Abstract

This document is applicable to all water slides installed at open water areas for public use or in swimming pools for public use.
This document specifies general safety requirements for water slides installed at open water areas for public use or in swimming pools for public use and specific requirements for defined types of water slides. These specific safety requirements are also applicable to undefined types as far as possible.
These requirements concern safety and the technical rules for design, calculation and testing.

Status
Published
Publication Date
28-Jul-2026
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
29-Jul-2026
Due Date
28-Sep-2026
Completion Date
29-Jul-2026

Buy Documents

Standard

EN 1069-1:2026

English language (56 pages)
Preview
Preview
e-Library read for
×1 day

EN 1069-1:2026 is a CEN standard for water slides installed in open water areas or swimming pools for public use. It specifies general safety requirements, specific requirements for defined water slide types, and the test methods used to check them. It is written for designers, manufacturers, installers, operators, testers, and others who need to assess whether a water slide is safe to build and use.

What does EN 1069-1:2026 specify?

EN 1069-1:2026 applies to water slides for public use in open water areas and swimming pools. It sets safety requirements and technical rules for design, calculation, and testing, and it also extends type-specific safety provisions to undefined types where that is reasonably possible.

The document is organized into 10 clauses and 4 annexes. Clauses 4 to 10 cover classification, materials and construction, design analysis, safety requirements, additional requirements by type, check and test runs, and designation and marking.

AnnexWhat it covers
Annex ASplashdown areas and their dimensions
Annex BUse of stainless steels for water slides
Annex CDesign loads, accesses, and platforms
Annex DAcceleration and speed measurements

What are the key requirements of EN 1069-1:2026?

EN 1069-1:2026 combines geometry, structural design, user safety, and verification rules. In practice, it tells a designer or operator what type of slide they have, how to size and support it, how to control landing and access risks, and what to prove by test.

Classification and special elements

Clause 4 classifies water slides into Types 1 to 7 and also identifies special elements: bowl, lateral oscillation element, uphill element, and wild river. The classification matters because later safety and dimensional requirements depend on the type, especially for slide width, curvature, maximum speed, and landing arrangements.

Materials and construction

Clause 5 requires materials and finishes to suit the intended use, the environment, and high humidity or corrosive conditions. It also requires materials to avoid promoting bacterial growth and limits certain hazardous substances, which matters when selecting plastics, coatings, or metals for wet public facilities.

For safety-critical building materials, Clause 5 points to inspection documentation, and welders must be qualified according to EN ISO 9606-1. The designer must also specify protection or inspection frequency, because corrosion control is part of the slide’s safety case, not just maintenance.

Design analysis and structural loads

Clause 6 treats water slides as structures and requires a preliminary risk analysis at design stage for every slide. That risk analysis has to consider the user group, the setting, and risks such as ejection, impact, falls, entrapment, interference between users, and hazards in the landing area.

The structural analysis uses Eurocode principles and load combinations for self-weight, water load, user load, snow, wind, temperature, impacts, and stabilization actions. This matters in practice because the slide, supports, accesses, and platforms must be designed not only for use loads but also for the environmental and operational loads that affect safety over time.

Accesses, platforms, and fall protection

Clause 7 gives detailed requirements for access routes, stairs, stepladders, platforms, handrails, barriers, slip resistance, and protection against falling. For example, platforms need barriers, access should prevent unintended entry when the slide is not operating, and the slide start area must be arranged so users are not forced forward by people coming from behind.

These provisions matter because many accidents happen before a rider even reaches the slide proper. The clause also controls surface quality, edges, entrapping openings, and start-section layout so that the user stays contained and does not hit exposed parts.

Slide path, landing, and splashdown

Clause 7 also controls the slide proper, the final part, and the landing area. The sliding path must limit instability, turning, tipping, lateral oscillation, and ejection, and acceleration on the rider has to stay within defined limits.

