SLOVENSKI STANDARD
SIST EN 12312-1:2002/kprA1:2008
01-november-2008
Podporna oprema na tleh za letalski promet - Posebne zahteve - 1. del: Stopnice za
potnike
Aircraft ground support equipment - Specific requirements - Part 1: Passenger stairs
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 1: Fluggasttreppen
Matériel au sol pour aéronefs - Exigences particulières - Partie 1: Escaliers passagers
Ta slovenski standard je istoveten z: EN 12312-1:2001/prA1
ICS:
49.100 Oprema za servis in Ground service and
vzdrževanje na tleh maintenance equipment
SIST EN 12312-1:2002/kprA1:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12312-1:2002/kprA1:2008

---------------------- Page: 2 ----------------------

SIST EN 12312-1:2002/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 12312-1:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 49.100

English Version
Aircraft ground support equipment - Specific requirements - Part
1: Passenger stairs
Matériel au sol pour aéronefs - Exigences particulières - Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 1:
Partie 1: Escaliers passagers Fluggasttreppen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 274.
This draft amendment A1, if approved, will modify the European Standard EN 12312-1:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12312-1:2001/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12312-1:2002/kprA1:2008
EN 12312-1:2001/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Introduction .4
3 Modification to Clause 1 .4
4 Modification to Clause 2 .4
5 Modification to Clause 3 .4
6 Modification to Clause 4 .5
7 Modification to Clause 5 .5
8 Modification to Clause 7 .5
9 Modification to Annex B.5
10 Modification to Annex ZA .6
11 Addition of Annex ZB .7

2

---------------------- Page: 4 ----------------------

SIST EN 12312-1:2002/kprA1:2008
EN 12312-1:2001/prA1:2008 (E)
Foreword
This document (EN 12312-1:2001/prA1:2008) has been pre
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN

EN 1915-1:2023(Main)

Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements

SIST EN 1915-1:2023

This document applies to GSE when used in civil air transport as intended by the manufacturer and contains safety requirements relating to the equipment in general.
This document specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of GSE when used as intended including any reasonably foreseeable misuse by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This part of EN 1915 is intended to be used in conjunction with EN 1915-2:2001+A1:2009, EN 1915-3:2004+A1:2009 (for self-propelled GSE) and EN 1915-4:2004+A1:2009, and with the relevant part of EN 12312 to give the requirements for the types of GSE within the scope of EN 12312.
When EN 12312 does not contain a relevant part for a GSE, EN 1915 (all parts) gives general requirements that may apply, although additional machine specific requirements, to be determined by the manufacturer, are likely to be required.
This part of EN 1915 does not apply to automotive parts approved for public vehicles in the EU and EFTA, when used on GSE for the purpose for which they are designed.
This part of EN 1915 does not establish additional requirements for the following:
a)   operation elsewhere than in an airport environment;
b)   operation in severe conditions, e.g. ambient temperature below -20 °C or over 50 °C, tropical or saturated salty atmospheric environment, strong magnetic or radiation field;
c)   operation subject to special rules, e.g. potentially explosive atmosphere except as regards operation in the vicinity of an aircraft fuel tank during fuelling operation;
d)   hazards caused by power supply other than from electrical networks;
e)   hazards occurring during construction, transportation, decommissioning and disassembly of the GSE;
f)   hazards caused by wind velocity in excess of the figures given in this document;
g)   direct contact with food stuffs;
h)   earthquake, flood, landslide, lightning and more generally any exceptional natural event;
i)   electromagnetic compatibility (EMC);
j)   hazards caused by noise and vibration, see EN 1915-3:2004+A1:2009 and EN 1915-4:2004+A1:2009.
While this standard gives some basic requirements for wireless remote controls, additional requirements will be necessary.
This part of EN 1915 is not applicable to GSE which are manufactured before the date of publication by CEN of this document.

Standard
68 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 12312-15:2020+A1:2022(Main)

Aircraft ground support equipment - Specific requirements - Part 15: Baggage and equipment tractors

SIST EN 12312-15:2020+A1:2023

This document specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of baggage and equipment tractors when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This document applies to self-propelled baggage and equipment tractors with driver accommodation.
This document does not apply to pedestrian controlled equipment.
This document deals with vibrations which are considered as significant. Vibration measurements are dealt with in EN 1915-3.
No extra requirements on noise are provided other than those given in EN 1915-4.
NOTE EN 1915-4 provides the general GSE noise requirements.
This part of EN 12312 is not applicable to baggage and equipment tractors manufactured before the date of its publication.
This part of EN 12312 when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 provides the requirements for baggage and equipment tractors.

