Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)

ISO 8469:2013 specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m.
It applies to hoses for small craft with permanently installed fuel systems.
Specifications for fire-resistant hoses are given in ISO 7840. Specifications for permanently installed fuel systems are given in ISO 10088.

Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige Kraftstoffschläuche (ISO 8469:2013)

Diese Internationale Norm legt die allgemeinen Anforderungen und physikalischen Prüfungen für nicht feuerwiderstandsfähige Schläuche fest, in denen Benzin oder ein Benzin-Ethanol-Gemisch oder Diesel oder ein Diesel-FAME-Gemisch geleitet wird. Dabei sind Schläuche mit Innendurchmesser bis einschließlich 10 mm für Betriebsüberdrücke bis höchstens 0,34 MPa ausgelegt und Schläuche mit Innendurchmesser bis 63 mm für Betriebsüberdrücke bis höchstens 0,25 MPa für Wasserfahrzeuge mit einer Rumpflänge bis 24 m.
Sie gilt für Schläuche auf kleinen Wasserfahrzeugen mit fest eingebauten Kraftstoffsystemen.
Festlegungen für feuerwiderstandsfähige Schläuche sind in ISO 7840 [1] gegeben. Festlegungen für fest eingebaute Kraftstoffsysteme sind in ISO 10088 [2] enthalten.

Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2013)

L'ISO 8469:2013 spécifie les exigences générales et les essais physiques relatifs aux tuyaux souples non résistants au feu pour le transport d'essence ou de mélanges essence/éthanol et de carburant diesel ou de mélanges diesel/esters méthyliques d'acide gras (EMAG), conçus pour une pression de service n'excédant pas 0,34 MPa pour les tuyaux de diamètre intérieur nominal inférieur ou égal à 10 mm, et 0,25 MPa pour les tuyaux de diamètre intérieur allant jusqu'à 63 mm, installés sur les bateaux dont la longueur de coque est inférieure ou égale à 24 m
Elle s'applique aux tuyaux souples destinés aux petits navires dont le système à carburant est installé à demeure.
Les spécifications applicables aux tuyaux à carburant résistants au feu figurent dans l'ISO 7840. Les spécifications pour les systèmes carburant installés à demeure sont données dans l'ISO 10088.

Mala plovila - Gorljive cevi za gorivo (ISO 8469:2013)

Ta mednarodni standard določa splošne zahteve in fizične preskuse za gorljive cevi za pretakanje bencinskega goriva ali mešanice bencinskega goriva, etanola in dizelskega goriva ali mešanice dizelskega goriva in metilnih estrov maščobnih kislin (FAME), ki so zasnovane za uporabo pri delovnem tlaku največ 0,34 MPa za cevi z notranjim premerom največ 10 mm ter 0,25 MPa za cevi z notranjim premerom največ 63 mm v plovilu z dolžino trupa do 24 m. Uporablja se za cevi za mala plovila s trajno vgrajenim sistemom za gorivo. Specifikacije za negorljive cevi so podane v standardu ISO 7840[1]. Specifikacije za trajno vgrajene sisteme za gorivo so podane v standardu ISO 10088.

General Information

Status
Withdrawn
Publication Date
23-Jul-2013
Withdrawal Date
25-Sep-2018
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
26-Sep-2018

Relations

Buy Standard

Standard
EN ISO 8469:2013
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8469:2013
01-oktober-2013
1DGRPHãþD
SIST EN ISO 8469:2007
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2013)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
Kleine Wasserfahrzeuge - Nicht feuerstandsfähige Kraftstoffschläuche (ISO 8469:2013)
Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2013)
Ta slovenski standard je istoveten z: EN ISO 8469:2013
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
47.020.30 Sistemi cevi Piping systems
47.080 ýROQL Small craft
SIST EN ISO 8469:2013 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8469:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 8469:2013


EUROPEAN STANDARD
EN ISO 8469

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2013
ICS 47.080 Supersedes EN ISO 8469:2006
English Version
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
Petits navires - Tuyaux souples pour carburant non Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige
résistants au feu (ISO 8469:2013) Kraftstoffschläuche (ISO 8469:2013)
This European Standard was approved by CEN on 8 June 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8469:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8469:2013
EN ISO 8469:2013 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 8469:2013
EN ISO 8469:2013 (E)
Foreword
This document (EN ISO 8469:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at
the latest by January 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8469:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8469:2013 has been approved by CEN as EN ISO 8469:2013 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.