Landing can be by catch unit, sofa unit, surf landing, or splashdown area, depending on the slide type and speed. This matters because landing is one of the main injury points: the slide must slow the rider safely, leave enough water depth or clearance, and prevent collisions with pool walls, obstacles, or other users.

Water supply and user separation

Clause 7.12 requires the water flow rate to be defined at commissioning and protected against unauthorized interference. For some slide types, the preliminary risk analysis determines whether flow monitoring and an alarm are needed.

Clauses 7.13 and 7.14 require the slide to be arranged so users do not interfere with one another or with non-users. In practice, this means spacing, access control, and clearance zones must be designed into the facility, not left to operating rules alone.

Check, test runs, and marking

Clause 9 requires technical and physical checks, and for Types 3 to 7 and special elements it requires a practical test by at least 3 slide testers under supervision. When accelerations or speeds cannot be calculated with enough certainty, measurements are taken using Annex D or an equivalent method.

Clause 10 requires a designation system and marking on the installed slide. That helps operators identify the slide type and gives users and inspectors a visible reference for the installed equipment.

What terms does EN 1069-1:2026 define?

  • Water slide - Equipment or an installation with a sliding surface on which the user moves with water as the friction- and/or speed-reducing medium.
  • Public use - Use open to everyone or to a defined user group, not limited to the owner’s family and guests.
  • Slide proper - The part intended for sliding, distinct from the access, start, and landing areas.
  • Final part - The part of the slide proper that prepares the user for landing.
  • Catch unit - An integral part that brings the rider to a halt in the sliding position.
  • Sofa unit - An integral part that slows the rider and moves them sideways out of the path of following users.
  • Splashdown area - A pool or part of a pool where the user lands from the slide and is stopped in the water.
  • Clearance zone - Controlled space around the user on the slide proper and final part designed to prevent impact with obstacles.

Who uses EN 1069-1:2026?

EN 1069-1:2026 is used by slide designers, manufacturers, installers, operators, slide testers, and inspection bodies. It is also relevant for swimming pool owners, facility managers, and buyers who need to define or review a slide project.

In practice, designers use it for layout, loads, and risk assessment; manufacturers use it for materials, fabrication, and marking; operators use it for commissioning, inspection, and flow control; and testers use it for practical checks and test reports. It is especially relevant in public swimming pools and open-water leisure facilities where user safety depends on both the structure and the way it is operated.

What changed in EN 1069-1:2026 from the previous edition?

EN 1069-1:2026 supersedes EN 1069-1:2017+A1:2019. The stated technical changes are:

  • The scope was extended to include open water areas for public use.
  • Clause 2 on normative references was revised.
  • Clause 3 on terms and definitions was revised.
  • Clause 4 on classification was revised, with deletion of Type 2.2 and Types 8, 9, and 10, and addition of special elements.
  • Protection against falling was revised and made applicable to all types.
  • Landing device and landing area requirements were revised and reorganized.
  • Splashdown area requirements were moved and revised.
  • Clause 8 on additional safety requirements was revised, including updated dimensional requirements and figures.
  • Editorial changes were made throughout the document.

Which standards are used with EN 1069-1:2026?

ReferenceWhat it contributes
prEN 1069-2:2025Instructions for water slides, including information and documentation requirements
EN 1990Basis for structural and geotechnical design
EN 1991-1-1Imposed loads and self-weight for structures
EN 1991-1-3:2025Snow loads
EN 1991-1-4Wind actions
EN 10088-1List of stainless steels
EN 10088-2Technical delivery conditions for stainless steel sheet, plate, and strip
EN 10204:2004Types of inspection documents for safety-critical materials
EN 13451-1:2020+A1:2024General safety requirements and test methods for pool equipment
EN 13451-2Safety requirements for ladders, stepladders, and handle bends
EN 13451-3Safety requirements for inlets, outlets, and water/air-based leisure features
EN 15288-1:2018+A1:2024Safety requirements for design of public swimming pools
EN 15288-2Safety requirements for operation of public swimming pools
EN 22768-1General tolerances for linear and angular dimensions
EN ISO 9606-1Qualification testing of welders for fusion welding
EN ISO/IEC 17025Competence requirements for testing and calibration laboratories

What does the EN 1069-1:2026 document contain?

