SIST EN 1218-1:2000/kprA1:2009

Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table

Replace first paragraph with: "This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to single end tenoning machines with sliding table, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph in its entirety.

Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 1: Einseitige Zapfenschneid- und Schlitzmaschinen mit Schiebetisch

Sécurité des machines pour le travail du bois - Tenonneuses - Partie 1: Tenonneuses simples alimentées par table à rouleaux

Varnost lesnoobdelovalnih strojev - Stroji za izdelovanje čepov in utorov - 1. del: Enostranski stroji s podajalno mizo

General Information

• Status: Not Published
• Public Enquiry End Date: 03-May-2009
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: VSN - Safety of machinery
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 10-Sep-2012
• Due Date: 15-Sep-2012
• Completion Date: 10-Sep-2012
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 1218-1:1999/prA1 - Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table

Relations

• Amends: SIST EN 1218-1:2000 - Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
• Effective Date: 01-Apr-2009
• Consolidated By: SIST EN 1218-1:2000+A1:2009 - Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
• Effective Date: 18-Jan-2023
• Consolidated By: SIST EN 1218-1:2000+A1:2009 - Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
• Effective Date: 19-Jan-2023
• Consolidated By: SIST EN 1218-1:2000+A1:2009 - Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
• Effective Date: 01-Oct-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1218-1:2000/kprA1:2009
01-april-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
(QRVWUDQVNLVWURMLVSRGDMDOQRPL]R
Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning
machines with sliding table
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 1: Einseitige Zapfenschneid- und Schlitzmaschinen mit Schiebetisch
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 1: Tenonneuses
simples alimentées par table à rouleaux
Ta slovenski standard je istoveten z: EN 1218-1:1999/prA1
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1218-1:2000/kprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1218-1:2000/kprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1218-1:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10

English Version
Safety of woodworking machines - Tenoning machines - Part 1:
Single end tenoning machines with sliding table
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 1: Tenonneuses simples alimentées Zapfenschneid- und Schlitzmaschinen - Teil 1: Einseitige
par table à rouleaux Zapfenschneid- und Schlitzmaschinen mit Schiebetisch
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1218-1:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-1:1999/prA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
Contents Page
Foreword .4
1 Modification to the French title page .5
2 Modification to the Foreword .5
3 Modification to the Introduction .5
4 Modification to Clause 1, Scope .5
5 Modification to Clause 2, Normative references .5
6 Modification to Clause 3, Definitions .7
7 Modification to Clause 4, List of hazards .7
8 Modification to the hanging paragraph of Clause 5, Safety requirements and/or measures .9
9 Modification to 5.1.1, Safety and reliability of control systems .9
10 Modification to 5.1.3, Starting .9
11 Modification to 5.1.4, Normal stopping .9
12 Modification to 5.1.5, Emergency stop .9
13 Modification to 5.1.8, Speed changing .9
14 Modification to 5.1.9, Control duplication .9
15 Modification to 5.1.10, Failure of the power supply . 10
16 Modification to 5.2.2, Risk of break-up during operation . 10
17 Modification to 5.2.3.2, Strength . 10
18 Modification to 5.2.3.5, Spindle locking. 10
19 Modification to 5.2.3.6, Spindle rings . 10
20 Modification to 5.2.7, Prevention of access to moving parts . 10
21 Modification to 5.3.1, Fire and explosion . 10
22 Modification to 5.3.4, Electricity . 10
23 Modification to 5.3.5, Ergonomics and handling . 11
24 Modification to 5.3.7, Pneumatics . 11
25 Modification to 5.3.8, Hydraulics . 11
26 Modification to 5.3.15, Isolation . 11
27 Modification to 5.3.16, Maintenance . 11
28 Modification to Clause 6, Information for use . 12
29 Modification to 6.2, Marking . 12
30 Modification to 6.3, Instruction handbook . 12
31 Modification to Annex A . 14
32 Modification to Annex C, Examples of safety related control systems . 15
33 Modification to Annex D, Bibliography. 15
2

---------------------- Page: 4 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
34 Modification to Annex ZA . 15
35 Addition of Annex ZB . 16


3

---------------------- Page: 5 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
Foreword
This document (EN 1218-1:1999/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.

