prEN ISO/ASTM 52929
(Main)Additive manufacturing of metals - Powder bed fusion - Presentation of material properties in material data sheets (ISO/ASTM DIS 52929:2023)
Additive manufacturing of metals - Powder bed fusion - Presentation of material properties in material data sheets (ISO/ASTM DIS 52929:2023)
This document specifies basic content and relevant parameters to be reported in material data sheets. Individual additions and extensions are permissible. This document is intended for manufacturers of PBF-LB/M or PBF-EB/M equipment, powder suppliers, service providers and users of the additively manufactured components.
Additive Fertigung von Metallen - Pulverbettbasiertes Schmelzen - Darstellung von Werkstoffkennwerten in Materialdatenblättern (ISO/ASTM DIS 52929:2023)
Fabrication additive de métaux - Fusion sur lit de poudre - Présentation des propriétés des matériaux dans les fiches de données de matériaux (ISO/ASTM DIS 52929:2023)
Aditivna proizvodnja kovinskih izdelkov - Spajanje prahu v postelji (PBF) - Predstavitev lastnosti materialov v podatkovnih listih (ISO/ASTM DIS 52929:2023)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2023
Aditivna proizvodnja kovinskih izdelkov - Spajanje prahu v postelji (PBF) -
Predstavitev lastnosti materialov v podatkovnih listih (ISO/ASTM DIS 52929:2023)
Additive manufacturing of metals - Powder bed fusion - Presentation of material
properties in material data sheets (ISO/ASTM DIS 52929:2023)
Additive Fertigung von Metallen - Pulverbettbasiertes Schmelzen - Darstellung von
Werkstoffkennwerten in Materialdatenblättern (ISO/ASTM DIS 52929:2023)
Fabrication additive de métaux - Fusion sur lit de poudre - Présentation des propriétés
des matériaux dans les fiches de données de matériaux (ISO/ASTM DIS 52929:2023)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52929
ICS:
25.030 3D-tiskanje Additive manufacturing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52929
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-10-11 2024-01-03
Additive manufacturing of metals — Powder bed fusion —
Presentation of material properties in material data sheets
ICS: 25.030
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/ASTM DIS 52929:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2023
ISO/ASTM DIS 52929:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52929
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
Additive manufacturing of metals — Powder bed fusion —
Presentation of material properties in material data sheets
ICS: 25.030
This document is circulated as received from the committee secretariat.
© ISO/ASTM International 2023 THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
NOT BE REFERRED TO AS AN INTERNATIONAL
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below STANDARD UNTIL PUBLISHED AS SUCH.
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
ISO copyright office ASTM International
TECHNOLOGICAL, COMMERCIAL AND
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
USER PURPOSES, DRAFT INTERNATIONAL
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
Phone: +41 22 749 01 11 Phone: +610 832 9634
POTENTIAL TO BECOME STANDARDS TO
Fax: +610 832 9635
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org Email: khooper@astm.org
NATIONAL REGULATIONS.
Website: www.iso.org Website: www.astm.org ISO/ASTM DIS 52929:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO/ASTM International 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2023
ISO/ASTM DIS 52929:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviations . 1
5 Material properties to be displayed . .1
6 Optional material properties to be displayed . 2
7 Boundary conditions for the determination of material properties .3
7.1 General . 3
7.2 Applied PBF machine(s) . 3
7.3 Applied feedstock . 3
7.4 Applied process parameters . 3
7.5 Applied shielding gas . 4
7.6 Applied powder spreading device . 4
7.7 Post-processing applied . 4
8 Specimen orientation and measuring directions . 5
8.1 General . 5
8.2 Tensile test . 5
8.3 Notched bar impact test . 5
8.4 Hardness . 6
8.5 Density . 6
9 Number of specimens and build jobs .6
10 Reporting of characteristic values .7
Annex A (informative) Example of a material data sheet . 9
Bibliography .11
iii
© ISO/ASTM International 2023 – All rights reserved
ISO/ASTM DIS 52929:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 261, Additive manufacturing, in cooperation with
ASTM Committee F42, Additive Manufacturing Technologies, on the basis of a partnership agreement
between ISO and ASTM International with the aim to create a common set of ISO/ASTM standards on
Additive Manufacturing.
iv
© ISO/ASTM International 2023 – All rights reserved
ISO/ASTM DIS 52929:2023(E)
Introduction
Equipment manufacturers and service providers publish material properties for additively
manufactured components or specimens produced by powder bed fusion of metals using laser or
electron beams.
Such published material properties are not always comparable, due to missing specifications on how
associated measurements were conducted. For example, the number of specimens tested, the number of
build jobs used, the specimen´s geometry and variations due to orientation are individually determined
and usually not published.
The objective of this document is to specify the minimum requirements for the derivation and reporting
of material properties to support transparency and uniformity of material data sheets.
v
© ISO/ASTM International 2023 – All rights reserved
DRAFT INTERNATIONAL STANDARD ISO/ASTM DIS 52929:2023(E)
Additive manufacturing of metals — Powder bed fusion —
Presentation of material properties in material data sheets
1 Scope
This document specifies minimum content and relevant parameters to be reported in material data
sheets. Individual additions and extensions are permissible. This document is intended for use by
organisations throughout the additive manufacturing supply-chain, e.g., manufacturers of PBF-LB/M
or PBF-EB/M equipment, powder suppliers, service providers and users of the additively manufactured
components.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/ASTM 52900, Additive manufacturing — General principles — Fundamentals and vocabulary
1)
ISO/ASTM 52927 , Additive manufacturing — General principles — Main characteristics and
corresponding test methods
ISO 17295:2023, Additive manufacturing — General principles — Part positioning, coordinates and
orientation
ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/ASTM 52900 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Abbreviations
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.