EN 1069-1:2026 contains classification tables, dimensional rules, structural load rules, and type-specific safety provisions. It also includes normative annexes with splashdown area layouts, stainless steel selection guidance, and design loads for accesses and platforms.

The document gives practical test methods for checking sliding behavior, acceleration, speed, and landing safety. It also includes a test-report structure, so results can be documented in a way that supports commissioning, inspection, and conformity assessment.

Relations

Effective Date
09-Jul-2024
Effective Date
28-Oct-2026
Effective Date
07-Oct-2026
Effective Date
07-Oct-2026
Effective Date
07-Oct-2026
Effective Date
07-Oct-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026
Effective Date
05-Aug-2026

Buy Documents

Standard

EN 1069-1:2026

English language (56 pages)
Preview
Preview
e-Library read for
×1 day

Frequently Asked Questions

EN 1069-1:2026 is a standard published by the European Committee for Standardization (CEN). Its full title is "Water slides - Part 1: Safety requirements and test methods". This standard covers: This document is applicable to all water slides installed at open water areas for public use or in swimming pools for public use. This document specifies general safety requirements for water slides installed at open water areas for public use or in swimming pools for public use and specific requirements for defined types of water slides. These specific safety requirements are also applicable to undefined types as far as possible. These requirements concern safety and the technical rules for design, calculation and testing.

This document is applicable to all water slides installed at open water areas for public use or in swimming pools for public use. This document specifies general safety requirements for water slides installed at open water areas for public use or in swimming pools for public use and specific requirements for defined types of water slides. These specific safety requirements are also applicable to undefined types as far as possible. These requirements concern safety and the technical rules for design, calculation and testing.