4

---------------------- Page: 6 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
1 Modification to the French title page
rd
Replace the 3 element of the title with "Partie 1: Tenonneuses simples alimentées par table à rouleaux".
2 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
3 Modification to the Introduction
Replace "EN 292:1991" with "EN ISO 12100-1:2003".
4 Modification to Clause 1, Scope
Replace first paragraph with: "This document deals with the significant hazards, hazardous situations and
events as listed in Clause 4 which are relevant to single end tenoning machines with sliding table, hereinafter
referred to as “machines”, designed to cut solid wood, chipboard, fibreboard, plywood and also these
materials where they are covered with plastic laminate or edgings.".
Delete the second paragraph in its entirety.
5 Modification to Clause 2, Normative references
Replace the standard paragraph with the following: "The following referenced documents are indispensable
for the application of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.".
Delete reference EN 292-1:1991 in Clause 2 and replace "EN 292-1:1991" with "EN ISO 12100-1:2003"
throughout the document.
Delete references EN 292-2:1991 and EN 292/A1:1995.
Delete the reference to EN 294:1992 and add "EN ISO 13857:2008, Safety of machinery — Safety distances
to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)" and replace
"EN 294:1992" with "EN ISO 13857:2008" throughout the document.
Delete reference to EN 418:1992 and add "EN ISO 13850:2006, Safety of machinery — Emergency stop —
nd rd
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.1.5, 2 and 3 paragraphs, with
"EN ISO 13850:2006".
Replace "EN 847-1:1997" with "EN 847-1:2005" throughout the document.
Replace the title of "EN 953" with "Safety of machinery — Guards — General requirements for the design and
construction of fixed and movable guards".
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 204-1:1992, modified)" with "(IEC 60204-1:2005, modified".
Replace "EN 848-1:1997" with "EN 848-1:2007" throughout the document.
5

---------------------- Page: 7 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1991" with "EN 60497-5-1:2004" throughout the document and replace in the title
"(IEC 947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Delete reference to "ISO 3745:1977" and add "EN ISO 3745:2003, Acoustics — Determination of sound
power levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic
rooms (ISO 3745:2003)" and replace "ISO 3745:1997" with "EN ISO 3745:2003" throughout the document.
Delete reference to "ISO/TR 11688-1:1995" and add "EN ISO 11688-1:1998, Acoustics — Recommended
practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995)"
and replace "ISO/TR 11688-1:1995" with "EN ISO 11688-1:1998" throughout the document.
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace
"HD 21.1 S3:1997" with "HD 21.1 S4:2002" throughout the document.
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace
"HD 22.2 S3:1997" with "HD 22.1 S4:2002" throughout the document.
To add reference to:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up",
"EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, auditory and tactile signals (IEC 61310-1:2007)",
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
6

---------------------- Page: 8 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
6 Modification to Clause 3, Definitions
Replace term in definition 3.7 with: "information from the supplier".
7 Modification to Clause 4, List of hazards
Replace title of Clause 4 with: "List of significant hazards".
Replace the clause content with:
"This clause contains the significant hazards, hazardous situations and events (see EN 1050:1996) as far as
they are dealt with in this document, identified by risk assessment as significant for the machines as defined in
the scope and which require action to eliminate or reduce the risk. This document deals with these significant
hazards by defining safety requirements and/or measures or by reference to relevant standards.
These hazards are listed in Table 1 in accordance with Annex A of EN 1050:1996.
Table 1 — List of significant hazards
Hazards, hazardous situations and Relevant sub-
No hazardous events EN ISO 12100 clause of this
document
 Part 1: Part 2:
2003 2003
1 Mechanical hazards related to:
- machine parts or work-pieces:
a) shape; 4.2 4.2.1, 5.2.3, 5.2.6,
4.2.2, 5 5.2.7, 5.2.8
b) relative location; 5.1.2, 5.1.5
d) mass and velocity (kinetic energy of 5.2.7, 6.3
elements in controlled or uncontrolled
motion);
e) mechanical strength. 5.2.2
 - accumulation of energy inside the machinery:
g) liquids and gases under pressure; 4.2 4.10, 5.5.4 5.3.7, 5.3.8
1.1 Crushing hazard 4.2.1 5.2.1, 5.2.7,
5.2.8


1.2 Shearing hazard 5.2.7, 5.2.8


1.3 Cutting or severing hazard 5.2.2, 5.2.3,

5.2.7, 5.2.8


1.4 Entanglement hazard 5.2.3, 5.2.4,

5.2.6, 5.2.7


1.5 Drawing-in or trapping hazard 5.2.7, 5.2.8

1.6 Impact hazard 5.2.7
1.9 High pressure fluid injection or ejection 5.3.7, 5.3.8
hazard
2 Electrical hazards due to:
7

---------------------- Page: 9 ----------------------

SIST EN 1218-1:2000/kprA1:2009
EN 1218-1:1999/prA1:2009 (E)
2.1 Contact of persons with live parts (direct 4.3 4.9, 5.5.4 5.3.4, 5.3.15
contact)
2.2 Contact of persons with parts which have 4.3 4.9 5.3.4, 5.3.15
become live under faulty conditions
(indirect contact)
4 Hazards generated by noise, resulting in:
Hearing loss (deafness), other 4.5 4.2.2, 5 5.3.2
4.1
physiological disorders (loss of balance,
loss of awareness)
Interference with speech communication, 5.3.2
4.2
acoustic signals
7 Hazards generated by materials and substances (and their constituent elements)
processed or used by the machinery
7.1 Hazards from contact with or inhalation of 4.8 4.3b, 4.4 5.3.3
harmful fluids and dusts
7.2 Fire hazard 4.8 4.4 5.3.1
8 Hazards generated by neglecting ergonomic principles in machinery design
related to:
8.1 Unhealthy postures or excessive effort 4.9 4.7, 4.8.2, 5.1.2
4.11.12,
5.5.5, 5.5.6
8.2 Hand-arm or foot-leg anat
...