iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1092-3:2003/AC:2007

(Corrigendum)

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flanges

Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flanges

2010-11-05 EMA: WI allocated to WG 4 following resolution 291 taken on 2010-10-21.
TC - Modification in Table 6, dimensions of PN 10 flanges, DN 40: change of pitch circle diameter according to resolution CEN/TC 74 260/2006
NOTE   The first Corrigendum EN 1092:2003/AC:2004, WI 00074C01 has been published as full text with the following sentence in the Foreword: "Due to the incorrect hatching, all figures were replaced.". Merging the full text plus instruction of the first Corrigendum with the instruction of the second Corrigendum was not possible. That is why it has been decided to merge only the instructions of the first and second Corrigenda into one new Corrigendum. Jens, 2007-07-23

Flansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke und Zubehörteile, nach PN bezeichnet - Teil 3: Flansche aus Kupferlegierungen

Brides et leurs assemblages - Brides circulaires pour tubes, appareils de robinetterie, raccords et accessoires, désignées PN - Partie 3: Brides en alliages de cuivre

Prirobnice in prirobnični spoji - Okrogle prirobnice za cevi, ventile, fitinge in pribor z oznako PN - 3. del: Prirobnice iz bakrovih zlitin - Popravek AC

General Information

Status
Published
Publication Date
28-Aug-2007
ICS
23.040.60 - Flanges, couplings and joints
Technical Committee
CEN/TC 74 - Flanges and their joints
Drafting Committee
CEN/TC 74 - Flanges and their joints
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
29-Aug-2007
Completion Date
29-Aug-2007
Directive
2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 1092-3:2004/AC:2007 - Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flanges

Relations

Replaces
EN 1092-3:2003/AC:2004 - Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flanges
Effective Date
15-Aug-2009
Corrects
EN 1092-3:2003 - Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flanges
Effective Date
22-Dec-2008

Buy Standard

EN 1092-3:2004/AC:2007EN 1092-3:2004/AC:2007
PreviousNext
Corrigendum
EN 1092-3:2004/AC:2007
English, French and German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 3: Copper alloy flangesBrides et leurs assemblages - Brides circulaires pour tubes, appareils de robinetterie, raccords et accessoires, désignées PN - Partie 3: Brides en alliages de cuivreFlansche und ihre Verbindungen - Runde Flansche für Rohre, Armaturen, Formstücke und Zubehörteile, nach PN bezeichnet - Teil 3: Flansche aus KupferlegierungenTa slovenski standard je istoveten z:EN 1092-3:2003/AC:2007SIST EN 1092-3:2004/AC:2007en,fr,de23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:SLOVENSKI
STANDARDSIST EN 1092-3:2004/AC:200701-december-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1092-3:2003/ACAugust 2007Août 2007August 2007ICS 23.040.60English versionVersion FrançaiseDeutsche FassungFlanges and their joints - Circular flanges for pipes, valves, fittings andaccessories, PN designated - Part 3: Copper alloy flangesBrides et leurs assemblages - Bridescirculaires pour tubes, appareils derobinetterie, raccords et accessoires,désignées PN - Partie 3: Brides en alliagesde cuivreFlansche und ihre Verbindungen - RundeFlansche für Rohre, Armaturen,Formstücke und Zubehörteile, nach PNbezeichnet - Teil 3: Flansche ausKupferlegierungenThis corrigendum becomes effective on 29 August 2007 for incorporation in the three officiallanguage versions of the EN.Ce corrigendum prendra effet le 29 août 2007 pour incorporation dans
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1591-1:2024(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation
SIST EN 1591-1:2024

This document defines a calculation method for bolted, gasketed, circular flange joints. Its purpose is to ensure structural integrity and control of leak tightness. It uses gasket parameters based on definitions and test methods specified in EN 13555:2014.
The calculation method is not applicable to joints with a metallic contact out of the sealing face or to joints whose rigidity varies appreciably across gasket width. For gaskets in incompressible materials, which permit large deformations, the results given by the calculation method can be excessively conservative (i.e. required bolting load too high, allowable pressure of the fluid too low, required flange thickness too large, etc.).