EN 1069-1:2026 is classified under the following ICS (International Classification for Standards) categories: 97.220.40 - Outdoor and water sports equipment. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 1069-1:2026 has the following relationships with other standards: It is inter standard links to EN 1069-1:2017+A1:2019, EN 15288-1:2018+A1:2024, EN 1991-1-4:2026, EN 1991-1-3:2025, EN 13451-2:2015+A1:2020, EN 1991-1-1:2025, EN 13451-3:2011+A3:2016, EN 13451-3:2011+A1:2013, EN 13451-3:2022+A1:2025, EN 17232:2020, EN 13451-3:2022, EN 13451-3:2011, EN 13451-3:2011+A2:2014. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 1069-1:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN 1069-1:2017+A1:2019
Vodni tobogani - 1. del: Varnostne zahteve in preskusne metode
Water slides - Part 1: Safety requirements and test methods
Wasserrutschen - Teil 1: Sicherheitstechnische Anforderungen und Prüfverfahren
Toboggans aquatiques - Partie 1 : Exigences de sécurité et méthodes d'essai
Ta slovenski standard je istoveten z: EN 1069-1:2026
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 1069-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2026
EUROPÄISCHE NORM
ICS 97.220.40 Supersedes EN 1069-1:2017+A1:2019
English Version
Water slides - Part 1: Safety requirements and test
methods
Toboggans aquatiques - Partie 1 : Exigences de sécurité Wasserrutschen - Teil 1: Sicherheitstechnische
et méthodes d'essai Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 22 June 2026.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1069-1:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
Introduction . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Classification. 12
4.1 Type 1 . 12
4.1.1 Type 1.1 . 12
4.1.2 Type 1.2 . 12
4.2 Type 2 . 12
4.3 Type 3 . 12
4.4 Type 4 . 12
4.5 Type 5 . 13
4.6 Type 6 . 13
4.6.1 Type 6.1 . 13
4.6.2 Type 6.2 . 13
4.7 Type 7 . 13
4.8 Special elements . 13
4.8.1 Bowl . 13
4.8.2 Element that allows lateral oscillation . 13
4.8.3 Uphill element . 13
4.8.4 Wild river . 13
5 Materials and construction . 13
5.1 General. 13
5.2 Selection of materials . 14
5.3 Certificates . 14
5.4 Manufacturer and installer . 14
5.5 Durability . 14
5.6 Electrical installations . 14
6 Design . 14
6.1 Design guidelines . 14
6.2 Design analysis . 15
6.2.1 General. 15
6.2.2 Preliminary risk assessment . 15
6.2.3 Construction documents . 16
6.3 Static calculations . 16
6.3.1 General. 16
6.3.2 Actions in the slide area . 17
6.3.3 Actions on access, platforms and railings . 21
6.3.4 Combination of actions and verification . 21
7 Safety requirements for water slides . 21
7.1 General. 21
7.2 Entrapment . 22
7.3 Surfaces . 22
7.3.1 General . 22
7.3.2 Surface of the slide proper . 22
7.4 Corners and edges . 22
7.5 Access to water slides . 22
7.5.1 General . 22
7.5.2 Stairs. 22
7.5.3 Stepladders . 22
7.5.4 Platform . 23
7.5.5 Protection against falling . 23
7.5.6 Slip resistance . 24
7.6 Start section . 25
7.7 Slide proper . 25
7.7.1 General . 25
7.7.2 Sliding path . 25
7.7.3 Maximum acceleration on a sliding person . 25
7.8 Tubes and covered sections . 26
7.9 Final part . 26
7.10 Landing device/landing area. 26
7.10.1 General . 26
7.10.2 Catch unit . 26
7.10.3 Sofa unit . 27
7.10.4 Splashdown areas . 27
7.11 Accessories . 27
7.11.1 Covers . 27
7.11.2 Ride enhancement devices . 28
7.11.3 Other constituent parts . 28
7.12 Water supply . 30
7.12.1 General . 30
7.12.2 Water flow rate . 30
7.13 Interference between users . 30
8 Additional safety requirements for Types 1 to 7 and special elements . 30
8.1 Slide proper . 30
8.1.1 General . 30
8.1.2 Type 1. 31
8.1.3 Type 2. 31
8.1.4 Type 3. 32
8.1.5 Type 4. 32
8.1.6 Type 5. 33
8.1.7 Type 6. 34
8.1.8 Type 7. 35
8.1.9 Requirements for special elements . 35
8.2 Splashdown area . 36
8.2.1 General and specific pools . 36
8.2.2 Requirements for landing. 37
8.3 Clearance zones . 38
8.4 Interference between users and non-users . 39
9 Check and test runs . 39
9.1 General . 39
9.2 Technical and physical checks . 40
9.3 Practical test . 40
9.3.1 General . 40
9.3.2 Slide tester . 40
9.3.3 Sliding conditions . 40
9.3.4 Acceleration and speed measurements . 40
9.4 Test report . 41
10 Designation and marking . 42
10.1 Designation . 42
10.2 Marking . 42
Annex A (normative) Splashdown areas . 43
Annex B (normative) Use of stainless steels for water slides . 49
B.1 General. 49
B.2 Indoor swimming pools with disinfection with chlorine . 49
B.2.1 General. 49
B.2.2 Materials without regular cleaning . 49
B.2.3 Materials with regular cleaning. 49
B.2.3.1 General. 49
B.2.3.2 Cleaning concept . 50
B.2.3.3 Execution of the regular cleaning . 50
B.2.3.4 Regular inspection. 50
B.2.4 Outdoor swimming pools with disinfection with chlorine . 50
B.3 Coatings and paintings . 50
Annex C (normative) Design loads, accesses and platforms . 51
C.1 Vertical imposed loads . 51
C.2 Horizontal imposed loads . 51
C.3 Stiffness . 52
C.4 Stairs . 52
Annex D (informative) Acceleration and speed measurements . 54
D.1 Test devices . 54
D.1.1 General. 54
D.1.2 Acceleration measuring device . 54
D.1.3 Maximum speed measuring device . 54
D.2 Description of the acceleration test method . 54
Bibliography . 55