Standard
32 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 12312-5:2021(Main)

Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment

SIST EN 12312-5:2021

This document specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of AFE when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some performance requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines, airports and fuelling companies.
This document applies to all types of aircraft fuelling equipment:
a)   aircraft refuellers,
b)   hydrant dispensers,
c)   defuellers,
d)   hydrant pit servicing vehicles,
e)   pit cleaner vehicles, and
f)   stationary dispensing units
intended to service aircraft with aviation fuels and to be operated on airfields, heliports and other aircraft refuelling related areas such as maintenance bases.
This document does not apply to:
g)   AFE whose only power source for aircraft refuelling is directly applied manual effort,
h)   hydrant systems, tank farms, pipework and underground tanks,
i)   specific hazards due to the operation of the AFE in a potentially explosive atmosphere, and
j)   built-in fire extinguisher systems.
No extra requirements on noise and vibration are provided other than those in EN 1915-3:2004+A1:2009 and EN 1915- 4:2004+A1:2009.
NOTE    EN 1915-3:2004+A1:2009 and EN 1915-4:2004+A1:2009 provide the general GSE vibration and noise requirements.
This document does not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron.
This document is not applicable to AFE which are manufactured before the date of publication of this document by CEN.
This part of the EN 12312 series when used in conjunction with EN 1915-1:2013, EN 1915-2:2001+A1:2009, EN 1915-3:2004+A1:2009 (for vehicles) and EN 1915-4:2004+A1:2009 provides the requirements for AFE.

Standard
52 pages
English language
sale 10% off
e-Library read for
1 day

02-Mar-2021
29-Sep-2021
49.100
2006/42/EC
M/396
CEN/TC 274

CEN

EN 12312-7:2020(Main)

Aircraft ground support equipment - Specific requirements - Part 7: Aircraft movement equipment

SIST EN 12312-7:2020

This document specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of aircraft movement equipment when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some performance requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This document applies to:
-   aircraft tractors with driver accommodation,
-   remote controlled aircraft movement equipment, and
-   attachment devices
used for all operations utilizing aircraft movement equipment, e.g.:
-   push back, and
-   maintenance towing.
This document does not apply to:
-   ground power installations on aircraft tractors,
-   fixed ramp integrated systems,
-   special towing equipment (e.g. for recovery),
-   dispatch towing tractors, or
-   tractors with a standing driver.
This document deals with vibrations and noise which are considered as significant hazards. Vibration measurements are dealt with in EN 1915 3:2004+A1:2009. Noise measurements and reduction are dealt with in EN 1915 4:2004+A1:2009.
This document does not deal with hazards in respect to a standard automotive chassis or from hazards arising from potential interaction with other vehicles on the apron.
This part of EN 12312 is not applicable to aircraft movement equipment manufactured before the date of its publication.
This part of EN 12312 is intended to be used in conjunction with EN 1915 1:2013, EN 1915 2:2001+A1:2009, EN 1915 3:2004+A1:2009 (for vehicles) and EN 1915 4:2004+A1:2009.
This part of EN 12312 when used in conjunction with EN 1915 1:2013, EN 1915 2:2001+A1:2009, EN 1915 3:2004+A1:2009 and EN 1915 4:2004+A1:2009 provides the requirements for aircraft movement equipment.

Standard
29 pages
English language
sale 10% off
e-Library read for
1 day

13-Oct-2020
29-Apr-2021
49.100
2006/42/EC
M/396
CEN/TC 274

CEN

EN 12312-3:2017+A1:2020(Main)

Aircraft ground support equipment - Specific requirements - Part 3: Conveyor belt vehicles

SIST EN 12312-3:2017+A1:2020

This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of conveyor belt vehicles when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This European Standard applies to
a)   self-propelled conveyor belt vehicles with or without driver's accommodation,
b)   self-propelled conveyor belt vehicles equipped with a van body,
c)   towed conveyor belt vehicles,
intended to be used for manual loading/unloading of aircraft.
This European Standard does not apply to any extensions or appurtenances of conveyor belt vehicles entering the aircraft cargo compartment in order to facilitate loading and unloading therein ("Aircraft Bulk Loading Systems", ABLS).
This European Standard does not apply to pneumatic systems and to cable-less remote controls.
This part of EN 12312 is not applicable to conveyor belt vehicles which were manufactured before the date of publication of this European Standard by CEN.
This part of EN 12312 when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 provides the requirements for conveyor belt vehicles.

