type . 6
8.4 Type of joint . 7
8.5 Branch connection . 7
8.6 Parent material group(s) . 7
8.7 Filler metals, flux and brazing filler application . 8
8.8 Dimensions . 8
8.9 Filler metal flow direction . 8
8.10 Post braze heat treatment . 9
8.11 Related to the manufacturer . 9
9  Brazing procedure qualification record (BPQR) . 9
10  Brazing procedure specification (BPS) . 9
Annex A (informative) Quality requirements for brazing .11
Annex B (informative) Brazing procedure specification (BPS) .12
Annex C (informative) Examples of test pieces .13
Annex D (informative) Brazing procedure qualification record (BPQR) .15
Annex E (normative) Material grouping system .16
iii
ISO 17779:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes
Subcommittee SC 11, Qualification requirements for welding and allied processes personnel.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
ISO 17779:2021(E)
Introduction
The purpose of this document is to provide a general set of rules for brazing procedure qualification
independent of product or application.
All new brazing procedure tests are to be carried out in accordance with this document from the date of
its issue. However, this document does not invalidate previous brazing procedure tests made to former
standards or specifications.
Where additional tests need to be carried out to make the qualification technically equivalent, it is only
necessary to perform the additional tests on a test piece which should be made in accordance with this
document.
v
INTERNATIONAL STANDARD ISO 17779:2021(E)
Brazing — Specification and qualification of brazing
procedures for metallic materials
1  Scope
This document specifies requirements for the specification and qualification of brazing procedures for
brazing of metallic materials.
This document specifies requirements for brazing of the test piece, testing of the test specimen,
essential variables and their range of qualification, acceptance criteria, brazing procedure qualification
record (BPQR) and brazing procedure specification (BPS).
This document gives general provisions on quality requirements for brazing (see Annex A).
This document does not cover testing of residual stresses, corrosion resistance and impact properties.
This document applies to the following brazing processes according to ISO 857-2 and ISO 4063:2009
with local and global heating:
— 911 Infrared brazing;
— 912 Flame brazing, torch brazing;
— 913 Laser beam brazing;
— 914 Electron beam brazing;
— 916 Induction brazing;
— 918 Resistance brazing;
— 919 Diffusion brazing;
— 921 Furnace brazing;
— 922 Vacuum brazing;
— 923 Dip-bath brazing;
— 924 Salt-bath brazing;
— 925 Flux bath brazing;
— 926 Immersion brazing;
— 972 Arc weld brazing.
The principles of this document can be applied to other brazi
...