European foreword
This document (EN 1069-1:2026) has been prepared by Technical Committee CEN/TC 136 “Sports,
playground and other recreational facilities and equipment”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2027, and conflicting national standards shall
be withdrawn at the latest by January 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1069-1:2017+A1:2019.
EN 1069-1:2017+A1:2019:
a) change of scope: “to all water slides installed at open water areas for public use or in swimming pools
for public use” → ”open water areas” has been added to open the scope to other water facilities;
b) Clause 2 “Normative references” has been revised;
c) Clause 3 “Terms and definitions”, has been revised;
d) Clause 4, “Classification” has been revised:
deletion of Type 2 and Type 8, Type 9, Type 10, therefore a new subclause 4.8 “Special elements”
has been added;
e) subclause 7.5.5, “Protection against falling” has been revised; now applicable to all Types;
f) subclause 7.9.2, “Landing device/Landing area” moved to own subclause 7.10 and has been revised;
g) “Splashdown areas” moved to subclause 7.10.5;
h) Clause 8 “Additional safety requirements for Types 1 to 7 and special elements” has been revised:
table for dimensions and falling distance/water depth of Type 1 and Type 2, cross section of Type 6
has been added; Figure 14 has been revised; Figure 15 “Difference in height” has been deleted; new
Figure 15 “Clearance dimensions” has been added;
i) the document has been editorially revised.
EN 1069, Water slides, consists of the following parts:
— Part 1: Safety requirements and test methods
— Part 2: Instructions
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
The market for water slides is extremely wide and specific and still developing. It is impossible to define
an all-embracing safety specification, including dimensions and design requirements as required by a
standard, without limiting the design possibilities and preventing innovative and new but safe products.
This document is intended to establish safety requirements and design guidance rules to serve anyone
involved with water slides, especially designers, manufacturers, operators and users, to ensure safe and
more efficient products. Its basic approach is the consciousness that the sliding action usually implies for
the users a higher risk level than using a pool. For certain aspects of design, manufacturing, installation,
operation and use only specific guidelines, without any technical specification, are given, which should
be taken into consideration and be fulfilled in order to ensure safety for operators and users.