Standard
30 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN ISO 11532:2020(Main)

Aircraft ground equipment - Graphical symbols (ISO 11532:2018)

SIST EN ISO 11532:2020

ISO 11532:2018 establishes common graphical symbols for use on all types of aircraft ground support equipment.
They have been compiled for the benefit of those who deal with such equipment, such as airlines, airport handling agencies, airport authorities, manufacturers, etc., in order to facilitate fast and accurate identification of controls, indicators and decals of powered and unpowered equipment.
The presentation of this document is based on the recommendations of ISO/TC 145, Graphical symbols.
ISO 11532:2018 is also intended to promote standardization of terms for controls, indicators, etc. for aircraft ground support equipment and alleviate language problems.
These graphical symbols are intended to be placed on all new equipment and retrofitted on all existing equipment as far as possible.
NOTE This document is intended to be read with the documents listed in the bibliography.

Standard
44 pages
English language
sale 10% off
e-Library read for
1 day

09-Jun-2020
30-Dec-2020
01.080.20
49.100
CEN/TC 274

CEN

EN 12312-8:2018(Main)

Aircraft ground support equipment - Specific requirements - Part 8: Maintenance or service stairs and platforms

SIST EN 12312-8:2018

1.1   General
This document specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of maintenance or service stairs and platforms when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
These machines are designed to be used as aircraft ground support equipment with the intended use to serve aircraft in outdoor conditions on the apron. They can also be used indoors at hangars. The use of such equipment for operations not in conjunction with aircraft is not defined as intended use therein. Due to the good operational conditions on the apron, deviations from some clauses of EN 280 were deemed acceptable.
This European Standard applies to:
a)   self-propelled fixed or adjustable maintenance or service stairs and elevating platforms;
b)   towable maintenance or service stairs and platforms equipped with powered means, e.g. for height adjustment, stabilizers;
designed for aircraft maintenance or service purposes including access to the aircraft.
NOTE 1   Powered will be also understood as manual effort stored in springs or hydraulic accumulators, etc., the dangerous action of which can be produced or can continue after the manual effort has ceased or directly applied manual effort for lifting or lowering loads.
NOTE 2   Those clauses of this standard that can apply can also be used as a guideline for the design of towable maintenance or service stairs and platforms without powered means.
This European Standard does not apply to:
c)   maintenance docks either fixed to the ground or moveable only for docking procedure;
d)   ground support equipment specifically intended, built and equipped with a fluid system for aircraft de-icing and anti-icing (see EN 12312 6);
NOTE 3   This does not prevent aircraft de-icers meeting the requirements of EN 12312 6 from being used as a means of access for aircraft maintenance, e.g. windshield cleaning, etc.
e)   mobile elevating work platforms (MEWP) used at the airports for purposes other than aircraft maintenance, e.g. buildings and facilities (see EN 280).
No extra requirements on noise and vibration are provided other than those given in EN 1915 3 and EN 1915 4.
NOTE 4   EN 1915 3 and EN 1915 4 provide the general GSE vibration and noise requirements.
This European Standard does not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron.
This part of EN 12312 is not applicable to maintenance or service stairs and platforms which are manufactured before the date of publication of this standard by CEN.
This part of EN 12312 when used in conjunction with EN 1915 1, EN 1915 2, EN 1915 3 and EN 1915 4 provides the requirements for maintenance or service stairs and platforms.
1.2   Classification
For the purposes of this document, mobile elevating work platforms (MEWPs) used for aircraft maintenance access are divided into two main groups A and B. In addition, group C is considered as described in c) hereafter:
a)   Group A: MEWPs where the vertical projection of the centre of the platform area is always inside the tipping lines.
NOTE 1   See 5.2 hereafter for the specific requirements applying to Group A MEWPs.
b)   Group B: MEWPs where the vertical projection of the centre of the platform area may be outside the tipping lines.
NOTE 2   See 5.3 hereafter for the specific requirements applying to Group B MEWPs.
c)   Group C consists of maintenance or service access stairs, where persons are not elevated by the machine but climb a flight of steps.
(...)

