EN 1218-1:1999/prA1
(Amendment)Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
Replace first paragraph with: "This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to single end tenoning machines with sliding table, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph in its entirety.
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 1: Einseitige Zapfenschneid- und Schlitzmaschinen mit Schiebetisch
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 1: Tenonneuses simples alimentées par table à rouleaux
Varnost lesnoobdelovalnih strojev - Stroji za izdelovanje čepov in utorov - 1. del: Enostranski stroji s podajalno mizo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
(QRVWUDQVNLVWURMLVSRGDMDOQRPL]R
Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning
machines with sliding table
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 1: Einseitige Zapfenschneid- und Schlitzmaschinen mit Schiebetisch
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 1: Tenonneuses
simples alimentées par table à rouleaux
Ta slovenski standard je istoveten z: EN 1218-1:1999/prA1
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 1218-1:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Tenoning machines - Part 1:
Single end tenoning machines with sliding table
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 1: Tenonneuses simples alimentées Zapfenschneid- und Schlitzmaschinen - Teil 1: Einseitige
par table à rouleaux Zapfenschneid- und Schlitzmaschinen mit Schiebetisch
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1218-1:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-1:1999/prA1:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .4
1 Modification to the French title page .5
2 Modification to the Foreword .5
3 Modification to the Introduction .5
4 Modification to Clause 1, Scope .5
5 Modification to Clause 2, Normative references .5
6 Modification to Clause 3, Definitions .7
7 Modification to Clause 4, List of hazards .7
8 Modification to the hanging paragraph of Clause 5, Safety requirements and/or measures .9
9 Modification to 5.1.1, Safety and reliability of control systems .9
10 Modification to 5.1.3, Starting .9
11 Modification to 5.1.4, Normal stopping .9
12 Modification to 5.1.5, Emergency stop .9
13 Modification to 5.1.8, Speed changing .9
14 Modification to 5.1.9, Control duplication .9
15 Modification to 5.1.10, Failure of the power supply . 10
16 Modification to 5.2.2, Risk of break-up during operation . 10
17 Modification to 5.2.3.2, Strength . 10
18 Modification to 5.2.3.5, Spindle locking. 10
19 Modification to 5.2.3.6, Spindle rings . 10
20 Modification to 5.2.7, Prevention of access to moving parts . 10
21 Modification to 5.3.1, Fire and explosion . 10
22 Modification to 5.3.4, Electricity . 10
23 Modification to 5.3.5, Ergonomics and handling . 11
24 Modification to 5.3.7, Pneumatics . 11
25 Modification to 5.3.8, Hydraulics . 11
26 Modification to 5.3.15, Isolation . 11
27 Modification to 5.3.16, Maintenance . 11
28 Modification to Clause 6, Information for use . 12
29 Modification to 6.2, Marking . 12
30 Modification to 6.3, Instruction handbook . 12
31 Modification to Annex A . 14
32 Modification to Annex C, Examples of safety related control systems . 15
33 Modification to Annex D, Bibliography. 15
34 Modification to Annex ZA . 15
35 Addition of Annex ZB . 16
Foreword
This document (EN 1218-1:1999/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the French title page
rd
Replace the 3 element of the title with "Partie 1: Tenonneuses simples alimentées par table à rouleaux".
2 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
3 Modification to the Introduction
Replace "EN 292:1991" with "EN ISO 12100-1:2003".
4 Modification to Clause 1, Scope
Replace first paragraph with: "This document deals with the significant hazards, hazardous situations and
events as listed in Clause 4 which are relevant to single end tenoning machines with sliding table, hereinafter
referred to as “machines”, designed to cut solid wood, chipboard, fibreboard, plywood and also these
materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph in its entirety.
5 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Delete the reference to EN 294:1992 and add "EN ISO 13857:2008, Safety of machinery — Safety distances
to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)" and replace
"EN 294:1992" with "EN ISO 13857:2008" throughout the document.
Delete reference to EN 418:1992 and add "EN ISO 13850:2006, Safety of machinery — Emergency stop —
nd rd
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 2 and 3 paragraphs, with
"EN ISO 13850:2006".
Replace "EN 847-1:1997" with "EN 847-1:2005" throughout the document.
Replace the title of "EN 953" with "Safety of machinery — Guards — General requirements for the design and
construction of fixed and movable guards".
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 204-1:1992, modified)" with "(IEC 60204-1:2005, modified".
Replace "EN 848-1:1997" with "EN 848-1:2007" throughout the document.
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1991" with "EN 60497-5-1:2004" throughout the document and replace in the title
"(IEC 947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Delete reference to "ISO 3745:1977" and add "EN ISO 3745:2003, Acoustics — Determination of sound
power levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic
rooms (ISO 3745:2003)" and replace "ISO 3745:1997" with "EN ISO 3745:2003" throughout the document.
Delete reference to "ISO/TR 11688-1:1995" and add "EN ISO 11688-1:1998, Acoustics — Recommended
practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995)"
and replace "ISO/TR 11688-1:1995" with "EN ISO 11688-1:1998" throughout the document.
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace
"HD 21.1 S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace
"HD 22.2 S3:1997" with "HD 22.1 S4:2002" throughout the document.
To add reference to:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up",
"EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, auditory and tactile signals (IEC 61310-1:2007)",
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
6 Modification to Clause 3, Definitions
Replace term i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.