1 Scope
This document is applicable to all water slides installed at open water areas for public use or in swimming
pools for public use.
This document specifies general safety requirements for water slides installed at open water areas for
public use or in swimming pools for public use and specific requirements for defined types of water slides.
These specific safety requirements are also applicable to undefined types as far as possible.
These requirements concern safety and the technical rules for design, calculation and testing.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1069-2:2026, Water slides — Part 2: Instructions
EN 1990, Eurocode — Basis of structural and geotechnical design
EN 1991-1-1, Eurocode 1 — Actions on structures — Part 1-1: Specific weight of materials, self-weight of
construction works and imposed loads for buildings
EN 1991-1-3:2025, Eurocode 1 — Actions on structures — Part 1-3: Snow loads
EN 1991-1-4, Eurocode 1: Actions on structures — Part 1-4: General actions — Wind actions
EN 10088-1, Stainless steels — Part 1: List of stainless steels
EN 10088-2, Stainless steels — Part 2: Technical delivery conditions for sheet/plate and strip of corrosion
resistant steels for general purposes
EN 10204:2004, Metallic products — Types of inspection documents
EN 13451-1:2020+A1:2024, Swimming pool equipment — Part 1: General safety requirements and test
methods for equipment installed in pools for public use
EN 13451-2, Swimming pool equipment — Part 2: Additional specific safety requirements and test methods
for ladders, stepladders and handle bends
EN 13451-3, Swimming pool equipment — Part 3: Additional specific safety requirements and test methods
for inlets and outlets and water/air based water leisure features installed in pools for public use
EN 15288-1:2018+A1:2024, Swimming pools for public use — Part 1: Safety requirements for design
EN 15288-2, Swimming pools for public use — Part 2: Safety requirements for operation
EN 22768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications (ISO 2768-1)
EN ISO 9606-1, Qualification testing of welders — Fusion welding — Part 1: Steels (ISO 9606-1)
EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
(ISO/IEC 17025)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
pool/swimming pool
facility, with one or more water areas, intended for swimming, leisure or other water-based physical
activities
[SOURCE: EN 15288-1:2018+A1:2024, 3.1]
3.2
open water area
surface water intended for swimming, leisure without water treatment
Note 1 to entry: Water collected on the ground e.g. lakes, rivers, sea …
3.3
public use
use of an installation open to everyone or to a defined group of users, not designated solely for the
owner’s/proprietor’s/operator’s family and guests independently from paying an entrance fee
Note 1 to entry: Pools serving houses rented for private use are not of public use.
[SOURCE: EN 15288-1:2018+A1:2024, 3.5, modified – Note 1 to entry has been added.]
3.4
water slide
piece of equipment or installation with a sliding surface on which the user slides with water as a friction-
and/or speed-reducing medium; the user slides freely or with the use of a ride enhancement device
Note 1 to entry: On some water slides the user can also be pushed e.g. by a water stream.
Note 2 to entry: For classification see Clause 4.
3.5
platform
area providing access to the start section
3.6
start section
area where the user enters the water slide proper and takes the sliding position
3.7
slide proper
area intended for sliding
3.8
final part
part of the water slide proper designed to prepare the user for landing
3.9
landing
conclusion of sliding action
Note 1 to entry: Types of conclusion can be fall, being slowed down and stopped in a catch unit or sofa.
3.10
catch unit
integral part of a water slide, which brings the rider to a halt in his sliding position
Note 1 to entry: See Figure 1 as example.