Standard
28 pages
English language
sale 10% off
e-Library read for
1 day

14-Aug-2018
27-Feb-2019
49.100
2006/42/EC
M/079
M/396
CEN/TC 274

CEN

EN 12312-12:2017(Main)

Aircraft ground support equipment - Specific requirements - Part 12: Potable water service equipment

SIST EN 12312-12:2017

This European Standard specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of potable water service equipment when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This European Standard applies to:
a)   self-propelled potable water vehicles;
b)   towable potable water vehicles;
c)   moveable parts of ramp integrated systems,
designed for servicing aircraft and intended to be used under the conditions given in EN 1915-1:2013, 1.
No extra requirements on noise and vibration are provided other than those in EN 1915-3 and EN 1915-4.
NOTE   EN 1915-3 and EN 1915-4 provide the general GSE vibration and noise requirements.
This part of EN 12312 is not applicable to potable water service equipment which is manufactured before the date of publication of this standard by CEN.
This part of EN 12312, when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4, provides the requirements for potable water service equipment.

Standard
16 pages
English language
sale 10% off
e-Library read for
1 day

09-May-2017
29-Nov-2017
49.100
2006/42/EC
M/396
CEN/TC 274

CEN

EN 12312-13:2017(Main)

Aircraft ground support equipment - Specific requirements - Part 13: Lavatory service equipment

SIST EN 12312-13:2017

This European Standard specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of lavatory service equipment when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This European Standard applies to:
a)   self-propelled lavatory vehicles;
b)   towable lavatory vehicles;
c)   moveable parts of ramp integrated systems,
designed for servicing aircraft and intended to be used under the conditions given in EN 1915-1:2013, Clause 1.
No extra requirements on noise and vibration are provided other than those in EN 1915-3 and EN 1915-4.
NOTE   EN 1915-3 and EN 1915-4 provide the general GSE vibration and noise requirements.
This part of EN 12312 is not applicable to lavatory service equipment which is manufactured before the date of publication of this standard by CEN.
This part of EN 12312, when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4, provides the requirements for lavatory service equipment.

Standard
18 pages
English language
sale 10% off
e-Library read for
1 day

09-May-2017
29-Nov-2017
49.100
2006/42/EC
M/396
CEN/TC 274

CEN

EN 12312-6:2017(Main)

Aircraft ground support equipment - Specific requirements - Part 6: Deicers and de-icing/anti-icing equipment

SIST EN 12312-6:2017

This European Standard specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of deicers and equipment designed exclusively for deicing and washing of aircraft with deicing/antiicing/washing liquids when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
NOTE 1   Safety of aircraft in connection with deicing/antiicing operations is not dealt with in this European Standard. Any, even minor, aircraft deicing or antiicing operation directly affects flight safety on take-off. Prevention of aeronautical accidents resulting from in-flight icing principally concerns the fluids and methods used, but it may in certain cases also concern deicing or antiicing equipment design or operation. These aeronautical aspects are controlled by the applicable Civil Aviation regulations ICAO 9640-AN/940, Manual of aircraft ground de-icing/anti-icing operations and EASA EU-OPS Subpart D 1.345 and its Acceptable Means of Compliance (AMC) and covered in ISO 11076:2012 (AEA Recommendations). They are not covered in this European Standard.
This European Standard applies to:
a)   self-propelled deicers with fixed or mobile platform or hinged boom;
b)   towable deicers with fixed or mobile platform or hinged boom;
c)   stationary deicing/antiicing equipment (e.g. fixed boom, gantry or tower cranes equipped with aircraft deicing/antiicing fluid systems).
This European Standard does not apply to:
d)   fixed installations, such as separate storage tanks or heating and filling stations, which are not an integrated part of the stationary deicing equipment;
e)   hydraulic control systems;
f)   pneumatic systems;
g)   flow generating systems as such.
No extra requirements on noise and vibration are provided other than those in EN 1915-3 and EN 1915-4.
NOTE 2   EN 1915-3 and EN 1915-4 provide the general GSE vibration and noise requirements.
This European Standard is not dealing with hazards in respect to a standard automotive chassis and the traffic on the apron.
This part of EN 12312 is not applicable to deicers and deicing/antiicing equipment which are manufactured before the date of publication of this standard by CEN.
This part of EN 12312 when used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 provides the requirements for deicers and deicing/antiicing equipment.

Standard
42 pages
English language
sale 10% off
e-Library read for
1 day

21-Mar-2017
29-Sep-2017
49.100
2006/42/EC
M/396
CEN/TC 274