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1092-2:2023(Main)
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
SIST EN 1092-2:2024

This document specifies requirements for circular flanges made from ductile, grey and malleable cast iron for DN 10 to DN 4000 and PN 2,5 to PN 100. See 4.1 and 4.2 for information regarding allowed DN and PN.
This document specifies the types of flanges and their facings, dimension and tolerances, bolt sizes, surface finish of jointing faces, marking, testing, quality assurance and materials together with associated pressure/temperature (p/T) ratings.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021/AC:2022(Corrigendum)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021/AC:2022

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021(Main)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13555:2021(Main)
Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
SIST EN 13555:2021

This document specifies the gasket parameters required by EN 1591-1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of other shapes and dimensions.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14772:2021(Main)
Flanges and their joints - Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560
SIST EN 14772:2021

This document specifies the quality assurance procedures that are applicable to ensure that delivered gaskets comply with the relevant product standards. This document sets down procedures by which a user can have confidence that the salient features of each batch of gaskets or gasket materials delivered to them will be constant.
The gasket types covered by this document are those that are within the scope of the EN 1514 series and EN 12560 series and are simultaneously within the scope of the EN 1591 series. An exception is those gaskets intended solely for domestic fluids (like water, waste water ...) which are based on rubber with or without reinforcement like fillers and/or inserts.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 1591-2:2020(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 2: Gasket parameters
SIST-TP CEN/TR 1591-2:2020

This document details generic gasket parameters for use in EN 1591-1 during preliminary calculations during which the type of gasket to be used in an application is to be decided. Once the gasket type has been decided the parameters for gaskets of that type from the different potential commercial suppliers should be used in further calculations as within a gasket type there will be differences depending upon the supplier.
WARNING - For the final calculations using the method given in EN 1591-1 the reader is directed to obtain gasket parameters for the selected generic type of gasket from the intended gasket manufacturer. This is because the data for a generic gasket type will vary between manufacturers. This variation can be seen in the tables of data which are embodied in this document.

  • Technical report
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1092-1:2018(Main)
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges
SIST EN 1092-1:2018

This European Standard for a single series of flanges specifies requirements for circular steel flanges in PN designations PN 2,5 to PN 400 and nominal sizes from DN 10 to DN 4000.
This European Standard specifies the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange jointing face surface finish, marking, materials, pressure/ temperature ratings and approximate flange masses.
For the purpose of this European Standard, "flanges" include also lapped ends and collars.
This European Standard applies to flanges manufactured in accordance with the methods described in Table 1.
Non-gasketed pipe joints are outside the scope of this European Standard.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1591-4:2013(Main)
Flanges and their joints - Part 4: Qualification of personnel competency in the assembly of the bolted connections of critical service pressurized systems
SIST EN 1591-4:2013

This European Standard is applicable to the bolting technicians, and their supervisors, the responsible engineers, who disassemble, assemble and tighten the bolted connections of whatever shape of critical service pressurised systems. A failure of a connection in such a system would endanger personnel, plant or the environment. A route for achieving competency in the skills required to safely and successfully disassemble, assemble and tighten pressurised bolted joints of any shape to a design bolt load using documented work instructions is given in this document. The aim is the establishment of a joint capable of maintaining a leak-free status throughout its’ service life.
This European Standard provides a modular training syllabus and an assessment process that can be used to determine the competency of personnel who disassemble, assemble and tighten bolted connections, whatever their shape, fitted to pressurised equipment containing a medium at any combination of temperature and pressure.
Bolting technicians have to assemble bolted connections of different levels of complexity. For this reason, training matrices dealing with bolted connections of various levels of complexity and for different types of pressurised bolted connections are given in this document. The modular structure created allows a bolting technician, once competency in the foundation level has been achieved, to obtain competency in higher levels as required.
Certification to this European Standard provides an attestation of general competency in accordance with the stated syllabi and assessments.
Certification to this European Standard does not represent an authorisation to operate, since this remains the responsibility of the employer, and the certified person may require additional specialised knowledge of employer-specific procedures, processes and equipment.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    18 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 1591-5:2012(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 5: Calculation method for full face gasketed joints
SIST-TP CEN/TR 1591-5:2012

This Technical Report gives guidance for the calculation of full face gasketed joints on the basis of the calculation method given in EN 1591-1.

  • Technical report
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day