Key
1 water line
Figure 1 — Example of typical catch unit
3.11
sofa unit
integral part of a water slide, which slows down the rider on the sliding surface and moves him
additionally sideways out of the sliding path of the following users
Note 1 to entry: See Figure 2 as example.
Key
1 water line
Figure 2 — Example of typical sofa unit
3.12
splashdown area
specific pool or area which is part of a general purpose pool, in which the user lands from the end of the
water slide, and is brought to a halt in the water
3.13
water level
defined operating water surface in the landing area
3.14
tube
closed section, not necessarily circular in cross section, of a water slide, with a fully utilisable sliding
surface
3.15
cover
device to enclose an open water slide, not intended for sliding
3.16
riser
extension for the water slide proper, intended for sliding
3.17
wave screen
device, placed within the clearance zone, to control spilling water
3.18
ride enhancement device
device to slide on or in, designed for a particular water slide
3.19
barrier
device to restrict users from falling over, under or through it
3.20
average inclination
inclination x in percent (%) calculated with the formula
xh× 100 / l
( )
where
h is the height between start section and beginning of final part, in metres;
l is the developed length of the water slide proper excluding the final part, in metres.
3.21
clearance zone
controlled space around the user on the water slide proper and on the final part, designed to prevent the
impact of the users with obstacles
4 Classification
4.1 Type 1
4.1.1 Type 1.1
Straight water slides not exceeding 1 000 mm in height from start section to water level and with an
average inclination ≤ 70 %.
NOTE This water slide is typically designed for small children.
4.1.2 Type 1.2
Straight slide with an average inclination of ≤ 70 % and a height of 1 000 mm < h ≤ 3 000 mm from start
section to water level.
NOTE This water slide is typically designed for children.
4.2 Type 2
Curved single-track water slide with an average inclination of ≤ 70 % and a height of ≤ 3 000 mm from
start section to water level.
NOTE This water slide is typically designed for children.
4.3 Type 3
Single-track water slide, with an average inclination of maximum 13 %, excluding the final part. The
maximum speed of the users shall be ≤ 8 m/s.
NOTE The average speed of the users is usually ≤ 6 m/s.
4.4 Type 4
Speed single-track water slide with an average inclination between 13 % and 20 %, excluding the final
part. The maximum speed of the users shall be ≤ 14 m/s.
NOTE The average speed of the users is usually ≤ 10 m/s.
=
4.5 Type 5
High-speed single-track water slide with an average inclination of at least 20 %, excluding the final part.
The maximum speed of the users may be > 14 m/s.
4.6 Type 6
4.6.1 Type 6.1
Multi-track water slide with separate parallel tracks, with an average inclination of maximum 13 %
excluding the final part, one beside the other over the full length. The maximum speed of the users shall
be ≤ 8 m/s.
NOTE The average speed of the users is usually ≤ 6 m/s.
4.6.2 Type 6.2
Multi-track water slide with separate parallel tracks, with an average inclination of between 13 % and
30 %, excluding the final part. The maximum speed of the users shall be ≤ 14 m/s.
NOTE The average speed of the users is usually ≤ 10 m/s.
4.7 Type 7
Wide straight water slide with an average inclination of maximum 35 %. The maximum speed of the users
shall be ≤ 8 m/s.
4.8 Special elements
4.8.1 Bowl
Special element within a water slide where the user exits from a water slide of another type into a circular
bowl and descends in a spiral path, before either free falling through a hole at the bottom into the
splashdown area or entering an additional slide.
4.8.2 Element that allows lateral oscillation
A special element where the user exits from a water slide of another type into a U-shaped part allowing
free transversal oscillating sliding in direction to the end of the element.
EXAMPLE A cone or a halfpipe.
4.8.3 Uphill element
A special element where the user slides upwards, sometimes with the help of jets or a specific device.
4.8.4 Wild river
A combination of water slide elements with various cross sections where the user slides, floats or swims
in a volume of water. The slide can divide in multiple tracks of other types which can congregate to a
single track.
5 Materials and construction
5.1 General
Any material may be used for the construction of water slides, supports and ride enhancement devices,
provided that it fulfils the requirements of this document.
5.2 Selection of materials
All materials and finishes used shall be:
a) suitable for the selected use, the respective surroundings and conditions;
b) able to withstand conditions of high humidity with occasional saturation and/or corrosiveness;
c) not encouraging the growth of bacteria.
The use of stressed stainless steel subjected to intergranular stress corrosion cracking shall be avoided,
unless it can be inspected and regularly cleaned. Where stainless steel is used, the grade used shall be in
accordance with Annex B.
5.3 Certificates
Certificates for safety critical building materials (e.g. load bearing materials) shall comply at least with
EN 10204:2004, test report “Type 2.2”.
NOTE Specific national regulations can apply.
5.4 Manufacturer and installer
The manufacturer and the installer shall ensure that persons engaged in the construction and the
installation of the water slide are competent to carry out the work, and that welders are suitably qualified
and accepted according to EN ISO 9606-1. Any assembling, modification, adjustment or alteration of parts
shall only be done by persons with appropriate experience and skills.
5.5 Durability
The designer shall specify the method of protection or frequency of inspection. All components shall be
protected to minimize degradation caused by corrosion or rot by an approved method. The quality of
protection shall depend on the use of the components. Where hollow section structural steel is used,
internal corrosion shall be considered.
5.6 Electrical installations
Relevant national and European regulations for electrical installations in and at buildings (e.g. swimming
pool, swimming pool surround) apply.
NOTE See HD 60364-7-702.
6 Design
6.1 Design guidelines
The design of a water slide, as a standard model or a one-off installation conforming to the client’s
specifications, shall consider at least:
— EN 15288-1 and EN 15288-2;
— the intended user group, e.g. children, adults, users with special requirements;
— ambient conditions, e.g. indoor, outdoor.
In the design document’s possible/allowed user groups, their characteristics and limits shall be indicated.
NOTE Various risks can be involved in using a water slide, e.g. ejection from the water slide, impacts, falls,
burns, or entrapment. For guidance to a risk assessment, see EN 15288-2 and EN 1069-2.
6.2 Design analysis
6.2.1 General
Water slides shall be treated as structures, Type 1 and Type 2 water slides only when applicable.
Attention is drawn to the statutory requirements e.g. with regard to means of access and means of
support.
6.2.2 Preliminary risk assessment
A preliminary risk assessment shall be performed by the designer at the design stage for every water
slide, with the purpose of identifying possible hazards and hazardous situations that can occur by its use,
paying attention to the fact that the riding of water slides can be a vigorous physical activity and the risks
associated are greater than those usually encountered in a swimming pool. The preliminary risk
assessment shall consider different user groups (e.g. adults, children, people with reduced ability). The
risk assessment shall ensure the conformity of the design to this document.
Some typical issues to be considered are:
— type of water slide;
— intended users;
— implementation of the water slide into a new swimming pool complex;
— integration of the water slide into an existing facility;
— distance control (e.g. interference between users);
— access control (e.g. interference between users and non-users);
— hazards related to the slide proper including those coming from possible vandalism especially parts
freely accessible;
— hazards related to the landing;
— risky behaviours of the users;
— surroundings;
— traffic to and from the water slide;
— influence of the use of the water slide on the regular operation of the whole facility.
The risks shall be assessed against the safety of user groups, especially of those with special needs.
This assessment is even more important for water slides not yet classified in this document and shall also
consider the specific safety requirements given in Clause 8, to comply with them as far as possible.
The results of the preliminary risk assessment shall be made available to the water slide tester who will
perform the practical test according to 9.3.
NOTE Specific national regulation can apply.
6.2.3 Construction documents
The construction documents shall be provided to the customer. They shall contain all documents required
for the assessment of the stability and operational safety of the water slide. The requirements for
documentation given in EN 1069-2:2026, Clause 6 shall be observed.
The construction documents for Type 3 to Type 7 and special elements shall include as a minimum:
— type of water slide;
— declaration of conformity to this document for the construction;
— full design and fabrication drawings;
— statement about intended use;
— construction method statement;
— comprehensive stress and stability analysis as required by the Eurocodes;
— description of special features of the water slide;
— description and dimensions of any clearance zones;
— specification of all materials;
— specification of electrical installation;
— any restrictions related to the users;
— name and/or logo and the address of the manufacturer, supplier, importer or installer;
— designation.
NOTE Type 1 and Type 2 water slides can require a simplified documentation.
6.3 Static calculations
6.3.1 General
The structural analysis of the complete water slide including the supports shall be performed using the
safety concept according to Eurocode EN 1990 and associated parts using the partial factor method
according to Table 1, Table 2 and Table 3 and the combination factors according to Table 4.
Table 1 — Partial factors for Ultimate Limit combinations
Permanent actions Variable actions
Unfavourable Favourable Leading variable action Accompanying action
γ = 1,35 γ = 1,00 γ = 1,50 γ = 1,50
G,i G,i Q,1 Q,i
Table 2 — Partial factors for serviceability combinations
Permanent actions Variable actions
Unfavourable Favourable Leading variable action Accompanying action
γ = 1,00 γ = 1,00 γ = 1,00 γ = 1,00
G,i G,i Q,1 Q,i
Table 3 — Partial factors for combinations of accidental actions
Permanent actions Variable actions
Unfavourable Favourable Leading variable action Accompanying action
γG,i = 1,00 γG,i = 1,00 γQ,1 = 1,00 γQ,i = 1,00

Table 4 — Combination factors ψ , ψ and ψ
0 1 2
Action ψ ψ ψ
0 1 2
...